FiberHome HG6543C Product Manual
  1. Manuals
  2. Brands
  3. FiberHome Manuals
  4. Network Router
  5. HG6543C
  6. Product manual

FiberHome HG6543C Product Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

HG6543C
Product Manual
Version: A
FiberHome Telecommunication Technologies Co., Ltd.
July 2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HG6543C and is the answer not in the manual?

Questions and answers

Related Manuals for FiberHome HG6543C

Summary of Contents for FiberHome HG6543C

  • Page 1 HG6543C Product Manual Version: A FiberHome Telecommunication Technologies Co., Ltd. July 2019...
  • Page 3 Please contact your local sales representative, service representative or distributor for any help needed at the contact information shown below. Fiberhome Telecommunication Technologies Co., Ltd. Address: No. 67, Guanggu Chuangye Jie, Wuhan, Hubei, China Zip code: 430073...
  • Page 5 Legal Notice are trademarks of FiberHome Telecommunication Technologies Co., Ltd. (Hereinafter referred to as FiberHome) All brand names and product names used in this document are used for identification purposes only and are trademarks or registered trademarks of their respective holders.

  • Page 7: Safety Precautions

    Safety Precautions For your correct and safe operations on the equipment, please carefully read and strictly observe the following safety instructions: High optical power can cause bodily harm, especially to eyes. Never look directly into the end of the optical transmitter fiber jumper or the end of its active connector.

  • Page 9: Table Of Contents

    2.3.1 GPON Interface ..............4 2.3.2 LAN Interface..............4 2.3.3 POTS Interface..............5 2.3.4 Wi-Fi Interface ..............5 2.3.5 USB Interface ..............5 Introduction to the HG6543C.............6 2.4.1 Appearance ................6 2.4.2 Product Characteristics.............10 2.4.3 Functions and Features ............12 2.4.4 Technical Specifications............16 Web Configuration Guide ................17 Local Login to the Web Configuration GUI ........18...
  • Page 10 3.3.4 DHCP Server..............39 3.3.5 Authentication Settings .............41 3.3.6 IPv6..................42 3.3.7 Voice Configuration............43 Security ..................51 3.4.1 Firewall................51 3.4.2 Remote Control ..............61 3.4.3 Route QoS................62 3.4.4 ACL Configuration ............64 3.4.5 Dynamic DoS ..............66 3.4.6 HTTPS ................66 Application..................67 3.5.1 VPN .................67 3.5.2 DDNS................68 3.5.3 Port Forwarding ..............69 3.5.4...
  • Page 11 4.10 Test of Voice Service Failed ............85 Standards and Protocols................86 Appendix A Abbreviations ................88...

  • Page 13: Documentation Guide

    Documentation Guide Document Orientation HG6543C Product Manual introduces the positioning, features, functions and technical specifications of the HG6543C as well as Web configurations and handling of common problems, so that readers can have an overall idea about the HG6543C. Intended Readers...

  • Page 14: Product Introduction

    Product Introduction Product Positioning Product Specification Interface Specifications Introduction to the HG6543C Version: A...

  • Page 15: Product Positioning

    2 Product Introduction Product Positioning The HG6543C is an FTTH-type GPON optical network terminals. It provides users with communication and entertainment services in the form of data, voice, video and so on, to meet the integrated access demand of families and small-scaled enterprises.

  • Page 16: Interface Specifications

    HG6543C Product Manual Table 2-2 lists the service types supported by the HG6543C. Table 2-2 Service Types Supported by the HG6543C ONT Type Internet Service Multicast Service Voice Service Wi-Fi Service HG6543C " " indicates "supported"; "×" indicates "not supported".

  • Page 17: Pots Interface

    2 Product Introduction Specification Item Maximum transmission 100 m distance Supports full-duplex / half-duplex and auto negotiation to rates Working mode 10/100/1000 Mbit/s. Specifications of the CAT-5 unshielded twisted pair cable used 2.3.3 2.3.3 POTS Interface Specification Item Interface type RJ-11 Transmission rate 64 Kbit/s...

