Advertisement
ADJUSTMENTS
1
Area depth angle adjustment
Depth angle
adjustment screw
for the Presence/Motion
area
When adjusting the 2nd row close to the door,
follow Table1 dipswitch18(Installation mode) for the easier adjustment.
When dipswitch 18 is set to "ON", sensor automatically set back to the operation mode after 5 minutes.
If the installation mode is required again, set dipswitch 18 to "OFF", then set to "ON".
Make sure that the detection area does not overlap with the door / header, and there is no highly reflecting
NOTE
object near the detection area otherwise ghosting / signal saturation may occur.
1-1 Presence/Motion area
Depth angle adjustment screw
Shallow
for the Presence/Motion area.
-2°
0°
-6°
+4°
Use the area adjustment tool (A)
as shown above
-10°
+8°
to change the area depth angle.
Deep
Shallow
[feet,inch(mm)]
[feet,inch(mm)]
0
0
3'3"
3'3"
(1000)
(1000)
6'6"
6'6"
(2000)
(2000)
9'10"
9'10"
(3000)
(3000)
6'6"
3'3"
0
3'3"
0
3'3"
(2000)
(1000)
(1000)
(1000)
2
Area width adjustment
2-1 Presence/Motion area
Adjust the Presence/Motion area width
with the Width adjustment screws.
Each side can be adjusted independently, allowing for
asymmetrical settings. Use the area adjustment tool (A)
to adjust area width.
NOTE
When setting the Presense/Motion area width,
make sure to turn the width adjustment screws
until it clicks.
Opens
Opens
1
9
All Areas
All Areas
elimination
elimination
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
3
Presence/Motion
area rows adjustment
Presence/Motion area rows can be adjusted
by changing the Dipswitches 6 & 7.
See 5.Dipswitch settings, Table 1.
5
Dipswitch settings
The area adjustment tool (C) can be used to change Dipswitch.
Table1
Function
Dipswitch
60sec.
30sec.
1
Presence timer
Dipswitch
1
2
1
2
Dipswitch
Setting1
Setting2
3
Frequency
Dipswitch
3
4
3
4
OFF
ON
Dipswitch
BLUEZONE
5
5
Dipswitch
6
5rows
4rows
Presence/Motion
area row adjustment
6
7
Dipswitch
6
7
8 9 10
1
2
3
Dipswitch
8
Approach area
Dipswitch
9
width adjustment
Dipswitch
10
Normal
Rain
Dipswitch
Rain mode
11
11
Normal
Snow
Dipswitch
Snow mode
12
12
Bi
Dipswitch
Direction
13
13
OFF
Simultaneous
Dipswitch
14
output
14
Area adjustment tool
Depth angle
adjustment screw
for the Approach
area
1-2 Approach area
Depth angle adjustment screw
Deep
for the Approach area.
-5°
0°
-10°
5°
Use the area adjustment tool (A)
as shown above
-15°
+10°
to change the area depth angle.
Deep
Shallow
[feet,inch(mm)]
0
3'3"
3'3"
(1000)
(1000)
6'6"
6'6"
(2000)
(2000)
9'10"
9'10"
(3000)
(3000)
13'12"
9'10"
6'6"
6'6"
3'3"
0
(4000)
(3000)
(2000)
(2000)
1000
2-2 Approach area
Approach area width can be adjusted
by changing the Dipswitches 8,9,10.
See 5.Dipswitch settings, Table 1.
Left eliminated
Right eliminated
1 2 3
Width adjustment screws
1 2
8 9
1 2 3
elimination
elimination
elimination
8
9
1
2
3
4
5
6
7
8
9
1
2
4
Sensitivity adjustment
Adjust the Approach area and
Motion/Presence area with potentiometer.
Turning it clockwise increases the sensitivity and
turning counterclockwise lowers the sensitivity.
Presence/Motion
Approach sensitivity
sensitivity
Low
High
Use the area adjustment tool (B)
to change sensitivity.
Setting
Comment
180sec.
600sec.
To enable the presence detection, do not
enter the detection area for 10 seconds
after setting the timer.
2
1
2
1
2
Setting3
Setting4
When using more than one sensor close
to each other, set the frequency different
for each sensor.
4
3
4
3
4
When dipswitch 5 is set to "ON",
the BLUEZONE (1st row) is active and
looks through the threshold.
5
Rows can be eliminated as shown below.
5rows
4rows
3rows
2rows
7
6
7
6
7
4
5
6
7
8
1
8
2
7
3
6
4
5
The width of Approach area can be
Active area
adjusted by changing the Dipswitches as
Inactive area
shown the left.
Set this switch to "Rain" if the sensor is
used in a region with a lot of rain.
11
Set this switch to "Snow" if the sensor is
used in a region with snow or
a lot of insects.
12
When dipswitch 13 is set to "Uni",
Uni
*Please refer to
this setting enables the door to close
Table 2 for the
faster when a person walks away from
details.
13
the door.
When Dipswitch 14 is set to "ON", both
the activation & safety relay outputs will
ON
operate simultaneously regardless of
detection area.
14
But only the Safety output relay
will respond back with a Safety output
when it receives a Test input.
