Hisense Babysense 5s User Manual

5
the monitor detects less than 10 micro-
S
movements per minute. The system's non-touch
sensor pads under the mattress monitor baby's
Infant Movement Monitor
movement without restraining him.
Warnings
Ensure you read this user guide before installing and
1. Insert, in accordance with the markings, 4 new and
using the product.
identical size AA 1.5 volt batteries, preferable alkaline.
Babysense is a high quality, high sensitivity
Close the battery cover.
electronic device which must be handled with care:
• Do not handle roughly, drop or throw. Note: Do not mix old and new batteries.
• Follow the installation instructions carefully to Note: For replacing the batteries, remove the battery
ensure that it is installed securely and correctly.
cover by inserting a flat screwdriver into the opening
• Babysense is not a toy. Do not allow children of any
recess (see illustration 7).
age to play with it.
Note: Please dispose of used batteries in accordance
• Do not put any additional baby or pet in the bed.
with local waste regulations.
Babysense cannot be used for two infants in one bed.
• You must undertake the performance test daily of 2. Place the control unit holder on the base of the
the Babysense monitor (as set out on page 3). crib or bed and in between two bars as shown in
illustration 1.
• Do not operate a vaporiser or ventilator directly
towards the bed.
• To avoid possible danger from sensor cords,
ensure that excess cords are pulled back under
the mattress, secured with the included cable tie
and are not visible or reachable.
• Install 4 new and identical size AA 1.5 volt batteries,
preferably alkaline.
• IMPORTANT: It is strongly advised that every
caregiver learn how to give first aid.
Please note
Babysense monitors and alerts, but cannot prevent
Sensor
any type of distress. The responsibility for assistance and
applying first aid rests on caretakers, who must personally
check the baby as often as necessary. Babysense senses
movements and motion only, and cannot
monitor other occurrences. The purpose of the device
is to alert when stopping or slowing of movement
3. Sensor pad installation:
occur.
Babysense is a unique safety and reassurance system • When using for an infant not yet able to crawl, place
which helps give parents peace of mind, alerting if one sensor pad as shown in illustration 2. Make sure the
movements stop or become irregularly slow, giving
sensor is placed underneath the baby's position in the
critical time to intervene. There are a number of
crib.
cautionary steps which are internationally
recommended for SAFE SLEEPING:
• When the baby begins to crawl, and is able to move
* Always lay your baby to sleep on his or her back.
onto areas not "covered" by a single sensor pad, attach
* Refrain from smoking near or around your baby.
the second sensor and place the two sensors as shown
* Avoid over-heating of the baby's surroundings.
in illustration 2.
* Do not leave any objects near your baby that can
cause suffocation.
PLEASE NOTE: The sensors shall be placed with the
Babysense is an addition to these precautions.
marking "THIS SIDE UP" facing upwards.
Babysense is a movement monitor for home use,
intended for basically healthy infants up to one year
of age, and is not to be relied on for use with premature
or high-risk infants requiring constant medical supervision.
Principal Of Operation
Babysense continually detects the baby's motion
and movements, and will set off a sound and visual
alarm if movement stops for 20 seconds or if
1
Sensor pads
(Under mattress)
Installation
Control unit
Top crib/bed view
For babies not
yet able to crawl
Control unit holder
4. When using a crib/bed equipped with spring
base, place extra wooden board (plywood) under
each sensor pad, as shown in illustration 3. The
recommended size of the board is at least 17'' x 11''
and 1/2'' thick.
Top crib/bed view
Cables Sensor
I
llustration 1
Sensor
Plywood
5. Pass the cord(s) of the sensor pad(s) through
special openings in the holder. (see illustration 4)
Control unit
holder
I
llustration 4
User Guide
6. Attach end(s) of the cord(s) to the outlets
marked "SENSOR" on the back of control unit
(see illustration 6 and 7). When using one sensor
pad, attach to either "SENSOR" outlet.
PLEASE NOTE: Do not attach any cable to the
blocked socket, marked "DO NOT USE"
Control
I
Unit llustration 5
Cable Cable
Top crib/bed view
Bed/Crib
For crawling babies base
Control unit holder
I
llustration 2
Slot
Sensor | Do not use | Sensor
Spring base
Sensor | Do not use | Sensor
Sensor
Hanging hook
I
llustration 6
Slot
I
llustration 7
"Sensor"
I sockets
llustration 3
Sensor | Do not use | Sensor
Blocked socket
DO NOT USE
Opening
recess
Battery
Cables cover
Speaker
2
• Acoustic and visual red light alarms are activated
7. Should the design of the crib/bed not allow proper
if the baby's movement stops or slows significantly.
installation with the control unit holder, please use the
• If the red low-battery warning light flashes,
optional hanging hook (see illustration 6) and hang the
replace all batteries as soon as possible. If in
control unit from the bottom edge of the crib.
addition clicking is heard, all batteries must be
replaced immediately.
8. Press the control unit holder or hanging hook firmly
• Turn off by pressing the On/Off button before
into the slot in the back of the control unit (see
taking your baby out of crib/bed.
illustration 5 and 6).
Place the mattress firmly on top of the sensor
9.
pads. If the mattress cannot be in contact with the
Babysense is a highly sensitive device which
sensor pads, or if the bed base is soft, padded or
monitors a baby's motion and movements through
contains springs, place extra plywood on the bed
the mattress during sleep. There are two main
base, place the sensor pads on the plywood and
causes of malfunction - technical malfunctions and
place the mattress firmly on top (see section 4).
malfunctions due to environmental factors.
IMPORTANT: To avoid possible danger from sensor
cords, ensure that excess cords are pulled back
under the mattress, secured with the included cable
tie and are not visible or reachable.
In order to minimize technical problems, follow
installation and operation instructions carefully.
Layout of control unit
Environmentally caused malfunction
See illustration 8 for layout of control unit featuring:
• On/Off button. Due to the high sensitivity of Babysense, it can be
• Blue movement indicator light. influenced by fans, wind, air conditioning,
• Acoustic and visual red alarm light. vibrating household sources and so forth. Such
• Low battery red warning light.
environmental effects could be picked up by the
sensors on a similar level to that of slight movements,
thus preventing or delaying alarm activation.
Conduct this performance test daily
Blue movement
Red alert
indicator light
alarm light
Do not conduct the performance test by picking up
Red low battery
baby out of bed and waiting for the alarm to sound
warning light On/Off
button
• The performance test should be conducted
while the baby is not in bed.
• Turn the unit on and take two steps back from bed.
• Ensure the alarm goes off within 20 seconds
(due to absence of movement).
• The alarm may sound with or without
preliminary ticking.
Speaker
• Check the alarm can be heard in all locations
throughout the home or place of care.
• If the alarm does not sound within 20
I
llustration 8
seconds refer to the troubleshooting at page 4.
• The performance test must be conducted daily.
Operation
Isolated cases of false alarms are possible. Check if caused
Babysense is ready for operation and use once the
by faulty connection of the sensor pad(s) to the control
installation is complete. To operate, follow the
unit, connection of only one sensor pad when the
below instructions:
baby is can move off the immediate area, connection
• Place your baby in the crib/bed.
of two sensor pads far apart from each other when the
• Press the On/Off button to turn on the control unit.
baby is not crawling yet, or failure of the sensor pads to
• Red lights switch on briefly and a double click
be directly against the mattress.
sound is heard.
• When any movement is sensed, the blue light
In case of false alarms, refer to the troubleshooting
flashes.
guide. If the problem cannot be solved, please
contact your nearest BABYSENSE representative.
3
Testing Operation
Technical malfunction
False alarms