  • Page 18: Introduction To The Hg6543C

    HG6543C Product Manual Introduction to the HG6543C 2.4.1 2.4.1 Appearance This section describes the appearance of the HG6543C, including the overall look, interfaces, buttons, and indicator LEDs. Note: The pictures here are only for reference. Appearance The overall look of the HG6543C is shown in Figure 2-1.
  • Page 19 2 Product Introduction Interfaces and Buttons Interfaces and buttons of the HG6543C are located on the rear, side and bottom panels of the equipment. Figure 2-2, Figure 2-3 and Figure 2-4 show the rear panel, side panel and bottom panel respectively.
  • Page 20 HG6543C Product Manual Figure 2-3 Side Panel of the HG6543C Figure 2-4 Bottom Panel of the HG6543C Table 2-3 describes the interfaces and buttons on the HG6543C. Version: A...
  • Page 21 WPS function button Connects with the optical fiber for uplink access. Fiber interface Indicator LEDs Indicator LEDs of the HG6543C are located on the front panel of the equipment. Table 2-4 describes the indicator LEDs. Table 2-4 Indicator LEDs on the HG6543C...

  • Page 22: Product Characteristics

    The port is not registered in the softswitch system. 2.4.2 2.4.2 Product Characteristics The HG6543C can be used together with the OLT equipment to make up a GPON system and provide users with access to multiple services. The HG6543C has the following characteristics: Version: A...
  • Page 23 2 Product Introduction 1. GPON Access Capability Conforms to ITU-T G.984 series of standards, with good interoperability. Provides large-capacity GPON transmission bandwidth: supports the downlink rate up to 2.5 Gbit/s and the uplink rate up to 1.25 Gbit/s. Supports the dynamic bandwidth allocation (DBA) algorithm. Supports long-haul transmission.

  • Page 24: Functions And Features

    HG6543C Product Manual 5. Gateway Functions Serves as home gateway and provides abundant and reliable gateway functions. Functions as the DHCP Server to cater for application demands in different scenarios. Supports configuring protection against DoS attacks, filtering of MAC addresses, IP addresses and URL addresses, firewall and ACL rules to guarantee safe operation of the equipment.
  • Page 25 2 Product Introduction Specification Item Supports bearing the downlink broadcast messages and unknown multicast messages via the broadcast GEM ports. Supports mapping from GEM ports to T-CONTs. GEM port Supports multiple flow mapping modes: Supports the GEM port loopback. Supports the T-CONTs of Type1 to Type 5. A T-CONT supports no less than 64 GEM ports.
  • Page 26 HG6543C Product Manual Specification Item Supports enabling / disabling the MAC address learning function globally. Supports remote configuration of the MAC address aging time. The value ranges between 0s and 300s. The default value is 80s. Supports the IGMP Snooping protocol.
  • Page 27 2 Product Introduction Specification Item Supports DDNS, NAT, port forwarding and DMZ. Supports ARP, UPnP, ALG, Portal and QoS. Supports the protocols H.248 and SIP. Supports the speech encoding modes such as G.711, G.729, G.723.1 and G.722. Provides a phone number for each connected telephone set. Supports simultaneous call and conversation of two POTS Voice subscribers.

  • Page 28: Technical Specifications

    HG6543C Product Manual Specification Item Supports configuring the HTTPS safe channel. Supports configuring ACL rules for the ONT. Supports remote control. Supports local service configuration, query and software upgrade based on the Web page. Management and Supports management of OMCI configurations and queries.

  • Page 29: Web Configuration Guide

    Web Configuration Guide This chapter introduces the Web GUI for the HG6543C administrator, including the parameter meanings and operation methods. Note: Configure the ONT on the OLT via the access network management system. For details, please refer to the relevant OLT configuration guide.

