Optex i-oneX T Manual

i-oneX T
MANUFACTURER'S STATEMENT
MANUFACTURER'S STATEMENT
Read this operation manual carefully before use to ensure proper operation of this product.
Failure to read this operation manual may cause improper operation and may result in serious injury or death of
a person.The meanings of the symbols are as follows.
Disregard of the warning symbol can cause improper operation which may cause death
WARNING
or serious injury.
Disregard of the caution symbol can cause improper operation which may cause injury of a
CAUTION
person or damage the object.
NOTE Special attention is required to the section of this symbol.
NOTE
1. This product is a non-contact switch intended for header mount or wall mount for use on an automatic sliding door.
Do not use for any other applications.
2. When setting the sensor's detection area, make sure that there is no traffic around the installation site.
3. Before turning the power ON, check the wiring to prevent damage or malfunction of equipment connected to
the product.
4. Only use the product as specified in the operation manual provided.
5. Be sure to install and adjust the sensor in accordance with the local laws and standards of the country in which
the product is installed.
6. Before leaving the installation site make sure that the product is operating properly and instruct the building
owner/operator on proper operation of the door and the product.
7.The product settings can only be changed by an installer or service engineer. When changed, the
changed settings and the date shall be registered in the maintenance logbook accompanying the door.
WARNING
Do not wash, disassemble, rebuild or repair the sensor, otherwise
it may cause electric shock or breakdown of the equipment.
Danger of electric shock
NOTE
The following conditions are not suitable for sensor installation.
-Fog or exhaust emission around the door
-Wet floor
-Vibrating header or mounting surface
-Moving objects, steel plate, emergency lights or illumination in the detection area or in vicinity
-Highly reflecting floor or highly reflecting objects around the door
SPECIFICATIONS
Model : i-oneX T
Cover color : Black
Mounting height : 6'7" to 9'10" (2.0m to 3.0m)
Detection area : See DETECTION AREA
Detection method : Active infrared reflection
Depth angle : Approach area -15° to +10°
adjustment Presence/Motion area -10° to +8°
Power supply : 12 to 24VAC ±10% (50 / 60 Hz)
12 to 30VDC ±10%
Power consumption : < 2.5W (< 4VA at AC)
Operation indicator : See Operation indicator table
Activation output : Form A relay
50V 0.3A Max.(Resistance load)
Test input : Opto coupler
Voltage 5 to 30VDC
Current 6mA Max.(30VDC)
Operation indicator table
Status Operation indicator color
Stand-by (installation mode) Yellow
Green
Stand-by (operation mode)
*1)
BLUEZONE (1st row) detection( Blue
2nd row detection Red blinking
3rd/4th row detection Red
Orange
5th row detection
Orange blinking
Approach (6th row) detection
Signal saturation Slow Green blinking
Sensor failure Fast Green blinking
NOTE
The specifications herein are subject to change without prior notice due to improvements.
*1 : See BLUEZONE AREA
OUTER DIMENSIONS AND PART NAMES
1' 5/16" (312)
9 13/16" (250)
4 13/16" (123)
4 15/16" (125)
1 7/16" (36)
(2)
(3)
(1)
(12)
(11)
(6)
(10)
(4) (8)
(5)
BLUEZONE AREA
When dipswitch 5 is set to "ON", the BLUEZONE area, that provides extra safety over the threshold, is activated.
In case the BLUEZONE function is not required, set dipswitch 5 to "OFF".
Do not set the 2nd row overlapping the threshold regardless of the setting of dipswitch 5.
4th row
3rd row
5th row 2nd row
Approach BLUEZONE
(6th row) (1st row)
All manuals and user guides at all-guides.com
Safety output : Form A relay
50V 0.3A Max.(Resistance load)
Output hold time : 0.5 to 1.5sec.
Response time : < 0.3sec.
Operating temperature : -31°F to 131°F(-35°C to +55°C)
Operating humidity : < 80%
IP rate : IP54
Weight : 14.6oz (420g)
Accessories : 1 Operation manual
2 Mounting screws
1 Mounting template
1 Area adjustment tool
1 Cable 9'10" (3m)
1sec. 1sec.