Safety output
Dipswitch
B
15
(to door controller)
Test input
Dipswitch
16
(from the door controller)
A
Dipswitch
C
Future use
17
Dipswitch
Installation mode
18
Table 2
Door
Shallow
Deep
Bi
Sensor
Detection
area
13
CHECKING
Check the operation in the operation mode according to the chart below.
[feet,inch(mm)]
0
Entry
Image
6'6"
3'3"
0
(2000)
(1000)
Status
Operation indicator
OFF
Activation
14
output
ON
14
N.O.
7 8 9
OFF
15
N.C.
14
15
Safety
output
N.O.
7 8 9
ON
elimination
15
N.C.
14
15
NOTE
The response time may differ according to the color of the objects and the color/material of the floor.
3
4
5
6
7
8
9
INFORM BUILDING OWNER / OPERATOR OF THE FOLLOWING ITEMS
WARNING
1. Always keep the detection window clean. If dirty, wipe the window with a damp cloth. Do not use any cleaner / solvent.
2. Do not wash the sensor with water.
3. Do not disassemble, rebuild or repair the sensor yourself, otherwise an electric shock may occur.
4. When the operation indicator blinks green, contact your installer or service engineer.
5. Always contact your installer or service engineer when changing the settings.
6. Do not paint the detection window.
1. When turning the power ON, always walk-test the detection area to ensure the proper operation.
NOTE
2. Do not place any objects that move or emit light in the detection area. (e.g. plant, illumination, etc.)
TROUBLESHOOTING
Operation
Door operation
indicator
None
Door does not
open when a
person enters
Unstable
the detection
area.
Proper
Door opens
Unstable
when no one
is in the
detection area.
(ghosting)
3rows
2rows
Proper
Door remains
Proper
open
Fast
Green
blinking
Slow
Green
blinking
Proper
Slow
operation
Green
blinking
Manufacturer
OPTEX Co.,LTD.
5-8-12 Ogoto Otsu 520-0101, Japan
TEL.: +81(0)77-579-8700
FAX.: +81(0)77-579-7030
WEBSITE:
www.optex.co.jp/as/eng/index.html
N.O.
N.C.
15
15
High
Low
16
16
OFF
ON
18
18
Bi-direction
Uni-direction
Uni
13
Outside of
Entry into
Power
Entry into
detection
Approach area
OFF
5th row
area
(6th row)
Approach
Motion
-
Stand-by
detection active
detection active
Green
Orange Blinking
Orange
None
Possible cause
Wrong power supply voltage.
Set to the stated voltage.
Wrong wiring or connection failure.
Check the wires and connector.
Wrong detection area positioning.
Check ADJUSTMENTS 1, 2 ,3 ,4 , 5.
Sensitivity is too low.
Set the sensitivity higher.
Short presence timer.
Set the presence timer longer.
Dirty detection window.
Wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Wrong wiring or connection failure.
Check the wires and connector.
Remove the objects.
Objects that move or
emit light in the detection area.
The detection area overlaps with
Check Table1 dipswitch 3 & 4.
that of another sensor.
Waterdrops on the detection window.
Use the rain-cover. (Separately available)
Or wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Or install in a place keeping the waterdrops off.
Detection area overlaps with door /
Adjust the detection area to "Deep"(Outside).
header.
Sensitivity is too high.
Set the sensitivity lower.
Raining or snowing
Set dipswitch 11, 12 to "Rain","Snow".
Wrong setting of dipswitches
Check Table 1 dipswitch 11, 12, 15.
Sudden change in the detection area.
Check ADJUSTMENTS 4 & Table 1 dipswitch 1, 2.
If the problem still persists, hard-reset the
sensor.(Turn the power OFF and ON again)
Wrong wiring or connection failure.
Check the wires and connector.
Dirty detection window
Wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Sensor failure
Contact your installer or service engineer.
Signal saturation
Remove highly reflecting objects from the detection
area. Or change the area depth angle.
The detection area overlaps with
Adjust the detection area to "Deep"(Outside).
the door / header.
Signal saturation (BLUEZONE)
Remove highly reflecting objects from the detection
area. Or change the area depth angle.
North and South America Subsidiary
OPTEX INCORPORATED
18730 S. Wilmington Avenue, Suite 100
Rancho Dominguez CA 90220 U.S.A
TEL.: +1-800-877-6656
FAX.: +1(310)898-1098
WEBSITE: www.optextechnologies.com
Select "N.O." / "N.C." for Safety output.
The delay time between Test input and
Safety output is 10msec..
Set dipswitch 18 to "ON" to adjust the 2nd
row. During the installation mode only the
2nd row remains active and the operation
indicator shows yellow. After setting the
row, switch dipswitch 18 "OFF".
: Detection
: Non-Detection
Entry into
Entry into
Entry into
Entry into
BLUEZONE
4th row
3rd row
2nd row
(1st row)
Presence
detection active
Red
Red
Blue
Blinking
Possible countermeasures
East coast office
8510 McAlpines Park Drive, Suite 108
Charlotte, NC 28211 U.S.A.
TEL.: +1-800-877-6656
FAX.: +1(704)365-0818
WEBSITE: www.optextechnologies.com
Advertisement
