Leviton 48A00-1 Installation Instructions And Operators Manual

WARNINGS AND CAUTIONS
• Read and understand all instructions. Follow all warnings and instructions marked on the product.
• Do not use this product near water - e.g., near a tub, wash basin, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
• Never push objects of any kind into this product through openings, as they may touch dangerous voltages.
• Never install communications wiring or components during a lightning storm.
• Never install communications components in wet locations unless the components are designed specifically for use in wet locations.
• Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface.
• Use caution when installing or modifying communications wiring or components.
• SAVE THESE INSTRUCTIONS.
DESCRIPTION
The 48A00-1 4-Button Keyfob Remote is used to send up to 8 different wireless signals to the Leviton 45A00-1 Wireless Receiver to activate
automation programs in the Leviton controller. Each button, or combination of buttons, can activate lighting, arm and disarm the security
system, operate a garage door, set off a panic alarm, and many other functions.
OPERATION
When you press a button on the Keyfob, a transmission will be sent after a 3/10 second delay. If you wish, you can program the buttons to
have a variety of delays to help avoid accidental transmission. When the signal is transmitted, the LED will light for conformation that the
transmission was sent.
NOTE: Button 4 is factory programmed to have a 2 second delay. You must press and hold Button 4 for 2 seconds before it will transmit.
You can also virtually eliminate false panic alarms by configuring the panic alarm to only activate when two buttons are pressed
simultaneously. This configuration is perfect for Police or Duress panic alarms. It helps reduce false alarms by insuring a signal is sent only
if two buttons are pressed simultaneously.
ENROLLING EACH OF THE 4 BUTTONS ON THE 48A00-1
To enroll the 48A00-1, put the 45A00-1 Wireless Receiver in to Setup mode, advance to an unused address location, and then press one of
the buttons on the Keyfob. Advance to another unused address location, and then press the next button for one additional zone. Advance to
another unused address location and press the next button for two additional zones. Advance to another unused address location and press
the final button for three additional zones. Refer to the Installation Instructions for the 45A00-1 for additional information.
USING THE 4 ADDITIONAL ZONE INPUTS
A combination of button presses can be used to activate 4 additional zones. To activate these zones, the combination of buttons must be
pressed simultaneously.
To enroll the 4 additional zones on the 48A00-1, follow the procedure as stated above, but use the combination of buttons shown below.
Refer to the Installation Instructions for the 45A00-1 for additional information.
PROGRAMMING FEATURES
The 48A00-1 can be programmed to change some operating parameters to provide maximum flexibility.
To Enter Programming:
1) Press and HOLD all four buttons simultaneously until the LED begins to flash (approximately 2 seconds).
2) Press Button 1 (upper left) for a 2 second delay
programmed delay on all other buttons.
Once you have pressed Button 1 or Button 2, the LED will flash faster.
3) With the LED flashing, press Button 1 (upper left) for instant transmission on all buttons
second delay (default) on all buttons
1
a 2 second delay on all buttons
1
KEYFOB REMOTE
Cat. No. 48A00-1
INSTALLATION
on Button 4 (default) or press Button 2 (upper right) to set the delay on Button 4 to the
1
, press Button 3 (lower left) for a 1 second delay
2
.
2
, press Button 2 (upper right) for a 3/10 of a
2
on all buttons , or press Button 4 (lower right) for
1 2
DI-021-SY480-05A
AR2253
(48I00-1)
ENGLISH