Panduit CT-720 Operating Instructions

CT-720 INSTALLATION TOOL: OPERATING INSTRUCTIONS
COPPER LUGS AND SPLICES
DIE COLOR
DIE
CODE AND
PART
INDEX
NUMBER
NUMBER
RED P21
BLUE P24
CD-720-1
GREY P29
BROWN P33
GREEN P37
PINK P42
CD-720-2
BLACK P45
ORANGE P50
PURPLE P54
CD-720-3
YELLOW P62
CD-720-4 WHITE P66
CD-720-5 RED P71
CD-720-6 BLUE P76
CD-720-7 BROWN P87
RED PV8
BLUE PV6
CD-720PV8-2
YELLOW PV4
RED PV2
0"
DIE SELECTION:
•
MATCH COLOR ON COMPRESSION POCKET TO
COLOR ON CONNECTOR — SEE CHART ABOVE.
DIE INSTALLATION:
•
TO INSTALL CD-720 SERIES DIES, OPEN HANDLES
UNTIL FULLY EXTENDED.
•
INSERT DIE INTO RECESS IN TOOL HEAD WITH
SELECTED COMPRESSION POCKET FACING JAW.
•
ALIGN HOLE IN DIE WITH DIE RETENTION SCREW
AND FIRMLY TIGHTEN SCREW.
•
CHECK THAT TOOL IS PROPERLY ADJUSTED AS
INSTRUCTED.
© 2015 Panduit Corp.
NUMBER OFCOMPRESSIONS
PER WIRE
WIRE
LCA/LCAN LCB
SIZE
LCAS
LCD/LCDN LCC/LCCN
SCSS
SCS SCL
8 1 1 2
6 1 1 2
4 1 1 2
2 1 1 2
1 1 1 2
1/0 1 1 2
2/0 2 2 3
3/0 2 2 3
4/0 2 2 3
250 2 2 4
300 2 — 4
350 2 — 4
400 2 — 4
500 2 — 4
#8
Pan-Term
#6
VINYL INSULATED TERMINALS
#4
ONLY
#2
TOOL ADJUSTMENT:
•
ADJUST TOOL WITH ANY CD-720 DIE INSTALLED BY LAYING TOOL ON A FLAT SURFACE AND CLOSING
HANDLES UNTIL JAW JUST CONTACTS DIE.
•
MEASURE DISTANCE BETWEEN TIPS OF GRIPS AS SHOWN IN FIGURE 1. TOOL IS PROPERLY ADJUSTED WHEN
DISTANCE MEASURED IS BETWEEN 10" (254 mm) AND 13" (330 mm). USE SCALE PROVIDED ABOVE.
•
IF LESS THAN 10", TURN ADJUSTMENT SCREW CLOCKWISE; IF MORE THAN 13", TURN COUNTERCLOCKWISE.
FIGURE 2
ALUMINUM LUGS AND SPLICES
DIE COLOR
DIE
CODE AND WIRE
PART
INDEX SIZE
NUMBER
NUMBER
— —
GREY P29 6
CD-720-1
— —
— —
GREEN P37 4
PINK P42 2
CD-720-2
GOLD P45 1
TAN P50 1/0
OLIVE P54 2/0
CD-720-3
RUBY P62 3/0
CD-720-4 WHITE P66 4/0
CD-720-5 RED P71 250
CD-720-6 BLUE P76 300
CD-720-7 BROWN P87 350
TOOL OPERATION:
•
INSERT BARED CONDUCTOR INTO CONNECTOR.
•
LOCATE CONNECTOR IN COMPRESSION POCKET SO THAT DIE IS BETWEEN COMPRESSION BANDS ON
CONNECTOR.
•
COMPLETELY CLOSE HANDLES. REPEAT OPERATION FOR CONNECTORS THAT REQUIRE MORE THAN
ONE COMPRESSION.
TOOL MAINTENANCE:
LUBRICATE PIVOT PINS ONCE A MONTH WITH SAE 20 OR EQUIVALENT MACHINE OIL.
Page: 1 of 2
NUMBER OF COMPRESSIONS
PER WIRE
LAA LAB SA
— — —
2 — 2
— — —
— — —
2 — 2
3 — 3
3 — 3
3 3 3
3 3 3
4 4 4
4 4 4
4 4 4
4 4 4
4 4 4
10"
FIGURE 1
13"
WARNING:
DO NOT USE THIS TOOL
ON LIVE ELECTRICAL
CIRCUITS!
PA24517A01_ 03
11/2015