Chattanooga Group Optiflex S User Manual
  1. Manuals
  2. Brands
  3. Chattanooga Group Manuals
  4. Medical Equipment
  5. Optiflex S
  6. User manual

Chattanooga Group Optiflex S User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Problem
Solving
Through
Innovation!

User Manual

Advertisement

Table of Contents
loading

Related Manuals for Chattanooga Group Optiflex S

Summary of Contents for Chattanooga Group Optiflex S

  • Page 1: User Manual

    Problem Solving Through Innovation! User Manual...

  • Page 2: Table Of Contents

    Replacement Parts List ..........26 OPTIFLEX S USER MANUAL...

  • Page 3: Precautionary Instructions

    • Rapid increases in ROM can cause complications. • Materials may become flammable or combustible if exposed to a • OptiFlex S is not to be used in the presence of flammable anesthetic source of ignition. mixture with air or with oxygen or nitrous oxide.

  • Page 4: Safety Instructions

    Always review settings prior to patient’s use. • If necessary, large ranges of motion can be set with the OptiFlex S. continuously supervised by specialist staff.

  • Page 5: Foreword

    It contains general instructions on operation, precautionary practices, maintenance and parts information. In order to maximize use, efficiency and the life of your OptiFlex S, please read this manual thoroughly and become familiar with the controls as well as the accessories before operating the unit.

  • Page 6: Product Description

    OptiFlex S lessens the adverse effects of immobilization and trauma on the joint (see Indications section, page 7). OptiFlex S is a prescription device used under the supervision or by the order of a physician or other licensed healthcare provider.

  • Page 7: Indications

    • Decreasing post-operative pain and swelling • Possible increase in fluid dynamics • Decreasing hospital stays Clinical Indications OptiFlex S may benefit patients who have undergone: • Shoulder arthroplasty • Revision total joint arthroplasty • Manipulation of elbow or shoulder •...

  • Page 8: Adjusting The Optiflexs

    NOTE: The plugs for the mobility element can only be connected in one direction (see figure D). Also, make sure that the mobility 4. Tighten the wing screw (13) securely. element’s connector is always locked on using the safety hinge. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...
  • Page 9 4. Adjust the angle of the backrest in all other ante/retroversion settings in order to optimize the correspondence between Motor A (15) and the rotating axis of the patient’s shoulder joint. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...

  • Page 10: Pendant Nomenclature

    PENDANT NOMENCLATURE LED DISPLAY STOP AB/ADDUCTION START ROTATION SPECIAL PAUSE FUNCTIONS MOTOR ON/OFF “+” SPEED “-” TIMER OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...

  • Page 11: Programming The Optiflexs

    + or - button. 4. Continue programming (see Information on the Treatment Values Programming [page 12] and Special Functions [page 14] subheadings in this chapter) until you have entered all the values required. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...
  • Page 12 Set Motor B in 90° external rotation and switch off.) Internal Rotation 90° External Rotation 90° CAUTION! If the shoulder immobilization option is used, abduction may not be programmed above 80°. Manual Anteversion (horizontal adduction) 120° Retroversion (horizontal abduction) 0° OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...
  • Page 13 2. The device will stop at the midpoint of the treatment range automatically when the therapy time is complete. 3. In Continuous mode, the treatment is terminated by pressing the STOP button. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...
  • Page 14 4. Follow the directions on the LED Display. 5. Terminate with the STOP button. New Patient When this special function is activated, the OptiFlex ® S is reset to the factory setting. All previously programmed values are deleted. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...
  • Page 15 2. Select the “Factory Settings” function with the + or - button. 3. Activate the function with the SET button. 4. Press the START button. 5. The device enters the factory setting and stops automatically. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...
  • Page 16 In asynchronous use, the two motors operate independently in the relevant range of motion. This mode requires particular care and attention on the part of the operator to ensure that the OptiFlex S is used without any risks to the patient. OPTIFLEX S USER MANUAL...
  • Page 17 1. Select “Therapy Duration” function using the + or - button. The length of therapy will be displayed. 2. To clear “Therapy Duration” function, hold down the SET button for five seconds. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...
  • Page 18 0 - 100%. To set this value, press SET again. Service Menu This is intended for certified service personnel only. See service manual. Save Data To save the programmed special functions, press the STOP button. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...

  • Page 19: Converting The Optiflexs

    CONVERTING THE OPTIFLEX ® The OptiFlex S is easily converted. See the Parts Description on page 22 to help locate any parts. Programming Steps 1. Set ante/retroversion to 90° (1). 2. Set Motor A to 90° and Motor B to 0°.

  • Page 20: Transporting The Optiflexs

    Reinsert the safety bolts. CAUTION! Before starting the OptiFlex S, make sure that it is at room temperature. If the unit is exposed to temperatures below freezing during transport, the device MUST BE...

  • Page 21: Technical Specifications

    Lower Arm Length 11” - 18” (29 - 46 cm) Seat Height 19” (48cm) Weight 55 lbs. (25 kg) Class 2a IEC 60601-1 1990 + A1: 1993 + A2: 1995 CSA 601.1-M90 Standard 2601-1 OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...

  • Page 22: Parts Description

    24. Outer tube for adjusting the lower arm length 25. Eccentric lever for adjusting the lower arm length 26. Inner tube for adjusting the lower arm length 27. Wing Screw for swivel mechanism 28 Hand Support OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...
  • Page 23 I I n n s s e e t t o o f f B B a a c c k k OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...

  • Page 24: Warranty

    Any modifications or repairs performed by unauthorized centers or groups will void this warranty. To participate in warranty coverage, this Product's warranty registration card (included with Product) must be filled out and returned to Chattanooga Group by the original owner within ten (10) business days of purchase.
  • Page 25 The Company does not authorize any person or representative to create for it any other obligation or liability in connection with the sale of the Product. Any representation or agreement not contained in the warranty shall be void and of no effect. OPTIFLEX S USER MANUAL OPTIFLEX S USER MANUAL...

  • Page 26: Replacement Parts List

    Seat 20679 Backrest 20680 Wheel Assembly 20681 Tube Cap 20686 Rubber Glide 20687 OptiCard ™ Holder OptiFlex ® S Accessories 20660 – Patient Softgoods Kit 20661 – OptiCard Chip cards (5 Pack) 20664 – OptiCard Pen OPTIFLEX S USER MANUAL...
  • Page 27 More Trusted Products from Chattanooga Group Achiever ™ OptiFlex ® and OptiFlex ® Supports Continuous Passive Motion Opti-Ice ™ Adapta ® Treatment Tables Cold Therapy System A.E.R. ® Boot and Compression Para-Care ® Auto Edema Reduction Boot Paraffin Wax Unit Pillow Perfect ™...

This manual is also suitable for:

Optiflex s

Table of Contents