FIBARO FGR221 Operating Manual

ENG
FIBARO provides many advantages when compared to similar
systems. In general, radio systems create a direct connection
The advantage of FIBARO system is that its devices apart from
achieved through other intermediate devices.
OPERATING MANUAL
ROLLER SHUTTER CONTROLLER
confirmation of its reception. This operation confirms their status so
FGR221 v1.4
to check whether they are active. Safety of the FIBARO system
wired systems.
Remotely controlled Roller Shutter Controller of FIBARO system is
frequency. Every FIBARO system has its own unique identification
designed to control motors of roller shutters, awnings, etc.
It has the function of detecting the current state of a controlled
device, e.g. position of roller shutter.
Specifications
Power supply FIBARO generates a dynamic network structure. After FIBARO
system is switched on, the location of its individual components is
Power of supplied motor
signals received from devices operating in a "mesh" network.
In accordance with EU
standards
shutter connected to its terminals using radio waves, controllers and
Temperature limits
Operational temperature
II Assembling Roller Shutter Controller
Radio protocol
Radio Frequency
Range
1. Before installation ensure that the voltage supply is
Technical Information disconnected.
2. Connect the Roller Shutter Controller in accordance with the
diagram on Fig. 1
3. Place the device in the electrical box.
4. Arrange the antenna (tips are presented below diagrams of
fig. 1)
DANGER
Danger of electrocution! All works on the device
DANGER
Danger of electrocution. Even when the device is
Any works introducing changes into the
always performed with disconnected voltage
Fig.1 Circuit diagrams for the Roller Shutter Controller
TIPS
i
recommended values.
NOTES FOR THE DIAGRAM:
Connect only in accordance with the diagram
presented i n t he m anual. I mproper c onnections m ay
TIPS FOR ARRANGING THE ANTENNA:
i
Locate the antenna as far from metal elements as
order to prevent interferences.
i
Metal surfaces in the direct vicinity of the antenna
may impair signal reception!
i
operates
Note!
i
S1 terminal operates with the shutter motor output
terminal, operates with the shutter motor output O2.
down.
Note!
i
DICTIONARY:
radio system
Danger of electrocution.
III Starting the operation of the
Roller Shutter Controller
1. Installing the Roller Shutter Controller
STEP 1
Connect the device in accordance with the circuit diagram presented
[Adding/ Removing] of the Roller Shutter Controller [to/ from]
L Z-­wave network
N
STEP 2
Home Center controller, as the adding mode requires direct
communication with the controller.
STEP 3
Identify key no. 1. If the device is connected in accordance with the
diagram shown in Figure 1, this will the key that raises the roller
shutter.
N
STEP 4
S1 S2 O1 O2 L N
M
Roller STEP 5
B
Shutter
the device.
WARNING!
i
The Roller Shutter Controller cancels the "learning"
mode after key no. 1 is pressed once. Therefore,
pressing key no. 1 four times will not add the devices
to the network.
WARNING!
i
switches, ensure that all switch contacts are open
to the network.
During the installation, it is recommended to use a
The Roller Shutter Controller enables user to associate three
mono-­stable keys or push-­ button B. groups.
Group I
STEP 6
The controller indicates that the device is correctly added to the
network, (see the manual of Home Center controller
Group II
Group III for controllers such Home Center for state reporting
devices, and 7 MultiChannel devices in group no. 1 and no. 2, group
the network controller. It is recommended to use up to 10 devices, as
2. Resetting the Roller Shutter Controller
The Roller Shutter Controller provides two methods for resetting.
Method I :
devices added to associated groups may take even a few minutes
Method II
once S1 key and then holding key S2.
i
3. Controlling the Roller Shutter Controller by
mono-­stable or bi-­stable switches.
Mono-­stable switch (after releasing the push-­button a spring
automatically pushes back and disconnects the button )
FGR221 Roller Shutter Controller supports the operation of
assigned for the action.
two or more circuits inside one physical unit.
Bi-­stable switch (operates as a two-­position switch, it has no
spring that would push back the device after releasing manual
pressure)
V Configuration
The Roller Shutter Controller allows user to configure the following
4. Controlling the Roller Shutter Controller using
i
entering an appropriate value into configuration register no. 1
5. Controlling the Roller Shutter Controller using
OFF. default value 0
Fibaro system controller
255
0
1
2
Parameter no. 10 -­ Turning off the shutter positioning function
default value 0
Options for changing parameter 0, 1
0
1
Parameter no. 14 -­ Switch type connector, you may choose
between mono-­stable and bi-­stable switches default value 0
Options for changing parameter 0, 1, 2
Parameter no. 20 -­ Saving the position "Favourites"
IV Association
or scene
Possibility to change the configuration of the following
parameters [30 -­ 33].
0
WARNING!
frames
i
Association ensures direct transfer of control
1
after detecting an alarm
without participation of the main controller.
2
after detecting an alarm
Parameter no. 30 -­ General Alarm, set for shutter no. 1
Parameter no. 31 -­ A larm of flooding with water, set for relay the
shutter.
Parameter no. 32 -­ Smoke, CO, CO2 Alarm. Set for the roller
shutter.
Parameter no. 33 -­ Temperature Alarm, set for roller shutter
VI Additional Functionality
WARNING!
commands and a new command is issued, then the
Operating alarm data frames
current one command transmission is interrupted to
send new commands.
The device may respond in the following manner to received
WARNING!
Entering incorrect parameters may cause incorrect
operation of the Roller Shutter Controller. frames
after detecting an alarm
shutter after detecting an alarm
Position indicating
detect the current position of roller shutters, awnings and similar
devices. For proper operation of the mechanism, it is necessary to
use a motor with mechanical limit switches. Correct operation of the
position detecting mechanism, when using motor with overload
VII Operating the Shutter Roller Controller
The Roller Shutter Controller may be operated using the
following control elements:
VIII Procedures for malfunctions
The device does not respond to a pre-­programmed transmitter:
the programming process.