Advertisement
Names of parts
Control unit
Control unit
Gears
LED
Button
Charging port
Fastening section
Outer cap
Sensor
Crank arm
ANT ID
Magnet
Left crank
Connection
Connector
terminal
Electric wire
Operation
You cannot use the battery immediately after shipment.
Be sure to charge it before use.
Charging the battery
This product can be charged by using an AC adapter with a USB port or by
connecting it to the USB connector of a PC.
Power may no longer be supplied to the battery if the PC enters a
hibernation or sleep state while charging.
1. Pull at the indent in the control unit to open the cover.
Push upward
Indent
2. Connect the charging cable as shown in the illustration. (Match the
shapes of the charging cable and charging port when connecting.)
3. Once charging begins, the LED lights up blue.
(Do not move the crank or cable during charging. There is a risk of the cable
disconnecting. Reconnect the cable if it disconnects.)
LED
(lights up blue)
4. Once charging is complete, the LED turns off.
After charging, make sure to close the cover.
How to check battery level
1. Press the button on the control unit.
2. The LED is green or red.
If the LED is red, fl ashing, or does not turn ON, the battery level is low.
Charge the battery.
LED
Battery level
Green
100% - 16%
Red
15% - 3%
LED
Red
(lights up
2% - 1%
green or red)
(fl ashing)
Off
0%
Note:
When the LED is lit up red, you will not be able to connect to E-TUBE
PROJECT.
If you continue usage in this state and the LED fl ashes red, you will be
unable to set zero offset.
Activating the product
Press the button on the control unit or rotate the crank 2 or more times.
Confi rming the product has activated
• Activation by pressing the button
Remaining battery charge displays.
• Activation by rotating the crank (after connecting cycle computer)
Cadence and power display on the cycle computer when the product is
active.
If this product does not detect motion for 5 minutes after activation,
wireless transmission will terminate in order to save battery power.
To re-enable the wireless connection, either press the button on the
control unit or rotate the crank 2 or more times.
Connection procedure
Cycle computer connection
To make a connection, the cycle computer needs to be in connection mode.
For information on how to put the cycle computer into connection mode,
refer to the manual for the cycle computer.
1. Activate the product by pressing the button on the control unit or
rotating the crank 2 or more times.
2. Select the unit name displayed on the cycle computer screen.
For an ANT
connection, you can also connect by entering the fi ve
+ TM
digit ANT ID found on the reverse side of the right crank.
ANT ID
3. This completes the connection process.
Check on the cycle computer to see if connection was successful.
If a connection cannot be made in the way described above, refer to the
manual for your cycle computer.
E-TUBE PROJECT connection
Before setting up a connection, turn on Bluetooth LE on the smartphone/
tablet.
1. Open E-TUBE PROJECT and set it to listen for Bluetooth LE signals.
2. Press the button on the control unit.
3. Select the unit name displayed on screen.
* To disconnect, cancel the Bluetooth LE connection from the smartphone/
tablet. (The cycle computer will exit connection mode and return to
regular operation mode.)
To restore the Bluetooth LE Name and Passkey to their default values,
hold down the button on the control unit for at least 3 seconds during
battery charging. The LED will fl ash blue.
(Bluetooth LE Name: FCR9100P Passkey: 000000)
Performing zero offset calibration
• Zero offset calibration can be performed using the control unit or the cycle
computer.
When calibrating using the cycle computer, refer to the instruction manual
for the cycle computer.
• It is recommended to perform zero offset calibration before riding the
bicycle.
1. Place the bicycle on level ground.
(At this time, do not place your feet on the pedals or apply load to the
crank. It may not be possible to perform calibration correctly.)
2. Position the crank arm so that it is perpendicular to the ground as in the
illustration.
(Zero offset calibration is unaffected by whether the chain is positioned
on the largest chainring or smallest chainring.)
3. Press the button on the control unit until the LED lights up blue.
LED
(lights up blue)
Button
4. When the LED lights up blue, release the button.
The LED will begin blinking and zero offset calibration will complete.
LED
(blinks blue)
When connected to a cycle computer via ANT
or connected to E-TUBE
+ TM
PROJECT, "5050" will be displayed on your cycle computer, smartphone,
or tablet once zero offset confi guration is complete.
If some other number is displayed even if you perform zero offset
confi guration again, contact the place of purchase or a bicycle dealer.
Specifi cations
Operating
Continuous
300 or more hours
temperature
-10°C – 50°C
operation
(for given
range
time
temperature of 25°C)
Battery type
Lithium ion
Normal
2.5 hours
charging time
Wireless
ANT
/Bluetooth
+
TM
Charging
specifi cation
0°C – 45°C
temperature
Frequency band
2,402 – 2,480 MHz
Maximum radio-frequency power
+4 dBm
Firmware version
4.0.3 –
Troubleshooting
If you experience any trouble using this product, please refer to the
following.
If none of the following are applicable, or the suggested solution does not
resolve the issue, consult with the place of purchase or a bicycle dealer.
If the power value has changed, it is possible to correct it. For details, consult
the place of purchase.
The cycle computer may not be connected.
Follow the steps in "Connection procedure" to make a
connection.
The battery may be out of charge.
Power does not
Check remaining battery charge and charge the battery
display
if the charge is low.
The left crank connector may be detached.
Remove the outer cap and check that the connector is
connected.
Zero offset calibration may not be correct.
Power value is
Perform zero offset calibration referring to the section
abnormal
"Performing zero offset calibration".
The magnet may not be attached or may be positioned
Cadence does not
incorrectly.
display
If it is not attached or it is positioned incorrectly,
consult with the place of purchase or a bicycle dealer.
Cadence value is
Another cadence sensor may be attached.
abnormal
If this is the case, either remove or disable it.
There may have been an issue during zero offset
LED blinks red
calibration.
during zero offset
Confi rm that the connector is connected and perform
calibration
zero offset calibration again referring to the section
"Performing zero offset calibration".
A USB hub may be connected.
Do not use a USB hub.
Charging is not
possible
The charging cable may be damaged.
If charging is not possible even after trying a different
PC or USB adapter, replace the charging cable.
The cycle computer in use may not be supported.
Confi rm with the instruction manual for the cycle
computer.
Interference may be affecting the wireless signals.
Wireless signals may be susceptible to interference in
the following locations and conditions, preventing
Connection cannot
successful connection.
be made with cycle
* Near televisions, PCs, radios, motors/engines etc., or
computer
inside cars and trains.
* Near railroad crossings, railway tracks, television
transmitting stations or radar bases, etc.
* When used alongside other wireless/cordless devices
or certain types of lighting.
Change location and reattempt connection.
About hardware reset
If an issue cannot be resolved even after referring to the troubleshooting
section, perform a hardware reset.
1. Hold down the button on the control unit for 15 seconds.
2. The hardware reset completes when the button is released.
3. When the hardware reset is complete, the LED will light up indicating
remaining battery charge.
After the hardware reset is complete, check operation again and if the
issue has not been resolved, consult with the place of purchase or a
bicycle dealer.
®
LE
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
High Tech Campus 92, 5656 AG Eindhoven, The Netherlands Phone: +31-402-612222
Please note: specifi cations are subject to change for improvement without notice. (English)
© Feb. 2018 by Shimano Inc. ITP
Advertisement
