Current GEPS24-180U Installation Manual

®
Tetra LED Systems Power Supply
GEPS24-180U (100-277 VAC input / 24 VDC output / 180 W)
Power Supply Features
• Supports all 24 VDC Tetra Channel Letters, Box signs and Contour
Product
• Dry and damp location rated
• Class 2 wiring per NEC Article 725 (SELV)
• IP66 rated: separate enclosure required

BEFORE YOU BEGIN

Read these instructions completely and carefully.
RISK OF ELECTRIC SHOCK
•
Disconnect power at fuse box or circuit breaker
before servicing or installing product.
•
Properly ground Tetra power supply.
®
RISK OF FIRE
•
Minimum 5 cm (2") spacing from heat producing
components required.
•
Minimum 10 cm (4") to side and 2.5 cm (1") spacing in
compartment surrounding component required.
•
Application considerations potentially requiring
additional spacing include high ambient temperature
seen by the power supply, poor contact with a heat
dissipating material, inadequate ventilation, or direct
exposure to sun.
•
Use only Tetra supply wire to make connection from
®
Tetra power supply to Tetra LED strip.
® ®
•
Use only approved wire for input/output connection.
Minimum size 18 AWG (0.82 mm
2
•
Follow all local codes.
RISK OF INJURY
• While performing installations described, gloves, safety glasses
or goggles should be worn.
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
• Limited to use in dry and damp locations.
• The suitability of rain enclosure shall be
determined if intended for wet location.
• The grounding and bonding of the LED Driver shall
be done in accordance with National Electric Code
(NEC) Article 600.
• Follow all National Electric Codes (NEC) and local
codes.
WARNING/AVERTISSEMENT
).
CAUTION/ATTENTION
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l'alimentation électrique à la boîte de fusibles ou au disjoncteur avant
l'entretien ou l'installation du produit.
• Assurez-vous de correctement mettre à terre l'alimentation électrique Tetra
RISQUES D'INCENDIE
• Un espacement minimum de 5 cm (2 ") entre les composantes émettrices de
chaleur est requis.
• Un espacement minimum de 10 cm (4 po) entre 2 alimentations de
puissance est requis ainsi qu'un espacement minimal de 2,5 cm (1 po) avec
toute enceinte.
• Certains environnements de l'application pourraient requérir un espacement
additionnel tels que la température ambiante autour de l'alimentation, un
mauvais contact avec une matière dissipatrice de chaleur, une ventilation
inadéquate ou une exposition directe au soleil
• N'utilisez que le fil d'approvisionnement Tetra
l'alimentation Tetra et la bande DEL Tetra
®
• N'utilisez que des fils approuvés pour les entrées/sorties de connexion. Taille
minimum 18 AWG (0.82 mm ).
2
• Respectez tous les codes locaux.
RISQUE DE BLESSURE
• Lors de l'exécution des installations décrites, des gants, des lunettes de
sécurité ou des lunettes de protection doivent être portées.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR
de la classe [A] est conforme à la NMB-005 du Canada.
Installation Guide
24
Volt
.
®
pour faire la connexion entre
®
.
®