Current DUAL LITE EVHC Series Manual

Automatic Tests
The unit will automatically initiate a self-test/self-diagnostic
cycle based on the following table:
Testing Period
Once a month
Once every
Installing the Unit: Final Assembly
6 months
1. Align housing slots over tabs on backplate.
2. Pivot housing and snap closed.
3. Aim the lamps. Do not press on the lenses.
Manual Tests
Using the unit test switch, users can initiate different
duration test cycles based on the following table:
Initiating Action
Press test switch once
Press test switch twice
Pressing the test switch any time after a 90 minute test
cycle has begun cancels the remainder of the 90 minute
test and returns the unit to normal operation.
SERVICE/MAINTENANCE
Service / Maintenance
Maintenance SERVICE /MAINTENANCE
This emergency lighting unit should be tested and maintained in accordance with National Electrical Code and NFPA 101 Life Safety
Code requirements. It is recommended that emergency light fixtures be tested for 30 seconds once a month and for 90 minutes once a
year.
Taking A Unit Out Of Service
If a unit is to be deliberately taken out of service for an extended period, the battery lead connector should be disconnected from the
charger circuit board and insulated so that the battery will go into storage in a fully charged condition.
Replacing The Battery
1. De-energize the AC power.
2. Disengage the housing cover from the backplate.
3. Disconnect the battery leads from the charger circuit board.
3. Disconnect the battery harness from the charger pcb.
4. Remove the battery from the clips inside the cover.
4. Disconnect the battery strap and remove battery pack.
5. Replace with a new battery (see unit model label for correct part number) and reconnect leads. 3. Disconnect the battery harness from the charger pcb.
5. Replace with a new battery (see unit model label or battery label for correct part number) and reconnect harness.
6. Reassemble cover to backplate. 4. Disconnect the battery strap and remove battery pack.
3. Disconnect the battery harness from the charger pcb.
4. Disconnect the battery strap and remove battery pack.
Replacing LED Lamps
The LED lamps inside the unit are not replaceable or field serviceable. Please see dual-lite.com for further assistance.
Troubleshooting
Emergency circuit does not work
• Batteries are shipped uncharged, please charge for 24 hours before testing.
• Batteries are shipped uncharged and disconnected. Connect battery leads and charge 24 hours before testing.
• Make sure the switch pcb and the button/light pipe is correctly seated and aligned.
• Make sure the charger board and test button/light pipe are properly seated and aligned.
• Check wiring connections. • Check wiring connections.
Batteries are shipped uncharged, please charge for 24 hours before testing.
Make sure the switch pcb and the button/light pipe is correctly seated and aligned.
Batteries are shipped uncharged, please charge for 24 hours before testing.
Make sure the switch pcb and the button/light pipe is correctly seated and aligned.
RECYCLING INFORMATION
All steel, aluminum, and thermoplastic parts are recyclable.
All steel, aluminum and thermoplastic parts are recyclable.
NOTICE: Emergency units contain rechargeable batteries which NOTICE: Emergency units contain rechargeable batteries which
must be recycled or disposed of properly.
must be recycled or disposed of properly.
currentlighting.com/dual-lite
Hubbell Lighting, Inc. Life safety Products • www.dual-lite.com
© 2022 HLI Solutions, Inc. All rights reserved. Information and
Copyright© Hubbell Lighting, Inc., All rights reserved • Specifications subject to change without notice.
specifications subject to change without notice. All values are design
or typical values when measured under laboratory conditions.
OPERATION
OPERATION
OPERATION
Duration of Test
1 minute
Alternating:
30 minutes or 60 minutes
Test Cycle
1 minute
90 minutes
SERVICE /MAINTENANCE
the Dual-Lite website for further assistance.
Dual-Lite
Dual-Lite
RECYCLING INFORMATION
93049114 1 10/13
93049114_evhc_inst_sht_R01
93049114 1 10/13
Printed in U.S.A.
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following.
When using electrical equipment, basic safety precautions
should always be followed, including the following:
ALL SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY
1. Do not use outdoors.
2. Do not let power supply cords touch hot surfaces.
3. Do not mount near gas or electric heaters.
1. Do not use outdoors.
4. Equipment should be mounted in locations and at heights where it will not readily be subject
2. Do not let power supply cord touch conductive surfaces.
to tampering by unauthorized personnel.
3. Do not mount equipment near gas or electric heaters.
5. The use of accessory equipment not authorized by the manufacturer may cause an
4. Equipment should be mounted in locations and at heights where it will not readily be subject
unsafe condition.
to tampering by unauthorized personnel.
6. Do not use this equipment for other than its intended purpose.
5. The use of accessory equipment not authorized by the manufacturer may cause an unsafe
7. Servicing of this equipment should be performed by qualified service personnel.
condition.
8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units once a month
6. Do not use this equipment for other than its intended purpose.
for a minimum of 30 seconds, and once a year for a minimum of 90 minutes.
7. Servicing of this equipment should be performed by qualified service personnel.
8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units
once a month for a minimum of 30 seconds, and once a year for a minimum of 90 minutes.
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
WARNING – This product contains chemicals known to the State of California to cause
WARNING – This product contains chemicals known to the state of California to cause cancer, birth
cancer, birth defects and/or other reproductive harm. Thoroughly wash hands after
93051469
93051470
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or
installing, handling, cleaning, or otherwise touching this product.
93051471
otherwise touching this product.
93051472
93052054
Emergency Lighting Equipment For Use in Damp Locations
93050644
93054690
93051469
93055110
Damp location listed units are suitable for installation in:
93051470
93050644
Emergency Lighting Equipment For Use In Damp Locations
93051471
93051469
1. Interior locations subject to moderate degrees of moisture, such as some basements,
93051472
93051470
93049114_F
93051841
93051471
some barns, some cold storage warehouses, and the like.
93052054
Damp location listed units are suitable for installation in:
93051472
93051841
2. Partially protected locations under canopies, marquees, roofed open porches and the like.
1. Interior locations subject to moderate degrees of moisture, such as some basements, some barns,
93052054
some cold storage warehouses, and the like.
Rev 06/02/22
2. Partially protected locations under canopies, marquees, roofed open porches and the like.
Twin-Head LED Emergency Lighting Unit
Standard, Remote, and Spectron
Installation, Operation, and Service Instructions
Twin-Head LED Emergency Lighting Unit
Standard, Remote, and Spectron® Equipped Models
Installation, Operation, and Service Instructions
READ AND FOLLOW
INSTRUCTIONS
INSTALLER:
INSTALLER:
EVHC Series
EVHC Series
EVHC Series
Equipped Models
®
93051469
93051469 93051469