  • Page 30: Local Login To The Web Configuration Gui

    HG6543C Product Manual Local Login to the Web Configuration GUI This section introduces the local login to the ONT's Web GUI and the layout of the configuration GUI. Prerequisites The ONT has been connected to the computer correctly. The user computer is started normally.
  • Page 31 3 Web Configuration Guide Table 3-1 Planning Data for Local Login to the Web GUI Description Item Factory default value: Administrator Username: admin Password: %0|F?H@f!berhO3e Common user Username: user Username and password Password: user1234 Note: Some operators require customized username and password, so that the default username and password may be different from the ones mentioned above.
  • Page 32 HG6543C Product Manual In the Windows taskbar, select Start Control Panel and click Network and Sharing Center. Click Local Area Connection to bring up the Local Area Connection Status dialog box, and click Properties. In the Local Area Connection Properties dialog box that appears, double-click Internet Protocol 4 (TCP/IPv4).
  • Page 33 3 Web Configuration Guide Click OK to save the configurations. The operations in the Windows XP operating system are as follows: In the Windows taskbar, select Start Control Panel. Double-click Network Connection to access the network connection window. Right-click Local Connection and select Properties from the shortcut menu to bring up the Local Connection Properties dialog box.
  • Page 34 HG6543C Product Manual Double-click Internet Protocol (TCP/IP). In the Internet Protocol (TCP/IP) Properties dialog box that appears, set the IP address and subnet mask of the computer. For details of the parameters, see Table 3-1. Version: A...
  • Page 35 3 Web Configuration Guide Click OK to save the configurations. Enter http://192.168.1.1 (default management IP address of the ONT) in the browser address bar of the computer, and press the Enter key to bring up the user login dialog box. Enter the administrator username and password in the login dialog box.

  • Page 36: Status

    HG6543C Product Manual Note: The screenshots provided here are for reference only, and the actual Web GUIs for the equipment shall prevail. The configuration GUIs for the administrator are different from those for common users: The administrator can view and configure all the node items in the Web GUI.

  • Page 37: Wireless Network Status

    3 Web Configuration Guide Figure 3-2 Device Information 3.2.2 3.2.2 Wireless Network Status View the information about the wireless network, such as network mode, frequency channel, SSID, count of wireless packets, and list of Wi-Fi clients. 3.2.2.1 3.2.2.1 Wireless Network Status Select Status in the navigation bar, and then select Wireless Status Wireless Status in the left link bar to view the information of the wireless network, such as network mode, band, SSID and wireless packet statistics, as shown in Figure 3-3.

  • Page 38: Wan Side Status

    HG6543C Product Manual Figure 3-3 Wireless Network Status 3.2.2.2 3.2.2.2 Wi-Fi User List Select Status in the navigation bar, and then select Wireless Status WIFI Clients List in the left link bar to view the list of client ends connected to the ONT wireless network, as shown in Figure 3-4.

  • Page 39: Lan Side Status

    3 Web Configuration Guide Figure 3-5 WAN Side Status 3.2.4 3.2.4 LAN Side Status Check the state information about the LAN interface and the DHCP client end. 3.2.4.1 3.2.4.1 LAN Side Status Select Status in the navigation bar and select Lan Status Lan Status in the left link bar to view the information such as the IP address and subnet mask of the LAN side, as shown in Figure 3-6.

  • Page 40: Optical Power Status

    HG6543C Product Manual Figure 3-7 DHCP User List 3.2.5 3.2.5 Optical Power Status Select Status in the navigation bar and select Optical Info Optical Info in the left link bar to view the optical module information such as the Tx optical power, Rx optical power and working temperature, as shown in Figure 3-8.

