Table of Contents
Advertisement
Quick Links
BRUSHLESS 1/2"
HAMMER DRILL
241-0465
OPERATOR'S MANUAL
CAUTION:
To Reduce The Risk Of Injury, User Must Read And
Understand Operator's Manual. Save These Instructions For Future
Reference.
For questions / comments, technical assistance or repair parts –
Please Call Toll Free: 1-866-917-4374. (M-F 8:30am-5:00pm Est.)
Advertisement
Table of Contents
Related Manuals for MasterForce 241-0465
Summary of Contents for MasterForce 241-0465
- Page 1 BRUSHLESS 1/2” HAMMER DRILL 241-0465 OPERATOR’S MANUAL CAUTION: To Reduce The Risk Of Injury, User Must Read And Understand Operator’s Manual. Save These Instructions For Future Reference. For questions / comments, technical assistance or repair parts – Please Call Toll Free: 1-866-917-4374. (M-F 8:30am-5:00pm Est.)
-
Page 2: Table Of Contents
TABLE OF CONTENTS Safety Symbols ............Page 2 Safety Instructions . -
Page 3: Safety Symbols
SAFETY SYMBOLS Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely. Symbol Designation / Explanation Name Volts Voltage... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are not substitutes for proper accident prevention measures. - Page 5 SAFETY INSTRUCTIONS GENERAL POWER TOOL SAFETY 5. When operating a power tool outdoors, use an extension cord suitable for WARNINGS outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric WARNING: Read all safety shock. warnings and all instructions.
-
Page 6: Hammer Drills
SAFETY INSTRUCTIONS POWER TOOL USE AND CARE 2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of 1. Do not force the power tool. Use the injury and fire. correct power tool for your application. - Page 7 SAFETY INSTRUCTIONS 4. Hold power tool by insulated gripping WARNING: Some dust created by surfaces, when performing power sanding, sawing, grinding, drilling operation where the cutting accessory and other construction activities contains may contact hidden wiring. Cutting accessory contacting a “live” wire may chemicals known to the state of California make exposed metal parts of the power to cause cancer, birth defects or other...
-
Page 8: Overview/Specifications
OVERVIEW Side Handle Torque-Adjustment Ring Clutch Mode-Selector Ring Two-Speed Gearbox Switch Chuck Sleeve Direction-of-Rotation Variable-Speed Selector (Forward/ Trigger Switch Center-Lock/Reverse) Bit Holder LED Worklight Belt Clip SPECIFICATIONS No-load Speed 0-500/ 0-1,850 RPM Impact Rate 0-6,500/ 0-24,050 BPM Torque 700 in.lb. Chuck Size 1/2 in. -
Page 9: Assembly
ASSEMBLY CONTENTS WARNING: If any part is broken or missing, DO NOT attempt to plug in the Brushless hammer drill, belt clip, bit holder, power cord or operate the tool until the bit, side handle and instruction manual. broken or missing part is replaced. Failure to do so could result in possible serious UNPACKING injury. - Page 10 ASSEMBLY TO ATTACH BATTERY PACK 1. Lock the trigger switch on the hammer drill by placing the direction-of-rotation (FIG. 1) selector in the center position. 2. Rotate chuck sleeve 1. Lock the trigger switch on the hammer counterclockwise when viewed from drill by placing the direction-of-rotation chuck end, and open the chuck to the selector in the center position.
- Page 11 ASSEMBLY INSTALLING AND REMOVING FIG. 4 THE BELT CLIP (FIG. 3) To install the belt clip: Screw 1. Remove the battery from the tool. 2. Align the rib of the clip with the hole on the base of the hammer drill. 3.
- Page 12 OPERATION VARIABLE-SPEED TRIGGER DIRECTION-OF-ROTATION SWITCH (FIG. 6) SELECTOR (FIG. 7) 1. To turn the hammer drill ON, press the The direction of bit rotation is reversible and trigger switch. is controlled by a selector located above the 2. To turn the hammer drill OFF, release the trigger switch.
-
Page 13: Operation
OPERATION TWO-SPEED GEARBOX SWITCH MODE SELECTION (FIG. 9) (FIG. 8) Your tool has three operating modes: drilling with hammering action, drilling only, and Your tool is equipped with two separate driving screws. -To set the operating mode, speed ranges: speed 1 (low speed) and rotate the mode-selector ring and torque- speed 2 (high speed). - Page 14 OPERATION ADJUSTABLE CLUTCH (FIG. 10) LED WORKLIGHT (FIG. 11) Your tool is equipped with a light that Your tool features 24 clutch settings. Out- turns on automatically when the switch is put torque will increase as the torque-ad- activated to provide better visibility when justment ring is rotated from 1 to 24.
-
Page 15: Wood Drilling
OPERATION MASONRY DRILLING 8. If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Remove the bit from the workpiece and For maximum performance, use high-speed determine the reason for jamming. steel bits for masonry drilling. 1. -
Page 16: Maintenance
MAINTENANCE CHUCK REMOVAL (FIG. 13) WARNING: To avoid serious personal injury, always remove the battery The chuck can be removed and replaced pack from the tool when cleaning or with a new one. performing any maintenance. 1. Lock the trigger switch by placing the direction-of-rotation selector in the WARNING: When servicing, use... -
Page 17: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE SOLUTION The hammer drill does not work. The battery is depleted. Charge the battery. The bit cannot be installed. The sleeve is not released. Release the sleeve. The bit does not fit the Use a suitable bit. sleeve. - Page 18 NOTES Page 17...
-
Page 19: Warranty
90-DAY MONEY BACK GUARANTEE: This MASTERFORCE brand power tool carries our 90-DAY Money Back ® Guarantee. If you are not completely satisfied with your MASTERFORCE brand ® power tool for any reason within ninety (90) days from the date of purchase, return... - Page 20 © 2016 Menard, Inc., Eau Claire, WI 54703 12/2016...
Need help?
Do you have a question about the 241-0465 and is the answer not in the manual?
Questions and answers
Sounds like gears are stripped