Elan Z600 Quick Reference Manual

600 COMM CONTROLLER QUICK REFERENCE GUIDE
See reverse side for Z600 connections when NOT using a PZ6 Precision Panel
Z600 to PZ6 PRECISION PANEL FRONT PANEL CONNECTIONS
ELAN
C4545
Interconnect
to to
Cables
PZ6 PZ6
'Control' 'Relay'
Z600 TO PZ6 PRECISION PANEL REAR PUNCHDOWN CONNECTIONS
TELCO CONNECTIONS
Telco Connector
GND
nc
Telephone
TIPTELCO
Service IN
RINGTELCO
TIPPHONE
to Punch-
RINGPHONE
down Block
nc
P&DB
DOOR SPEAKER ASSEMBLY CONNECTIONS
PZ6 Door 4 twisted-pair
Speaker Connector shielded cable
w/ drain wire
M+ Blue
(min. 24 AWG)
M- Wh/Blue
(max. length 400')
DB- Orange
L+ Wh/Orange
L- Green
DB+ Wh/Green
DS+
Brown
Wh/Brown
DS-
DRAIN
WIRE
Complete Z Series Installation Manuals for each Z Series component are available for download from the ELAN Web Site, www.elanhomesystems.com
used for from Z630 to Z630
stand-alone Source #1 P&DB IN
applications or dedicated
(see Z600 MOH source
Installation Manual)
OVERRIDE CONNECTIONS
VCO Connector
VC-
ELAN Volume VC+
Control w/ VC-
Override VC+
VC- VC-
VC+ VC+
VC-
VC+
NOTE: Plug the Z027 +12VDC Power Supply
into the VCO jack on the front of the PZ6.
DUAL PZ6 INTERCONNECTS
Door
Station
Blue
M+
Wh/Blue
M -
Orange DB-
Wh/Orange L+
Green
L-
Wh/Green
DB+
Cut
DRAIN
Brown
DS+
WIRE
Wh/Brown
DS-
to Electronic
N.O.
Door Latch COM
to to to
PZ6 PZ6 PZ6
DS1 DS2 'Phone'
RELAY CONNECTIONS
Relay Connector
Relay-Controlled
R1 COM
Device
R1 N.O.
R2 COM
R2 N.O.
R3 COM
R3 N.O.
R4 COM Relay-Controlled
R4 N.O. Device
PZ6 #1 PZ6 #2 PZ6 #1 PZ6 #2
Zone Zone Telco Telco
Connector Connector
Connector Connector
VC- VC- GND
GND
GND GND nc nc
+12V +12V
TIPTELCO TIPTELCO
485- 485-
RINGTELCO RINGTELCO
485+ 485+
TIPPHONE TIPPHONE
nc nc
RINGPHONE
RINGPHONE
IR
IR nc
nc
VC+ VC+ P&DB P&DB
any of the PZ6 Zone
Connectors may be used
Z600 FRONT PANEL ADJUSTMENTS
(Pull back left side of front panel strip to access)
Door Chime Loop-
Thru Level
Page
Loop-Thru
Level
DIP SWITCH SETTINGS
#
1. (Factory Default: )
to
# *
PZ6
Selects whether the or key
'Telco'
is used to initiate ELAN telcomm
features.
2. (Factory Default: 65ms)
Switch to 85ms only if experiencing
intermittent drop-outs during a phone
conversation.
3. (Factory Default: 75ms)
Switch to 1.25 sec. only if experiencing
trouble with Call Waiting functions.
DC
4. (Factory Default: +3dB)
Power
Switch to '0' if the Door Speaker is too
Supply
loud or you are experiencing
feedback from the Door Speaker.
5. (Factory Default: +3dB)
Switch to '0' dB if the Door Mic is too
loud or you are experiencing feedback
from the Door Mic.
Always use Telephone Line Surge Protection
between the incoming telephone service and
the Z600 Communications Controller.
Page & Door Chime
Output Level
MOH
Input Level
*
1 2 3 4 5
#
(Factory Default settings shown)
P/N 9900006 April 2003