  • Page 41: Network

    3 Web Configuration Guide Network This section introduces how to make the WLAN, LAN, broadband, DHCP server, authentication, IPv6 and voice configurations in the Web GUI. 3.3.1 3.3.1 WLAN Settings This section introduces how to configure Wi-Fi control and WPS as well as basic and advanced parameters of the wireless network on the Web page.
  • Page 42 HG6543C Product Manual Table 3-2 Basic Parameters of the 2.4G Wireless Network Description Item Enables or disables the WLAN service. RADIO ON: the wireless network is Radio ON/OFF enabled; RADIO OFF: the wireless network is disabled. The mode supported by the wireless network. The options include 802.11b, 802.11g, 802.11b/g, 802.11n and 802.11b/g/n.
  • Page 43 3 Web Configuration Guide Configure the parameters of the 2.4G wireless network, such as the SSID, password, security mode and algorithm. For details of the parameters, see Table 3-3. Click Apply to save and apply the configuration. Table 3-3 Advanced Setting Parameters of Wireless Network Description Item Select the SSID.
  • Page 44 HG6543C Product Manual Table 3-3 Advanced Setting Parameters of Wireless Network (Continued) Description Item Select Key1 to Key4; that is, select one of the four This item should be Default Key configured network keys. configured when the authentication mode Enter the key value and select the key value type. At is OPEN and the least enter the item selected in Default Key.
  • Page 45 WPS Configuration WPS can automatically set the wireless network name (SSID) and wireless encryption key for the HG6543C and client end supporting the Wi-Fi service. You need only to press down the WPS button or enter the PIN to achieve safe connection.

  • Page 46: Lan Settings

    HG6543C Product Manual Figure 3-13 WPS Configuration Select whether to enable the WPS function. The options include Enable and Disable. Select the WPS connection mode as required. Select Please input PIN code., and enter the PIN code of the client end in the PIN text box.
  • Page 47 3 Web Configuration Guide Figure 3-14 LAN Settings Configure the management IP address and subnet mask at the LAN side. For details of the parameters, see Table 3-5. Click Apply to save and apply the configuration. Table 3-5 Parameters of LAN Settings Item Description The management IP address at the LAN side of the ONT.

  • Page 48: Broadband Settings

    HG6543C Product Manual Table 3-5 Parameters of LAN Settings (Continued) Item Description The source of the DNS distributed to the PC. The options include WAN connection, ONT proxy and static configuration. The default DNS Source setting is WAN connection. The source of the prefix information distributed to the PC. The options Prefix Mode include WAN connection and static configuration.
  • Page 49 3 Web Configuration Guide Figure 3-15 Internet Settings Configure parameters relevant to the Internet at the WAN side. For details of the parameters, see Table 3-6. Click Apply to save and apply the configuration. Table 3-6 Parameters for Internet Settings Description Item Select the service type at the WAN port.
  • Page 50 HG6543C Product Manual Table 3-6 Parameters for Internet Settings (Continued) Description Item Priority Sets the priority of the VLAN. The value range is 0 to 7. Enables or disables the NAT function. Users need to configure this item DNS Relay Enables or disables the DNS relay function.

  • Page 51: Dhcp Server

    3 Web Configuration Guide Table 3-6 Parameters for Internet Settings (Continued) Description Item Enter the username provided by the ISP. User Name This item should be set if Enter the password provided by the ISP. Password the WAN IP Mode is set to Sets the PPPoE connection mode.
  • Page 52 HG6543C Product Manual Select Network in the navigation bar, and then select DHCP Server DHCP Service from the left link bar to open the DHCP server configuration page, as shown in Figure 3-16. Figure 3-16 DHCP Service Configure the DHCP server parameters as required. For details of the parameters, see Table 3-7.

  • Page 53: Authentication Settings

    3 Web Configuration Guide Table 3-7 Parameters for the DHCP Server (Continued) Description Item DHCP Subnet The mask of the active DHCP server. Mask DHCP Primary The IP address of the active DNS server. DHCP Secondary The IP address of the standby DNS server. DHCP Default The default gateway of the active DHCP server.

