Download Print this page

Cisco D9800 Configuration Manual

Network transport receiver.
Hide thumbs

Advertisement

Configuring the Transport Stream Information
This section describes how to set up and configure the transport stream outputs in the D9800 Network
Transport Receiver.

Transport Stream Outputs

The ASI and MPEGoIP transport outputs are individually configurable and provide the capability of carrying
a decrypted program for digital tier distribution. This helps the compressed video programs are efficiently
distributed to households equipped with digital set-top boxes. Digital Program Insertion (DPI) information
will also be available along with the video and audio PIDs (Packet Identifiers) for external ad insertion in
compressed digital format.
Cisco D9800 Network Transport Receiver Version 3.01 Installation and Configuration Guide
1

Advertisement

   Also See for Cisco D9800

   Related Manuals for Cisco D9800

   Summary of Contents for Cisco D9800

  • Page 1: Table Of Contents

    Configuring the Transport Stream Information This section describes how to set up and configure the transport stream outputs in the D9800 Network Transport Receiver. • Transport Stream Outputs, page 1 • Configuring the ASI or MPEGoIP Output General Settings, page 3 •...

  • Page 2

    Configuring the Transport Stream Information DVB-ASI Output DVB-ASI Output The D9800 receiver has one DVB-ASI output. This output can be used as an input for a DVB-T transmitter or other types of DVB-ASI reception equipment. MPEGoIP Output The MPEGoIP output provides a number of output modes including the capability of carrying a decrypted program for digital tier distribution.

  • Page 3: Configuring The Asi Or Mpegoip Output General Settings

    Configuring the ASI or MPEGoIP Output General Settings Step 1 Do one of the following: • Web GUI (single-stream unit): From the D9800 web GUI, choose Transport Stream > ASI Output or MPEG over IP. Cisco D9800 Network Transport Receiver Version 3.01 Installation and Configuration Guide...

  • Page 4: Configuring The Asi Or Mpegoip Output Mode

    Configuring the Transport Stream Information Configuring the ASI or MPEGoIP Output Mode • Front Panel (single-stream unit): From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > ASI or MOIP. • Web GUI (multi-stream unit): From the D9800 web GUI, choose Transport Stream > ASI 1 Output, ASI 2 Output, IP Data 1/Data 2 Output, or IP Data 3/Data 4 Output.

  • Page 5

    Configuring the ASI or MPEGoIP Output Mode • Front Panel (multi-stream unit): From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > ASI or IP, and choose the input you want to configure general settings from the ASI or IP front panel menu.

  • Page 6

    In a multi-stream unit, this applies to a single input mode only. For more information on the single input mode, see Assigning a Channel to a Program Entry. In a multi input mode, Chg by Unplink (MS Mode) status is displayed. Cisco D9800 Network Transport Receiver Version 3.01 Installation and Configuration Guide...

  • Page 7: Configuring The Mpe Settings

    Note (D9800-SS-MPEGOIP). Step 1 From the D9800 web GUI, choose System Settings > MPE. Or, from the Main Menu of the D9800 front panel, choose Setup > IP > Protocols. Step 2 From the MPE Data Filter Mode drop-down list or the MPE front panel menu, choose whether the MPE data is forwarded to the network.

  • Page 8: Setting Up Redundancy Controls For Mpeg Over Ip And Mpe Outputs

    • Web GUI (single-stream unit): From the D9800 web GUI, choose Transport Stream > MPEG over IP Output, or choose System Settings > MPE. • Web GUI (multi-stream unit): From the D9800 web GUI, choose Transport Stream > IP Data 1/Data 2 Output or IP Data 3/Data 4 Output.

  • Page 9: Synchronizing The Output Services

    Step 1 Do one of the following: • Web GUI (single-stream unit): From the D9800 web GUI, choose Transport Stream > Digital Program Mapping for ASI or MPEG over IP. • Web GUI (multi-stream unit): From the D9800 web GUI, choose Transport Stream > Digital Program Mapping for ASI 1 Output, ASI 2 Output, IP Data 1/Data 2 Output, or IP Data 3/Data 4 output.

  • Page 10

    Configuring the Transport Stream Information Synchronizing the Output Services • Front Panel: From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > DPM. Step 2 In the DPM Program Entry Setup area, do one of the following: •...

  • Page 11

    • Web GUI (single-stream unit): From the D9800 web GUI, choose Transport Stream > ASI Output or MPEG over IP Output and refer to the Auto Sync area. • Front Panel (single-stream unit): From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > ASI or MOIP.

  • Page 12

    Setting up the Resynchronize All Option • Front Panel: From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > Options, and choose the input you want to configure from the Output front panel menu.

  • Page 13: Resolving Conflicts

    • Web GUI (single-stream unit): From the D9800 web GUI, choose Transport Stream > Digital Program Mapping for ASI or MPEG over IP output, and refer to the DPM General Settings area. • Front Panel (single-stream unit): From the D9800 front panel, choose Setup > Outputs > TS Out > DPM > ASI or MOIP.

  • Page 14

    ASI 1 Output, ASI 2 Output, IP Data 1/Data 2 Output, or IP Data 3/Data 4 Output, and refer to the DPM General Settings area. • Front Panel (multi-stream unit): from the D9800 front panel, choose Setup > Outputs > TS Out > DPM > ASI1 , ASI2, IP1/2, or IP3/4.

