Advertisement
Quick Links
32" HD Ready 1080p Digital LCD TV
Quick Start Guide
L32LCD11
Thank you
for purchasing your new Logik TV.
Your new TV incorporates the latest technology to enhance your
viewing experience. We would suggest that you allow about 20
mins for initial setup.
Please follow this guide for a successful rst time installation.
GB
1
1
Unpacking
Remove all packaging from the TV. Retain the packaging. If you
dispose of it please do so according to any local regulations.
LCD TV
Nut Stand
Base Stand
Washer
Remote Control /
Wrench
AAA Batteries x 2
Instruction Manual
AV Cable
Quick Start Guide
Screw Bolt
Digital Switchover
Nut
Addendum
2
2
Operating Your Remote Control
1. Press and lift the back
cover up to open the
battery compartment
of the remote control.
2. Insert two AAA size
batteries. Close the
battery compartment
cover.
Install the batteries correctly by following the polarity
(+ and -) indications in the battery compartment.
3
3
Installing the Base Stand
1. Lay the TV down on a
at surface with the back
2
side facing up. Please
make sure to place a soft
cushioned material (such
Unscrew
as a pillow or thick piece
of foam) beneath the
screen.
2. To install the base stand,
rst remove the stand
support from the TV by
untightening the 4
3
screws at the rear of the
TV Stand Support
TV.
3. Put the nut into the nut
Nut
stand to hold the nut and
place the nut stand into
the stand support.
Washer
Screw bolt
Screw
Nut
Assemble the washer in
Stand
Wrench
the back of base stand
and make sure the four
columns of base stand
4
through the hole of the
washer. Put the screw
Screw
bolt through the washer
and attach the base
stand to the stand
support by using the
wrench.
4. Attach the base stand
with the 4 screws.
4
4
Connecting the Aerial
OR
RF coaxial cable
(not included)
HDMI3
HDMI2
HDMI1
Connect one end of the RF coaxial cable to the aerial socket on
the wall and the other end of the cable to the RF IN (75 ) socket
at the rear right side of your TV.
Do not connect the TV to the mains supply until you
have completed all the connections.
6
6
Turning the TV On for the First Time
The rst time you turn the TV on, it will go straight into First Time Installation.
1. Press the OK button to
start First Time Installation.
Please ensure aerial is plugged in!!
Then press OK button to start
3. Press the
Country
to select UK as the
country where you will
UK
Germany
Portugal
operate the TV. Press the
OK button to con rm.
France
Italy
Spain
Menu
Well done,
your new TV is now ready to use. You will nd that there are many exciting features available. To get to know all these
features, please take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call our UK Call Centre on 0844 561 1234.
Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.
5
5
Connecting to the Mains Socket
To mains socket
1. Connect the mains cable to the mains socket after you have
completed all the connections.
2. Switch on the POWER ON/OFF switch which is located at the
rear left lower side of the TV. At this stage, the TV switches to
standby mode. The red LED indicator will illuminate on the
front panel of the TV.
3. In standby mode, press the
/ I button at the front right side
of the TV or the
button on the remote control to turn the TV
on. The red LED indicator will turn blue.
2. Press the
Please select an OSD Language
to select English as your
desired language to be
English
Español
Français
displayed on the menu.
Press the OK button to
Deutsch
Português
Italiano
con rm.
buttons
4. Channel tuning will
Channel Tuning
commence. This
TV
:
0 Channel
operation may take up to
DTV
:
0 Channel
6 minutes. The display
Radio
:
0 Channel
will show the progress of
Data
:
0 Channel
the tuning and the
number of channels
1 %...
471.25 MHz
(TV)
found.
Please press MENU key to skip
buttons
(P.N.: I.08.226329102)
Advertisement