  • Page 54: Ipv6

    HG6543C Product Manual Figure 3-17 OLT Authentication Configure the parameters as required. For details of the parameters, see Table 3-8. Click Apply to save the configuration information. The configuration will take effect after the ONT is rebooted. Table 3-8 Parameters for OLT Authentication...

  • Page 55: Voice Configuration

    3 Web Configuration Guide Figure 3-18 IPv6 Static Routing Configure the parameters relevant to static routing as required. For details of the parameters, see Table 3-9. Click Apply to save and apply the configuration. Table 3-9 Parameters for the IPv6 Static Routing Item Description The destination IP address to be accessed by the host.
  • Page 56 HG6543C Product Manual Figure 3-19 Key Parameters for Voice Configuration Configure the key VoIP parameters as required. For details of the parameters, see Table 3-10. Click Apply to save and apply the configuration. Table 3-10 Key Parameters for Voice Service...
  • Page 57 3 Web Configuration Guide Figure 3-20 Basic Parameters for Voice Configuration Configure the basic VoIP parameters as required. For details of the parameters, see Table 3-11. Click Apply to save and apply the configuration. Table 3-11 Basic Parameters for Voice Service Description Item The VoIP protocol type, configured in Key Parameters.
  • Page 58 HG6543C Product Manual Table 3-11 Basic Parameters for Voice Service (Continued) Description Item The IP address or domain name of the standby register server. The Second Register port number range is 1024 to 65535, and the default setting is 5060.
  • Page 59 3 Web Configuration Guide Figure 3-21 Advanced Voice Configuration Configure the advanced VoIP parameters as required. For details of the parameters, see Table 3-12. Click Apply to save and apply the configuration. Table 3-12 Advanced Parameters for Voice Service Description Item The default PT value in RFC2833.
  • Page 60 HG6543C Product Manual Table 3-12 Advanced Parameters for Voice Service (Continued) Description Item The heartbeat time length. The value range is 1 to 43200. Alive Interval The fax mode. The options include Transparent and T38. The Fax Mode default setting is Transparent.
  • Page 61 3 Web Configuration Guide Figure 3-22 Digitmap and Time Length Configure VoIP time length parameters. For details of the parameters, see Table 3-13. Click Apply to save and apply the configuration. Table 3-13 Parameters of Digitmap and Time Length Description Item The digitmap matching mode.
  • Page 62 HG6543C Product Manual Table 3-13 Parameters of Digitmap and Time Length (Continued) Description Item The howler tone time. The value range is 1 to 254 (s), and the default Hang Up Time setting is 60. The busy tone time. The value range is 1 to 254 (s), and the default setting Busy Time is 40.

