Advertisement
Quick Links
LANCOM LN-860
LANCOM LN-862
Quick Reference Guide
4
DC 12 V
a
b
Please observe the
following when setting
up the device
WLAN 1 Ant 2
WLAN 2 Ant 2
A For devices to be
operated on the
desktop, please attach
the adhesive rubber
footpads
A Do not rest any objects
WLAN 1 Ant 1
WLAN 2 Ant 1
on top of the device
A Keep the ventilation
slots on the side of
the device clear of
obstruction
a
b
A Lockable wall and
ceiling mounting with
Wi-Fi antennas (only LN-862)
Power
the LANCOM Wall
Screw the supplied Wi-Fi antennas
When connecting the cable to the
Mount (LN) (available as
onto the connectors
device, turn the bayonet connector
an accessory)
WLAN 1 Ant 1 / Ant 2 and
90° clockwise until it clicks into
WLAN 2 Ant 1 / Ant 2.
place.
The desired MIMO behaviour can
be configured under
> Physical WLAN Settings
> Radio
> Antenna grouping
Use only the supplied power adapter!
ETH1 (PoE)
Reset
Config (Com)
c
d
c
d
Ethernet interface
Serial interface
Use the cable with the Ethernet
You can configure the device by
connectors to connect interface
connecting it to a PC with a
ETH1 (PoE) or ETH2 to your PC
configuration cable
or a LAN switch.
(separately available).
5
Please note that when operating both Wi-Fi modules in the same frequency band, mutual
interference cannot be ruled out
a
b
a
b
Power
WLAN link
Off
Device switched off
Off
No Wi-Fi network defined or Wi-Fi module
deactivated. The Wi-Fi module is not
Green,
Device operational
transmitting beacons.
constantly on*
resp. device paired / claimed and LANCOM
Management Cloud (LMC) accessible.
Green
At least one Wi-Fi network defined and
Wi-Fi module activated. The Wi-Fi module
Red/green
Configuration password not set. Without a
is transmitting beacons.
blinking
configuration password, the configuration
data in the device is unprotected.
Green
Number of flashes = number of connected
inverse flashing
Wi-Fi stations and P2P wireless
Orange/green
At least one Wi-Fi module is in
connections, followed by a pause (default).
blinking alternately
managed mode and has not found a
with the WLAN
WLAN controller yet. The corresponding
Alternatively the flashing frequency can
link LED
Wi-Fi module(s) is/are switched off until a
indicate signal strength over the defined
WLAN controller has been found to supply
P2P link or the signal strength between the
access point and the device operating in
a configu ration, or until being switched
client mode.
manually into another operating mode.
Green blinking
DFS scanning or other scan procedure.
Orange/red
At least one Wi-Fi module is in managed
blinking alternately
mode and has found a WLAN controller.
Red blinking
Hardware error in the Wi-Fi module.
with the WLAN
However, the WLAN controller cannot
link LED
assign a configuration because the
firmware and/or the device's loader
version is not compatible with the WLAN
controller.
1x green inverse
Connection to the LMC active, pairing OK,
blinking*
claiming error.
2x green inverse
Pairing error, resp.
blinking*
LMC activation code / PSK not available.
3x green inverse
LMC not accessible, resp.
blinking*
communication error.
Hardware
Power supply
12 V DC, external power adapter (110 or 230 V) with bayonet connector to secure against
disconnection or PoE based on 802.3at via ETH1
Power consumption
Approx. 15.1 W via 12 V / 2 A power adapter (value refers to the total power consumption of
access point and power adapter),
Approx. 14.9 W via PoE (value solely refers to the power consumption of the access point)
Environment
Temperature range 0–45 °C (vertical wall mount with LANCOM Wall Mount (LN)),
0-37 °C (horizontal ceiling mount with LANCOM Wall Mount (LN))
Access point overheating is avoided by automatic throttling of the Wi-Fi modules
Humidity 0-95 %; non-condensing
Housing
Robust synthetic housing, rear connectors, ready for wall and ceiling mounting; measures
205 x 42 x 205 mm (W x H x D)
Number of fans
None; fanless design, no rotating parts, high MTBF
Wi-Fi
Frequency band
2400-2483.5 MHz (ISM) or 5180-5700 MHz (restrictions vary between countries)
Radio channels 2.4 GHz Up to 13 channels, max. 3 non-overlapping (2.4 GHz band)
Radio channels 5 GHz
Up to 19 non-overlapping channels (automatic dynamic channel selection required)
Interfaces
ETH1 (PoE)
10 / 100 / 1000 Base-TX, autosensing, auto node hub,
PoE adapter compliant with IEEE 802.3at required
ETH2
10 / 100 / 1000 Base-TX, autosensing, auto node hub
Serial interface
Serial configuration interface / COM-port (8-pin mini-DIN): 9,600 - 115,000 baud
Declaration of conformity
The Declaration of Conformity can be found on the product page of our website www.lancom-systems.com
Package content
Manual
Installation Guide (DE/EN), Quick Reference Guide (DE/EN)
Antennas (only LN-862) Four 3 dBi dipole dual-band antennas
Cable
Ethernet cable, 3 m
Power adapter
External power adapter, NEST 12 V / 1.5 A DC/S, barrel connector 2.1 / 5.5 mm bayonet,
LANCOM item no. 111507 (EU, 230 V); LANCOM item no. 111302 (UK, 230 V)
*) The additional power LED status are displayed in 5-seconds rotation if the device is configured to be managed by the
LANCOM Management Cloud.
Advertisement
