Advertisement
NOTE: Although mounting the communicator on the control panel is preferred, it may
also be wall mounted. When wall mounting, please follow these guidelines:
• Use both mounting holes to fasten.
• Route the wiring through the communicator's rear or bottom wiring access hole.
• Ensure all wiring splices are located within the communicator's enclosure.
• Secure all wiring with ties as necessary.
• Follow the recommended wire gauge sizes.
2. Program and Register the Communicator
You can quickly program and register the communicator by using the
AlarmNet Direct website, using the 7720P Programming Tool, or by phone.
In addition, after you program the communicator, you can register it by
using the Test Message / Registration switch.
Using the AlarmNet Direct website to program and register:
1. Log in as you did to activate the SIM.
2. Refer to the online help file to program the new device.
3. Register the communicator.
4. DONE.
Using the 7720P Programming Tool to program and register:
1. This procedure will program the GSMX4G for basic control panel
communications. For advanced features and remote services refer to
the product's Installation and Setup guide.
2. Ensure the system is powered up and connect the programming tool to
the communicator.
3. Accept all default settings except the following prompts which need to
be answered. Then exit the programming mode.
PROMPTS
OPTIONS
9
• ECP
Device Mode
(ECP)_
• 4204 Emu
• Two
4204s
NOTE: Account information is provided by the central station. Enter this
information in prompts 12, 13 and 14.
12
[01-99]
Primary City
ID
(??)_
13
[01-FE]
Primary CS ID
(??)_
14
[0001-9999]
Primary Sub
ID (????)_
WARRANTY Go to:
http://www.security.honeywell.com/hsc/resources/wa/
DOCUMENTATION AND ONLINE SUPPORT Go to:
Ê800-10939bŠ
800-10939 1/12 Rev. F
DESCRIPTION
Press the [space] key to scroll through
the modes of operation. Choose the
default ECP mode and press [ENTER].
NOTE: For other modes and advanced
features, see the Installation and Setup
guide.
Enter the 2-digit primary city ID,
01-99 (decimal).
Enter the 2-digit primary central station
ID number, 01-FE (HEX).
Enter the 4-digit subscriber account
number, 0001-9999 (decimal).
http://www.security.honeywell.com/hsc/resources/MyWebTech/
Minimum Wire Gauge
#22
#20
#18
#16
4. The interactive registration feature allows the installer to register the
communicator through a series of keyboard commands on the
7720P Programming Tool. This method of registration lets the
installer monitor the registration process.
Once the programming is complete, press the
Registering
...
[Shift] plus the up arrow [↑] key on the 7720P.
The registration message is sent and the unit
waits for the acknowledgment.
If this is a new installation and the city, central
Registration
station, and customer numbers have been
SUCCESS
correctly entered, the GSMX4G is registered and
this message is displayed.
The communicator is now in full service and
available for alarm reporting to the central
station.
Using the Test Message / Registration switch to register:
After programming, initiate the registration
sequence by clicking the Test Message /
Registration switch three times.
CELLULAR STATUS LED
TEST MESSAGE /
REGISTRATION
Switch
Using the Phone to program and register:0
You can program and register the communicator by calling the
AlarmNet Support at 1-800-222-6525 (Option 1). (Monday–Friday 8:00
am to 9:00 pm, Saturday 9:00 am to 5:30 pm EST) You will need the
following information:
• MAC ID and CRC (located on the box and inside the communicator).
• Subscriber information (provided by the central station), including a
city code, CSID, and subscriber ID.
• When Instructed to do so, triple click the TEST MESSAGE /
REGISTRATION switch.
Cellular Status LED information:
Voice Session – Short blink every second
Data Session – Short blink every 2 seconds
Connected to Cell network – Short blink every 4 seconds
No or deactivated SIM – Long blink every second
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2012 Honeywell International Inc.
Distance from Control Panel
75 ft (23m)
120 ft (37m)
170 ft (52m)
270 ft (82m)
www.honeywell.com/security
Advertisement