  • Page 63: Security

    3 Web Configuration Guide Configure parameters of voice ports, including priority, coding mode and RTP packetization period, as shown in Table 3-14. Click Apply to save and apply the configuration. Table 3-14 Coding Parameters Description Item The coding mode. The options include G.711MuLaw, G.711ALaw, G.723.1, Mode G.729 and G.722.
  • Page 64 HG6543C Product Manual Select Security in the navigation bar and select Firewall Firewall Control in the left link bar to open the firewall enabling page, as shown in Figure 3-24. Figure 3-24 Firewall Control Select to Enable or Disable the firewall as required.
  • Page 65 3 Web Configuration Guide Figure 3-25 IPv4 Filtering Configure the parameters relevant to filtering as required. For details of the parameters, see Table 3-15. Click Apply to save and apply the configuration. Table 3-15 Parameters for IP Address Filtering Description Item Select the filtering mode.
  • Page 66 HG6543C Product Manual Table 3-15 Parameters for IP Address Filtering (Continued) Description Item Enter the IP address at the WAN side if the direction is LAN->WAN. Dst IP Enter the IP address at the LAN side if the direction is WAN->LAN.
  • Page 67 3 Web Configuration Guide Configure the parameters relevant to filtering as required. For details of the parameters, see Table 3-16. Click Apply to save and apply the configuration. Table 3-16 Parameters of IPv6 Filtering Description Item Select the uplink filtering mode. White List indicates that the data complying with the rules in the filtering rule table will be allowed Uplink...
  • Page 68 HG6543C Product Manual Select Security in the navigation bar and select Firewall URL Filtering in the left link bar, and then click Add to open the URL filtering table configuration page, as shown in Figure 3-27. Figure 3-27 URL Filtering Configure the parameters relevant to filtering as required.
  • Page 69 3 Web Configuration Guide Table 3-17 Parameters for URL Filtering Parameters (Continued) Description Item The ending time of the filtering rule. End Time Enables or disables this filtering rule. The options include Disable and Enable Enable. 3.4.1.5 3.4.1.5 DHCP Filtering Forbid or allow the user device configured with the MAC address to obtain an IP address in the DHCP mode to prevent DOS attacks.
  • Page 70 HG6543C Product Manual Table 3-18 Parameters for DHCP Filtering Description Item DHCP Filtering Enables or disables the DHCP filtering. Enable Select the filtering mode. The white list and black list modes are configured globally and cannot be enabled Click the Apply simultaneously.
  • Page 71 3 Web Configuration Guide 3.4.1.7 3.4.1.7 MAC Address Filtering One user device may have multiple IP addresses but only one MAC address. The user device access authority in the LAN can be controlled effectively by setting the MAC address filtering. After the fire wall is enabled, the pre-set rules will take effect, and the MAC addresses that meet the filtering criteria will be filtered.
  • Page 72 HG6543C Product Manual Table 3-19 Parameters for MAC Address Filtering (Continued) Description Item Select the filtering mode. The white list and black list modes are configured globally and cannot be enabled simultaneously. White List indicates that the data complying MAC Filtering...
  • Page 73 3 Web Configuration Guide Figure 3-31 IPv6 MAC Filtering Configure the parameters relevant to filtering as required. For details of the parameters, see Table 3-20. Click Apply to save and apply the configuration. Table 3-20 Parameters for IPv6 MAC Address Filtering Description Item IPv6 MAC...

  • Page 74: Remote Control

    HG6543C Product Manual Table 3-20 Parameters for IPv6 MAC Address Filtering (Continued) Description Item The ending time of the filtering rule. End Time Enables or disables this filtering rule. The options include Disable and Enable Enable. 3.4.2 3.4.2 Remote Control Enable or disable the remote access control.
  • Page 75 3 Web Configuration Guide Select Security in the navigation bar and select Route QOS QOS Enable in the left link bar to open the route QoS enabling page, as shown in Figure 3-33. Figure 3-33 Enabling Route QoS Select to Enable or Disable the route QoS function as required. Click Apply to save and apply the configuration.

  • Page 76: Acl Configuration

    HG6543C Product Manual Configure the parameters relevant to QoS according to the requirement. For details of the parameters, see Table 3-21. Click Apply to save and apply the configuration. Table 3-21 Parameters of Route QoS Configuration Item Description Type Select the priority type. The default setting is DSCP.
  • Page 77 3 Web Configuration Guide Select Enable and set ACL Mode and ACL Type. Then click Add to open the ACL rule list configuration page, as shown in Figure 3-36. Figure 3-36 ACL Configuration Rule Configure parameters relevant to filtering as required. For details of the parameters, see Table 3-22.

  • Page 78: Dynamic Dos

    HG6543C Product Manual Table 3-22 Parameters for ACL Configuration (Continued) Description Item The number of the LAN port(s) subject to the ACL rule. The options include Port ALL and 1 to 4. The IP address of the accessed user device.

  • Page 79: Application

    3 Web Configuration Guide Figure 3-38 HTTPS Select to Enable or Disable the HTTPS function as required. Caution: After enabling the HTTPS function, log into the Web GUI. The protocol type in URL should be https and the management IP address should be added with the port number 4433, e.g.

  • Page 80: Ddns

    HG6543C Product Manual Select to Enable or Disable the VPN transparent transmission channel as required. Click Apply to save and apply the configuration. 3.5.2 3.5.2 DDNS The DDNS server transforms the dynamic IP address at the WAN side of the ONT into a static domain name.

  • Page 81: Port Forwarding

    3 Web Configuration Guide 3.5.3 3.5.3 Port Forwarding Port forwarding can generate the mapping between the WAN port IP address / common port number and the LAN server IP address / private port number. In this way, all the accesses to a certain service port at this WAN port will be re-directed to the corresponding port of the server in the designated LAN.

  • Page 82: Nat

    HG6543C Product Manual Table 3-24 Parameters for Port Forwarding (Continued) Item Description The range of the LAN ports for forwarding. If only one port exists, enter Private Port the same port number. The protocol used for the port to forward data packets. The options Protocol include ALL, TCP and UDP.

  • Page 83: Upnp

    3 Web Configuration Guide Configure relevant parameters according to the requirement. For details of the parameters, see Table 3-25. Click Apply to save and apply the configuration. Table 3-25 Parameters for NAT Configuration Description Item The WAN connection bound with the NAT rule. Description The NAT rule name.

  • Page 84: Dmz

    HG6543C Product Manual 3.5.6 3.5.6 When the ONT is working in the routing mode, enable the DMZ function if a host at the WAN side needs to access a certain host at the LAN side. The ONT will forward all the IP packets from the WAN to the designated DMZ host.
  • Page 85 3 Web Configuration Guide Ping test: Test whether the router is normally connected with the target host or another device. Traceroute test: Check the condition of the route from the router to the target host. Select Application in the navigation bar and select Diagnosis Diagnosis in the left link bar to open the network diagnosis page, as shown in Figure 3-45.

  • Page 86: Management

    HG6543C Product Manual Figure 3-46 Nat Session Management This section introduces how to perform user management, device management and log management in the Web GUI. 3.6.1 3.6.1 User Management User management includes user account management and maintenance account management. 3.6.1.1 3.6.1.1...
  • Page 87 3 Web Configuration Guide Figure 3-47 User Account Management Add or delete a common user account or modify the password of a common user account as required. Click Apply to save and apply the configuration. 3.6.1.2 3.6.1.2 Maintenance Account Management Users can modify the username and password of the current account.

  • Page 88: Device Management

    HG6543C Product Manual 3.6.2 3.6.2 Device Management The ONT provides multiple device management functions such as restoring some of the configuration data, restoring all configuration data, local upgrade, configuration backup, FTP server, device reboot, and NTP time calibration. 3.6.2.1 3.6.2.1...
  • Page 89 3 Web Configuration Guide Click Restore All and then click OK in the alert box that appears. Wait until the configuration data are completely restored. 3.6.2.3 3.6.2.3 Local Upgrade Select the local file and upgrade the ONT software. During upgrade, do not power off the device or perform other operations to prevent damage to the device.
  • Page 90 HG6543C Product Manual Figure 3-52 Configuration Backup Configure parameters relevant to file backup. For details of the parameters, see Table 3-27. Click Apply to save the configuration backup file. Table 3-27 Parameters for Configuration Backup Item Description Username The FTP username.
  • Page 91 3 Web Configuration Guide Enable or disable the FTP server function according to the requirement.Select Enable and then enter the Username and Password for connection with the FTP server. Click Apply to save and apply the configuration. 3.6.2.6 3.6.2.6 Device Reboot Select Management in the navigation bar.

  • Page 92: Log Management

    HG6543C Product Manual Figure 3-55 NTP Time Calibration Configure parameters relevant to the NTP time calibration. For details of the parameters, see Table 3-28. Click Check Time to save and apply the configuration. Table 3-28 Parameters for NTP Time Calibration...
  • Page 93 3 Web Configuration Guide Select Management in the navigation bar. Select Log Log from the left link bar to open the log information page, as shown in Figure 3-56. Figure 3-56 Version: A...

