Advertisement
Quick Links
Advertisement
Related Manuals for Converters.TV 15437
Summary of Contents for Converters.TV 15437
- Page 1 4K UHD Matrix 8×8 HDMI over - # 15437 HDBaseT with 24V PoC Operation Manual...
- Page 2 Introduction The 4K2K 8 by 8 HDMI Matrix over CAT5e/6/7 supports the transmission of video (resolutions up to 4K2K Full HD), multi-channel digital audio and control via IR, RS-232, Telnet or Web GUI from eight high definition sources to eight outputs over a single CAT5e/6/7 cable (up to 60m) for each output.
- Page 3 System Requirements • HDMI equipped source devices, connect with HDMI cables or DVI equipped source, connect with DVI to HDMI cables • HDMI equipped displays (TVs or monitors) or HDMI equipped AV receivers, connect with HDMI cables • Industry standard CAT5e/6/7 cables •...
- Page 4 Rear Panel 1. LAN: Connect to an active network for LAN serving and Telnet and Web GUI control (refer to Sections on Telnet and Web GUI). When the Matrix or any compatible LAN equipped receivers are connected to a network, this allows the network access (including internet access if available) to be shared between the Matrix and all connected receivers.
- Page 5 Connect from these CAT outputs to the CAT input port of the receiver units with a single CAT5e/6/7 cable for HDMI Audio/Video and IR/RS-232 control signal transmission. HDMI IN 1~8: Connect to the HDMI input source devices such as a DVD player or a Set- top Box with HDMI cable or DVI to HDMI cable.
- Page 6 IR Cable Pin Assignment D-Sub 9-Pin Assignment HDBaseT 8x8 Matrix Remote Control Assignment Assignment ► ◄ Baud Rate: 19200 bps Data bit: 8 bits Parity: None Stop Bit: 1 Flow Control: None...
- Page 7 RS-232 and Telnet Commands Command Description A1~A8 Switch Output A to 1~8 B1~B8 Switch Output B to 1~8 C1~C8 Switch Output C to 1~8 D1~D8 Switch Output D to 1~8 E1~E8 Switch Output E to 1~8 F1~F8 Switch Output F to 1~8 G1~G8 Switch Output G to 1~8 H1~H8...
- Page 8 UARTSW0 Switch output's UART to MCU. Restoring RS-232 control to the Receiver output back to Matrix. UARTBAUD? Display all the outputs UART baud UARTSW? Display the UART switching state Display all the available commands Quit Exit(for telnet only) Note: Any commands will not be executed unless followed by a carriage return. Commands are case insensitive.
- Page 9 Once in the command line interface (CLI) type "telnet", the IP address of the unit you wish to control and "23", then hit enter. Note: The IP address of the Matrix can be displayed on the device's LCM monitor by pressing the Menu button twice/three times.
- Page 10 Web GUI Control On a PC/Laptop that is connected to the same active network as the Matrix, open a web browser and type device's IP address on the web address entry bar. The browser will display the device's status, control and User setting pages. Click on the 'Control' tab to control power, input/output ports, EDID and reset mode.
- Page 11 Specifications 300 MHz/9 Gbps Video Bandwidth Input Ports 8×HDMI, 9×IR Extender, 1×RS-232, 1xLAN, 1×Mini USB-B type (for firmware update only) 8×CAT5e/6/7, 9×IR Output Ports Power Supply , CE/FCC/ 24 V/6.25 A DC (US/EU standards UL certified) ESD Protection Human Body model: ±...
- Page 12 Connection Diagram...