  • Page 15

    • Web GUI (single-stream only): From the D9800 web GUI, choose Transport Stream > Digital Program Mapping for ASI, MPEG over IP output, and refer to the DPM General Settings area. • Front Panel (single-stream only): From the D9800 front panel, choose Setup > Outputs > TS Out > DPM > ASI or MOIP.

  • Page 16

    • PAT, CAT, PMT, SDT - Regen • TSDT, NITO, SDTO, BAT, EIT, ECM, EMM, DRT, CDT - Drop • TDT, RST, TOT, DIT, SIT - Pass • NIT - Regen or Drop Cisco D9800 Network Transport Receiver Version 3.01 Installation and Configuration Guide...

  • Page 17: Copying Between Asi And Mpegoip Dpm Settings

    • Web GUI (multi-stream unit): From the D9800 web GUI, choose Transport Stream > Digital Program Mapping for ASI 1 Output, ASI 2 Output, IP Data 1/Data 2 Output, or IP Data 3/Data 4 Output. • Front Panel: From the D9800 front panel, choose Setup > Outputs > TS Out > DPM > Global. Step 2 For a single-stream unit, do one of the following: •...

  • Page 18

    Configuring the Transport Stream Information Configuring the Program Entries • Front Panel (single-stream unit): From the D9800 front panel, choose Setup > Outputs > TS Out > DPM > ASI or MOIP • Web GUI (multi-stream unit): From the D9800 web GUI, choose Transport Stream > Digital Program Mapping for ASI 1 Output, ASI 2 Output, IP Data 1/Data 2 Output, or IP Data 3/Data 4 Output.

  • Page 19

    From the D9800 web GUI, choose Transport Stream > Digital Program Mapping for ASI 1, ASI 2, IP Data 1/Data 2, or IP Data 3/Data 4. Or, from the D9800 front panel, choose Setup > Outputs > TS Out > DPM > ASI1, ASI2, IP1/2, or IP3/4.

  • Page 20

    Configuring the Transport Stream Information Mapping the Program PIDs • Front Panel (single-stream unit): from the D9800 front panel, choose Setup > Outputs > TS Out > DPM > ASI1, ASI2, IP1/2,or IP3/4. Step 2 Click the program entry radio button you want to map the PIDs and click Edit or choose the program entry from the PE front panel menu.

  • Page 21: Setting The Sap Ip Address

    • Web GUI (single-stream unit): From the D9800 web GUI, choose Transport Stream > MPEG over IP Output. • Front Panel (single-stream unit): From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > MOIP > MOIP Streams.

  • Page 22: Configuring The Forward Error Correction Settings

    Configuring the Transport Stream Information Configuring the Forward Error Correction Settings • Front Panel (multi-stream unit): From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > IP > Streams Configuration. Step 2 In the Maximum Transport Packets/Ethernet Frame field, or the TS/IP front panel menu, enter or choose the maximum number of transport packets per IP packet (1 to 7).

  • Page 23

    Configuring the Transport Stream Information Configuring the Forward Error Correction Settings Cisco D9800 Network Transport Receiver Version 3.01 Installation and Configuration Guide...

  • Page 24

    FEC Rows UDP Port field (or the FEC2 UDP front panel menu). The range is from 2 to 65534, even number only. We recommend that you set the port number to TS UDP port +4. Step 7 Click OK and apply the changes. Cisco D9800 Network Transport Receiver Version 3.01 Installation and Configuration Guide...

  • Page 25: Configuring Mpeg Over Ip Or Ip Data Streams

    • Web GUI (single-stream unit): From the D9800 web GUI, choose Transport Stream > MPEG over IP Output > Stream tab. • Front Panel (single-stream unit): From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > MOIP > MOIP Streams.

  • Page 26: Configuring The Transcoder Settings

    Configuring the Transport Stream Information Configuring the Transcoder Settings • Front Panel (single-stream unit): From the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > MOIP > MOIP Streams. • Web GUI (multi-stream unit): From the D9800 web GUI, choose Transport Stream > IP Data 1/Data 2 Output or IP Data 3/Data 4 Output >...

  • Page 27

    If desired, set a program channel for the second transcoder channel (PE2) and repeat Step 2, depending on the transcoding licenses. For more information on assigning a program channel to a PE, see Assigning a Channel to a Program Entry. Cisco D9800 Network Transport Receiver Version 3.01 Installation and Configuration Guide...

  • Page 28

    Configuring the HD and SD Transcode Settings Step 1 From the D9800 web GUI, choose Transport Stream > Transcoder Setup. Or, from the Main Menu of the D9800 front panel, choose Setup > Outputs > TS Out > Transcode. Step 2 Click the Transcoder 1, 2, 3, 4, 5, 6, 7, or 8 Output radio button to select the channel you want to configure, and click Transcoder Config.

  • Page 29

    Inserting Subtitles to Transcoded Video Step 1 From the D9800 web GUI, choose Transport Stream > Transcoder Setup. Step 2 Click the radio button of the channel you want to insert subtitles to transcoded video (Transcoder 1, 2, 3, 4, 5, 6, 7, or 8 Output), and click Subtitle Burn-In.

  • Page 30

    Step 1 From the D9800 web GUI, choose Transport Stream > Transcoder Setup, and click Apply Inband Settings. Or, from the main menu of the D9800 front panel, choose Setup > Outputs > TS Out > Transcode > Inband. Step 2 Check the transcoder/program entry check box that you want to apply uplink parameters, or choose the program entry from the PE front panel menu and then choose Yes or No from the Apply Inband front panel menu.

Comments to this Manuals

Symbols: 0
Latest comments: