Moxa Technologies V481-CE Quick Installation Manual

V481-CE
Quick Installation Guide
Second Edition, April 2008
1. Overview
The V481 is an industrial, ready-to-run embedded computer that supports
VGA and audio, and comes with dual LAN ports, 8 serial ports, a
CompactFlash slot, and a USB port. The V481 is based on the Intel x86
processor. The VGA interface makes the V481 especially well-suited for
industrial applications, such as SCADA, factory automation, and
applications that require an onsite HMI or monitor.
2. Package Checklist
Before installing the V481, verify that the package contains the following
items:
1 V481
Quick Installation Guide (this guide)
Document and Software CD
Din-rail Mounting Kit
100 cm RJ45-to-RJ45 cross-over Ethernet cable
20 cm Y-cable for keyboard and mouse (CBL-MiniDIN6P/6Px2-20)
Terminal block to power jack converter (includes terminal block)
Product Warranty Statement
Optional Accessories
Switching power adaptor for the V481:
60W, 24 VDC output, 100 to 240 VAC input (power cord must be
ordered separately); Order No.: 1117224250210
Power Cords:
Power cord with Australia plug; Order No.: 9199000000500
Power cord with UK plug; Order No.: 9199000000600
Power cord with Euro plug; Order No.: 9199000000700
Power cord with US straight plug; Order No.: 9199000000800,
NOTE: Please notify your sales representative if any of the above items
are missing or damaged.
3. V481 Panel Layout
The following figures show the panel layouts of the V481.
— 1 —
Rear View
Top View
Front View
LED Indicators
There are 6 LED indicators located on the front panel of the V481.
LED Name
Power
Storage
LAN1,
LAN2
P/N:1802004810011
Power Button
Power Input
Serial Ports x 8
9-36 VDC
RS-232/422/485
Speaker Audio USB 2.0 10/100 Mbps
Power LED Input
Output Host x 2 Ethernet
10/100/1000 Mpbs
PS/2
Storage LED Reset VGA
Gigabit Ethernet
LED Color LED Function
Green Power is on
No power is being received, or
Off
power error exists
Data is being written to or read
Yellow
from the storage unit
Off Storage unit is idle
Link Yellow Tx/Link
LED Off Disconnected or short circuit exists
Orange 1000 Mbps Ethernet Mode
(LAN2 Only) (Gigabit Ethernet)
Mode
LED
Green 100 Mbps Ethernet Mode
Off 10 Mbps Ethernet Mode
— 2 —
4. Installing the V481
Wall or Cabinet Mounting
The V481 has built-in "ears" for attaching the embedded computers to a
wall or the inside of a cabinet. We suggest using two screws per ear to
attach the V481 to a wall or cabinet.
DIN-Rail Mounting
An aluminum DIN-Rail mounting kit is a standard accessory. If you need
to reattach the DIN-Rail mounting kit to the V481, make sure the stiff
metal spring is situated towards the top, as shown in the following figures.
Follow Steps 1 and 2 to mount the V481 on the DIN-Rail.
STEP1: Insert the top of the STEP2: The DIN-Rail attachment
DIN-Rail into the slot just below unit will snap into place as shown.
the stiff metal spring.
metal
spring
metal
spring
DIN-Rail
DIN-Rail
To remove V481 from the DIN-Rail, simply reverse Steps 1 and 2
5. Connector Description
Power Connector
Connect the 9 to 36 VDC LPS or Class 2 power line to the V481's
terminal block. If the power is properly supplied, the Power LED will
light up.
Grounding the V481
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting the power.
ATTENTION
This product is intended to be mounted to a well-grounded mounting
surface, such as a metal panel.
Use screws on
SG: The Shielded Ground (sometimes called
top to tighten wires
Protected Ground) contact is the right most
contact of the 3-pin power terminal block
connector, as viewed from the angle shown
here. Connect the SG wire to an appropriate
Insert shielded ground
V+ V-
wire here
grounded metal surface.
DC 9-36V
— 3 —
.