  • Page 94: Handling Common Problems

    Handling Common Problems This chapter introduces how to handle common problems encountered in equipment operation and service test. Power Status Indicator LED Extinguished Register Status Indicator LED Extinguished Optical Signal Status Indicator LED Blinking Ethernet Interface Status Indicator LED Extinguished Failing to Detect the ONT Using Wi-Fi Failing to Access Local Web Login GUI and Failing to Ping 192.168.1.1 Failing to Access Internet Using the LAN Port...

  • Page 95: Power Status Indicator Led Extinguished

    4 Handling Common Problems Power Status Indicator LED Extinguished Handle the problem according to the procedures below. Check whether the mains supply is normal. Check whether the power adapter matches the device. Check whether the power button is pressed down. Check whether the power cable connection is normal.

  • Page 96: Failing To Detect The Ont Using Wi-Fi

    HG6543C Product Manual Check whether the network cable is damaged or connected incorrectly. Check whether the color-coding scheme of the network cable is incorrect; if so, replace it with a standard CAT-5 twisted pair network cable. Check whether the network cable length exceeds the allowed range (100 m).

  • Page 97: Failing To Access Internet Using Wi-Fi

    4 Handling Common Problems If the computer obtains an IP address automatically, check whether the computer has obtained an IP address in the network segment of 192.168.x.x. Contact the personnel in the network management center to check whether the WAN is connected correctly and bound with the LAN port. Failing to Access Internet Using Wi-Fi Handle the problem according to the procedures below.
  • Page 98 Standards and Protocols Classification Standard Number Title Gigabit-capable passive optical networks (GPON): ITU-T G.984.1 General characteristics Gigabit-capable Passive Optical Networks (GPON): ITU-T G.984.2 Physical Media Dependent (PMD) layer specification GPON Gigabit-capable Passive Optical Networks (G-PON): ITU-T G.984.3 Transmission convergence layer specification Gigabit-capable passive optical networks (G-PON): ITU-T G.984.4 ONT management and control interface specification...
  • Page 99 5 Standards and Protocols Classification Standard Number Title Enabling Network Throughput Performance Tests and TR-143 Statistical Monitoring Pulse code modulation (PCM) of voice frequencies ITU-T G.711 Wideband embedded extension for G.711 pulse code ITU-T G.711.1 modulation 7 kHz audio-coding within 64 kbit/s ITU-T G.722 Dual rate speech coder for multimedia ITU-T G.723.1...
  • Page 100 Appendix A Abbreviations Optical Network Terminal FTTH Fiber To The Home Gigabit-capable Passive Optical GPON Network Optical Distribution Network Optical Line Termination MTBF Mean Time Between Failure Dynamic Bandwidth Allocation Extensible Markup Language GPON Encapsulation Mode Asynchronous Transfer Mode Operation, Administration And Maintenance Forward Error Correction Time Division Multiple Access...
  • Page 101 Appendix A Abbreviations Demilitarized Zone Address Resolution Protocol Universal Plug and Play UPnP Denial of Service Uniform Resource Locator Hyper Text Transfer Protocol over HTTPS Secure Socket Layer CATV Cable Antenna Television Session Initiation Protocol VoIP Voice over Internet Protocol Real-time Transport Protocol SSID Service Set Identifier...
  • Page 103 Product Documentation Customer Satisfaction Survey Thank you for reading and using the product documentation provided by FiberHome. Please take a moment to complete this survey. Your answers will help us to improve the documentation and better suit your needs. Your responses will be confidential and given serious consideration.
  • Page 104 12. Additional comments about our documentation or suggestions on how we can improve: Thank you for your assistance. Please fax or send the completed survey to us at the contact information included in the documentation. If you have any questions or concerns about this survey please email at edit@fiberhome.com...

Table of Contents

Save PDF