Stereoping Synth Programmer Owner's Handbook Manual
For rhodes chroma
Hide thumbs
Also See for Synth Programmer:
- Owner's handbook manual (22 pages) ,
- Operation manual (20 pages) ,
- Owner's handbook manual (24 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stereoping Synth Programmer
Summary of Contents for Stereoping Synth Programmer
- Page 2 ___________________________________________________________________________________________________________2 Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018...
-
Page 3: Table Of Contents
Button 'PEEK'....................................10 Buttons 'EDIT A' and 'EDIT B'..............................10 Button 'Relative'...................................11 6.PREFS and MIDI BYPASS MODE........................12 Midi Bypass Mode..................................12 7.Updating Firmware............................13 8.Imprint................................14 Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 4: General Features Of The Synth Programmer
Technical handling The Synth Programmer was built to be used in a comfortable music studio environement. You can operate it under free skies of course. But please keep in mind, it uses electricity for proper operation and therefore is quite sensitive to water, drinks or other fluids. -
Page 5: Connections And Integration Into Your Setup
You can use any ordinary 9 Volt DC powersupply to operate your controller. The connector should have Plus on it's center pin and Ground - sometime labeled as 'Minus' - on the outside. The Synth Programmer has a protection diode for not taking damage if the polarity of the power supply is wrong, it just won't work. The current of the PSU should at least offer about 200 mA (=0.2 A). -
Page 6: Settings And Workflow
The Programmer does not offer any Randomizer nor an Initialising program. Both is already built in the CC+ Interface: SET SPLIT & 38 for entering the Randomizer • SET SPLIT & 39 for an initialising program ('SCRATCH PATCH') • Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 7: Brief Overview
Press PATCH to jump into PATCH Mode. This is where to recall Programs you want to work on. Details about PATCH Mode will be handled in chapter 4. PATCH Mode Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 8: Patch Mode
Pressing the button labeled XIT leaves Patch mode and heads back to normal PLAY mode. Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 9: Play Mode
If A and B are selected, only the source of channel A will be shown, even if channel B got set another modulation source. Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 10: Dials With Double Function
Depending on which one is active, the changes will be sent to channel A or channel B. Of course you can select both to send the changes to both channels at the same time. Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 11: Button 'Relative
39 CUTOFF Tune • All other parameters behave as if Relative is off: turning the knob sets A and B to the same value. Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 12: Prefs And Midi Bypass Mode
Programmer would not be in between at all. This mode is quite useful if you want to dump some soundbanks into the Matrix. You can leave MIDI BYPASS MODE at any time pressing PREFS again. Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 13: Updating Firmware
7. Updating Firmware The day may come you want to update your edition or try out another. Your Synth Programmer offers a firmware update mode for this. After entering this mode you just send a firmware-file into the controllers MIDI IN 2 jack. -
Page 14: Imprint
Stereoping is a registered trademark of Gregor Zoll, Germany. Address Gregor Zoll Musikelektronik Hermann-Voss-Str. 21 59872 Meschede Germany E-Mail h e llo@stereoping. com Homepage http s ://www.stereoping.com Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018... -
Page 15: Stereoping Germany, Meschede
Imprint_________________________________________________________________________________________________15 Synth Programmer for Rhodes Chroma – Owner's handbook V1.0 – 05/2018 © Stereoping Germany, Meschede 2018...
Need help?
Do you have a question about the Synth Programmer and is the answer not in the manual?
Questions and answers