Related Manuals for Magnum MSC 2101
Summary of Contents for Magnum MSC 2101
- Page 1 SUBMERSIBLE CONTRACTOR PUMP MSC 2101 • MSC 2202 • MSC 2302 MSC 3202 • MSC 3302 OPERATING/PARTS MANUAL...
-
Page 2: Introduction
Keep a copy of this manual with the unit at all times. Additional copies are available from Magnum Products LLC, or can be found at www.m-p-llc.com. The information contained in this manual was based on machines in production at the time of publication. -
Page 3: Table Of Contents
COMPONENT LOCATIONS - MSC 2101, MSC 2202 & MSC 3202 ............. 8 COMPONENT LOCATIONS - MSC 2302 & MSC 3302 ................ 9 UNIT ASSEMBLY AND PARTS - MSC 2101, MSC 2202 & MSC 3202 ........10 - 11 UNIT ASSEMBLY AND PARTS - MSC 2302 & MSC 3302 ............12 - 13 WIRING DIAGRAM - MSC 2101 ...................... -
Page 4: Safety Notes
SAFETY NOTES This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. This manual contains DANGERS, WARNINGS, CAUTIONS, NOTICES and NOTES which must be followed to prevent the possibility of improper service, damage to the equipment, personal injury or death. -
Page 5: Unit Serial Number Location
Read this manual carefully before attempting to use this pump. The potential for property damage, personal injury or death exists if this equipment is misused or installed incorrectly. MAGNUM MODEL MSC 2101 MSC 2202 MSC 2302 Motor Type ..........1 Ø, 60 hz ......1 Ø, 60 hz......1 Ø, 60 hz Amperage Range (Min. -
Page 6: Specifications
SPECIFICATIONS Read this manual carefully before attempting to use this pump. The potential for property damage, personal injury or death exists if this equipment is misused or installed incorrectly. MAGNUM MODEL MSC 3202 MSC 3302 Motor Type ..........1 Ø, 60 hz ......1 Ø, 60 hz Amperage Range (Min. -
Page 7: Operating The Pump
OPERATING THE PUMP 1. Connect the discharge hose with the proper fittings. 2. Place the pump in the water. Lower by attaching a strong rope to the handle. The pump should be placed on a flat, hard surface in at least 2 inches of water. WARNING Never lower or move the pump with the electrical cord. -
Page 8: Component Locations - Msc 2101, Msc 2202 & Msc 3202
COMPONENT LOCATIONS - MSC 2101, MSC 2202 & MSC 3202 CORD DISCHARGE HANDLE HOUSING IMPELLER (UNDER INLET) INLET... -
Page 9: Component Locations - Msc 2302 & Msc 3302
COMPONENT LOCATIONS - MSC 2302 & MSC 3302 DISCHARGE HANDLE HOUSING IMPELLER (UNDER INLET) INLET... -
Page 10: Unit Assembly And Parts - Msc 2101, Msc 2202 & Msc 3202
UNIT ASSEMBLY AND PARTS - MSC 2101, MSC 2202 & MSC 3202... - Page 11 ITEM NO. PART NO. DESCRIPTION NOTES 41618 Handle 41612 Power cord For MSC 2202 & 3202 41611 Power cord For MSC 2101 41770 Rubber gasket For MSC 2202 & 3202 41769 Rubber gasket For MSC 2101 41720 Base-capacitor 41636 Upper bearing For MSC 2202 &...
-
Page 12: Unit Assembly And Parts - Msc 2302 & Msc 3302
UNIT ASSEMBLY AND PARTS - MSC 2302 & MSC 3302... - Page 13 ITEM NO. PART NO. DESCRIPTION NOTES 41620 Handle 41613 Power cord 41770 Rubber gasket 41720 Base-capacitor 41637 Upper bearing 41626 Capacitor - run 41667 Capacitor - start 41732 Impeller key 41644 Lower bearing 41652 Mechanical seal 41661 Seal plate 41694 Impeller For MSC 3302 41695...
-
Page 14: Wiring Diagram - Msc 2101
WIRING DIAGRAM - MSC 2101... -
Page 15: Wiring Diagram - Msc 2202, Msc 2302, Msc 3202 & Msc 3302
WIRING DIAGRAM - MSC 2202, MSC 2302, MSC 3202 & MSC 3302... - Page 16 REV: A PART NO: 41866 01.28.09...