Safeway EXECUTIVE Installation Instructions

A : TO THREAD SHOULDER STRAP
1. Insert "free" end of shoulder strap from underneath right hand side of the EXECUTIVE CAR SAFETY SEAT through slot in seat. Pull
through until 2-Slot slider touches the bottom of the seat.
2. Thread "free" end of shoulder strap through right hand buckle mechanism from underneath buckle through to top. Insert strap
through desired right side shoulder slot (according to height of child's shoulders)(Diagram 8)
3. Thread "free" end of shoulder strap through loop of adjustor strap
front of seat. (Diagram 9)
4. Thread through left side of buckle mechanism from top to bottom, insert through left hand side slot on bottom of the EXECUTIVE
CAR SAFETY SEAT (Diagram10).
5. Push belt underneath bottom of chair between seat and reclining mechanism and thread the belt through the 2-Slot slider (Diagram
11).
6. In order to ensure the belt is secure, thread "free" end of belt through the first slot of the 2-Slot slider once again
B : TO THREAD ADJUSTOR BELT
1. Adjust the EXECUTIVE CAR SAFETY SEAT to the sleeping position. Push the adjustor strap (small belt) between the shell and the
base towards the front of the chair. Thread the adjustor belt through the 2-Slot slider of the crotch strap towards the top of the
EXECUTIVE CAR SAFETY SEAT (Diagram 13). Thread the adjustor strap through the adjustor buckle and pull through(Diagram
14).
Once you have selected the correct shoulder height and re-thread the belts, the belt can be adjusted by a simple adjustment of the
adjustor belt in front (Diagram 14). Push the "adjustor buckle" and pull the harness to tighten or pull on the harness to loosen. You should
be able to comfortably fit your hand beneath the harness for an ideal fit with child strapped in the EXECUTIVE CAR SAFETY SEAT. The
"adjustor buckle" holds the harness in a fixed position.
HOW TO REMOVE AND FIT THE HEADREST
To remove the headrest, disengage the locking clip situated at the back of the EXECUTIVE CAR SAFETY SEAT, where the headrest
support legs slot into the backrest (Diagram 15). You can now pull the headrest out.
To fit the headrest, simply slide the headrest support legs into the eyelets situated at the top of the EXECUTIVE CAR SAFETY SEAT's
cover and into the holes in the backrest. Push the headrest down as far as possible. Replace the locking clip, making sure that it
engages.
HOW TO CLEAN THE EXECUTIVE CAR SAFETY SEAT AND COVER
All parts of the EXECUTIVE CAR SAFETY SEAT can be cleaned with mild cleaning agents.
Should you wish to remove the cover, the harness can be removed as follows :
1. Unbuckle the harness and separate the shoulder belt from the 2-Slot slider at the bottom of the EXECUTIVE CAR SAFETY SEAT.
2. Slide the entire strap free.
3. Remove cover.
4. The cover can be washed in luke warm water with a mild detergent. Do not tumble dry or use any solvents.
To replace the harness on the EXECUTIVE CAR SAFETY SEAT refer to
IMPORTANT POINTS TO REMEMBER
1. The safety of the EXECUTIVE CAR SAFETY SEAT is only valid If instructions are carefully followed. Keep instructions where they
can be readily found.
2. Ensure that the EXECUTIVE CAR SAFETY SEAT BELTS and the vehicle safety belts are in optimum condition before use. Ensure
that all belts are tightly fastened.
3. Ensure that the EXECUTIVE CAR SAFETY SEAT is fastened in the vehicle even when not in use.
4. Never leave a child unattended in the EXECUTIVE CAR SAFETY SEAT.
5. Do not use the EXECUTIVE CAR SAFETY SEAT if it has previously been involved in a collision.
6. Never leave heavy objects on the rear parcel shelf, they could injure your child if you brake sharply.
7. Ensure that your child does not accidentally unfasten the safety belt while playing.
8. Do not use the EXECUTIVE CAR SAFETY SEAT for children weighing more than 18 kg.
9. The seat cover or belts should not be replaced with any other than the one recommended by the manufacturer as they constitute an
integral part of the restraints' performance.
10. Do not use the EXECUTIVE CAR SAFETY SEAT with a 2-Point safety belt.
11. The EXECUTIVE CAR SAFETY SEAT when used as a GROUP 0 "rearward facing" must not be used in the front passenger seat
where the vehicle is equipped with a passenger seat air bag.
12. Ensure that if the EXECUTIVE CAR SAFETY SEAT has been exposed to direct sunlight, no part of it has become excessively hot.
13. The buckle has been purposely designed to provide a quick release. In the event of an emergency, it may be necessary for a person
unfamiliar with the equipment to release the child in seconds. The buckle has been designed therefore, so that even a child can
undo it. This means the buckle is not tamper proof. The child transported in the safety seat should be disciplined to not play with the
buckle while the harness is in use.
14. Ensure that the EXECUTIVE CAR SAFETY SEAT does not become trapped by a moveable car seat or in the door of the car.
15. SET THE RIGHT EXAMPLE, ALWAYS BUCKLE UP.
16. Do not hesitate to contact us if you have any queries on your EXECUTIVE CAR SAFETY SEAT.
Distributed by: Unimark Distributors (Pty) Ltd., P.O. Box 912-1095, Silverton, 0127
Tel : +27 12 804-1793, Fax : +27 12 804-1795, E-mail : unimark@iafrica.com
, thread through left hand side shoulder slot from rear through to
(Diagram 12).
HOW TO ADJUST HARNESS AND THREAD BELTS
EXECUTIVE
EXECUTIVE
CAR SAFETY SEAT

INSTALLATION INSTRUCTIONS

.
Group 0 : 0 - 10 kg
Group 1 : 10 - 18 kg