Common Section - Kenwood NX-5700 Service Manual

4.8

Common Section

Item Condition
Panel tuning
mode
1. 1) DC voltage:13.6V
Setting 2) SSG standard modulation
[Wide] MOD:1kHz,DEV:3kHz
[Narrow] MOD:1kHz,DEV:1.5kHz
2. 1) Adj item: 1) Adj item:
Receive [RAST] [Receive Assist]
Assist Adjust:[****] 2) Adj item:
2) Adj item: [Low1]→
[Low1 RAST]→ [Low2]→
[Low2 RAST]→ [Low3]→
[Low3 RAST]→ [Center1]→
[Center1 RAST]→ [Center2]→
[Center2 RAST]→ [Center3]→
[Center3 RAST]→ [High1]→
[High1 RAST]→ [High2]→
[High2 RAST]→ [High3]
[High3 RAST]
Adjust:[****]
Press [ ] key
to store the ad-
justment val-
ue.
Press [Apply All] but-
ton to store the ad-
justment value.
3. 1) Adj item: 1) Adj item:
Transmit [TAST] [Transmit Assist]
Assist Adjust:[****] 2) Adj item:
2) Adj item: [Low1]→
[Low1 TAST]→ [Low2]→
[Low2 TAST]→ [Low3]→
[Low3 TAST]→ [Center1]→
[Center1 TAST]→ [Center2]→
[Center2 TAST]→ [Center3]→
[Center3 TAST]→ [High1]→
[High1 TAST]→ [High2]→
[High2 TAST]→ [High3]
[High3 TAST]
Adjust:[****] PTT: Press
PTT: ON [Transmit] button.
Press [ ] key
to store the ad- Press [Apply All] but-
justment val- ton to store the ad-
ue. justment value.
1-46 (No.RA020<Rev.002>)
Measurement
PC test mode Test-
equip-
ment
Adjustment
Unit Ter- Unit Parts
minal
Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Specifications
Method
[PC test mode] 2.5V±0.1V
[Automatic Adjust- [Automatic Ad-
ment] justment]
1) Press [Tune Assist After the automatic
Voltage] button. adjustment is per-
2) Press [Apply All] but- formed, verify that
ton to store the adjust- the VCO lock volt-
ment value after the age is within the
automatic adjustment voltage range
has finished. which is specified
[Manual Adjustment] by the manual ad-
[V] indicator on the PC justment.
window shows VCO lock [Manual Adjust-
voltage. Change the ad- ment]
justment value to get Press [Apply All]
VCO lock voltage within button to store the
the limit of the specified adjustment value
voltage. after all adjustment
point have been
Note:
adjusted.
Confirm the VCO lock
voltage approximately Note:
3 seconds after the The assist adjust-
adjustment value is ment value must
changed. be between from
340 to 3550.
[PC test mode] 2.5V±0.1V
[Automatic Adjust- [Automatic Ad-
ment] justment]
1) Press [Tune Assist After the automatic
Voltage] button. adjustment is per-
2) Press [Apply All] but- formed, verify that
ton to store the adjust- the VCO lock volt-
ment value after the age is within the
automatic adjustment voltage range
has finished. which is specified
[Manual Adjustment] by the manual ad-
[V] indicator on the PC justment.
window shows VCO lock [Manual Adjust-
voltage. Change the ad- ment]
justment value to get Press [Apply All]
VCO lock voltage within button to store the
the limit of the specified adjustment value
voltage. after all adjustment
point have been
Note:
adjusted.
Confirm the VCO lock
voltage approximately Note:
3 seconds after the The assist adjust-
adjustment value is ment value must
changed. be between from
340 to 3550.
/Remarks