[inch (mm)]
2 1/16" (52.5)
(3) (2) (1) Connector
(11)
(2) Mounting holes (for retrofit)
(3) Mounting holes
(4) Operation indicator
(5) Width adjustment screws
(6) Depth angle adjustment screw (Presence/Motion)
(7) Depth angle adjustment screw (Approach)
(8) Sensitivity potentiometers
(7) (9) Dipswitches
(9)
(10) Detection window
(11) Cover fixing
(12) Area adjustment tool
4th row
3rd row
5th row
2nd row
Approach
BLUEZONE
(6th row)
(1st row)
2nd row overlapping
the threshold
DETECTION AREA
The chart shows the values at depth angle 0°
[feet,inch(m)]
A 7'3" (2.20) 8'2" (2.50) 9'10" (3.00)
B 9" (0.22) 10" (0.25) 1' (0.31)
C 6" (0.16) 7" (0.18) 8" (0.21)
D 2" (0.06) 3" (0.07) 3" (0.08)
E 7" (0.17) 8" (0.20) 9" (0.24)
BLUEZONE
(1st row)
F 1'7" (0.49) 1'10" (0.55) 2'2" (0.65)
2nd row
G 1'8" (0.50) 1'11" (0.58) 2'4" (0.70)
3rd row
H 2'8" (0.82) 3'1" (0.93) 3'8" (1.11) 4th row
5th row
I 2'10" (0.86) 3'3" (0.99) 3'11"(1.19)
Approach
J 3'5" (1.04) 3'10" (1.18) 4'8" (1.41)
(6th row)
K 3'7" (1.09) 4'1" (1.24) 4'11" (1.49)
L 4'9" (1.45) 5'5" (1.65) 6'6" (1.98)
M 8'1" (2.46) 9'2" (2.79) 11' (3.35)
N 4'6" (1.38) 5'2" (1.57) 6'2" (1.89)
O 7'1" (2.15) 8' (2.45) 9'8" (2.95)
P 8'4" (2.53) 9'5" (2.88) 11'4" (3.45)
Q 10'6" (3.20) 12' (3.65) 14'4" (4.38)
R 12'1" (3.68) 13'9" (4.18) 16'6" (5.02)
S 14' (4.27) 15'11" (4.86) 19'2" (5.84)
T 13'5" (4.10) 15'4" (4.67) 18'4" (5.60)
U 16'9" (5.10) 19' (5.79) 22'10" (6.95)
Approach area
*Mounting Height = 7'3"(2.2m)
[feet,inch(m)]
-15° 0° +10°
L 2'2" (0.67) 4'9" (1.45) 6'9" (2.06)
M 5'1" (1.54) 8'1" (2.46) 12' (3.65)
O 5'7" (1.69) 7'1" (2.15) 8'2" (2.50)
Q 8'3" (2.52) 10'6" (3.20) 11'8" (3.56)
S 12' (3.66) 14' (4.27) 15'7" (4.76)
The actual detection area may become smaller depending on the ambient light, the color / material of
NOTE
the object or the floor as well as the entry speed of the object.
The sensor may not be activated when the entering speed of the object or a person is slower than
2"(50mm) / sec. or faster than 4'11"(1500mm) / sec.
INSTALLATION
1 1. Affix the mounting template at the desired mounting position.
Refer to the chart in below.
2. Drill two mounting holes of ø1/8" (ø3.4mm).
3. To pass the cable through the header, drill a wiring hole of ø5/16" (ø8mm).
4. Remove the mounting template.
5. Remove the housing cover with screw driver as shown below.
Fix the sensor to the mounting surface with the two mounting screws.
Screw driver
Screw driver Cover fixing
H : Height from the floor to the bottom of the header
(The mounting height is "H + Y".)
Header
Y : Distance between the bottom of the header and the sensor
Sensor X : Distance between the door and the mounting surface
Maximum distance (Y)
Y
H
X 6'7" (2.00) 7'7" (2.30)
X
0
2" (0.05) 4" (0.10)
4" (0.10) 3" (0.08)
6" (0.15) 2" (0.06)
H
8" (0.20) 2" (0.05)
Door
10" (0.25) 2" (0.05)
12" (0.30) -
Floor
NOTE Make sure not to mount the bottom of the sensor lower than the bottom of the header.
CAUTION
Make sure to affix the mounting template as described in the above chart,
otherwise it can be dangerous since there may be no detection area around
Risk of getting caught
the threshold. Install the sensor as low as possible on the header.
2
Wire the cable to the door controller as shown below.
1.Grey
Power
1
1
supply
2.Grey
3.White
Activation
2
2
output
4.Yellow
5.White stripe
Safety
3
3
output 6.Yellow stripe
7.Red (+)
Test
4 4
input 8.Black (-)
Before starting the procedure, make sure that the power is turned OFF.
WARNING
When passing the cable through the hole, do not tear the shield
Danger of electric shock otherwise it may cause electric shock or breakdown of the sensor.
3
1.Plug the connector.
2.Supply power to the sensor. Adjust the detection area and set the dipswitches.
(See ADJUSTMENTS 5. Dipswitch settings, Table 1)
Make sure to connect the cable correctly to the door controller before turning the power ON.
NOTE
When turning the power ON or after adjusting the settings, do not enter the detection area for more
than 10 seconds in order to enable the presence detection.
Do not touch the dipswitches before turning the power ON, otherwise an error occurs.
Place the housing cover.
4
If wiring is to be exposed, break the knockout.
Do not use the sensor without the cover.
WARNING
When using the cable knockout, install the sensor indoors or use the rain cover
(Separately available) otherwise electric shock or breakdown of
Danger of electric shock
the sensor may occur.
A
C
B
D E F
G
H
N
O
P
Q
R
S
T
U
Presence area :1st-4th row
Motion area :5th row
Approach area :6th row
-15°
0°
10°
Insert
1
Lock release is in the identical position
on both side of the sensor.
2
Slide
[feet,inch(m)]
8'2" (2.50) 9'2" (2.80) 9'10" (3.00)
No limit
4" (0.10) 4" (0.11) 5" (0.12) 5" (0.12)
4" (0.09) 4" (0.10) 4" (0.11) 4" (0.11)
3" (0.08) 3" (0.08) 4" (0.09) 4" (0.10)
3" (0.07) 3" (0.08) 4" (0.09) 4" (0.09)
2" (0.06) 3" (0.07) 3" (0.08) 3" (0.08)
- -
- -
12 to 24VAC±10% / 12 to 30VDC±10%
Form A relay 50V 0.3A Max.
Form A relay 50V 0.3A Max.
Opto coupler / Voltage: 5 to 30VDC
Knockout Knockout
Mounting
surface
I
J
K L
M