CAUTION: To reduce the risk of fire, connect only to a circuit provided with the minimum branch circuit overcurrent protection requirements in accordance with the National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part I, C22.1. EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
Page 3
User Manual Rev 1.0 Repair and Maintenance Clause • All EVoCharge products do not require routine maintenance however, periodic inspections should be conducted to ensure that all parts remain in good working order and no damage exists. Do not attempt to open, disassemble, repair, tamper with, or modify any components of the products –...
User Manual Rev 1.0 Product Features EVoCharge® EVoInnovate™ Electric Vehicle Charging Station (EVSE) • J1772 AC Level 2 (208-240 VAC), 32A Continuous Rated (7.68 kW) • Adjustable Maximum Current Output (32A, 24A, 16A) to Support Multiple Circuit Ratings (40A, 30A, 20A) •...
Page 5
When power resumes after an outage, the charging station restarts automatically with a delay ranging from 120 to 720 seconds. The delay is designed to avoid impacting the utility grid when multiple charging stations are in the same area attempting to resume charging simultaneously. EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
3.2.1 Connect and Charge ..................... 20 Stop Charging ..........................20 3.3.1 Self-Monitoring and Recovery (Auto Restart) .............. 20 3.3.2 Power Outage Recovery ....................20 General Product Care and Use Information ................21 EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
Bracket is Attached to Charging Station Holder is packaged within cardboard compartment Connector & Cable Holder of charging station packaging 2 Fasteners for Charging Station Mounting Bracket Mounting Fasteners 2 Fasteners for Connector & Cable Holder EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
CAUTION: The service wiring in this section are specific to North America only. Before installing the Charging Station, identify the type of utility service connection available onsite. If you have unsure about the type of connection available at the service panel, contact your utility service provider. EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
2. Remove the Charing Station front cover by loosening the (5) Torx screws at the rear of the charging station. Five Torx screw locations to remove the Charging Station Cover EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
Page 11
6-1. Reinstall the LED wiring harness to the charging station circuit board and install the charging station font cover using the following torque force to secure the (5) Torx screws: Screw Torque 16 kgf.cm 13.88 lb-in EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
In this case, the screws should pass (install) through the middle two vertical screw holes of the mounting bracket as shown in Figures 2-1 & 2-2. EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
Page 13
4. As shown in Figures 2-3 & 2-4, mount the charging station onto the mounting bracket and secure the lock screw. 3-1. Tighten the installed M4 screw and screw washer to fix charging station on mounting bracket. 3-2. Use following torque force: Screw Torque 16 kgf.cm 13.88 lb-in EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
Page 14
5. For Plug-in (NEMA 6-50) models, Plug in the power cord to the NEMA 6-50 Wall Outlet/Receptacle. The NEMA outlet should be located no less than 20~26” from the ground or as defined by applicable state, local and national electrical codes and standards. Figure 2-5 Plug in the power cord EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
CAUTION: The LED board is attached to the charging station front cover and the charging station circuit board. Use care to not place force or strain on the wiring harness when the cover screws are removed. Failure to do so may result in damage to the charging station. EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
Page 16
National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part I, C22.1. Model Current Setting Circuit Rating Requirement EVoInnovate 40A or greater EVoInnovate EVoInnovate EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
2. The Holder can be installed at any location near the charging station. Once the holder installation location is determined, secure the holder bracket to the wall with appropriate screws x2 ( or M6). 1/4” Figure 2-9 Secure the hook EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
Page 18
User Manual Rev 1.0 3. Position the plastic holder insert face up and install into the holder bracket. Figure 2-10 Secure the holder 4. Next, rotate the holder insert down. Figure 2-11 Rotate the holder EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
Page 19
(do not overtighten). The screws ensure that the plastic holder component remains secured to the holder bracket. Figure 2-12 Lock screws 6. Insert EV charging connector into the holder. Figure 2-13 Insert EV Charging Connector into Holder EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
With the circuit breaker in the “OFF” position, wait 1-2 minutes and then switch the upstream circuit breaker back to the “ON” position • Confirm the Fault light is no longer present. If the Fault light remains, please contact EVoCharge. EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
When power resumes after an outage, the charging station restarts automatically with a delay ranging from 120 to 720 seconds. The delay is designed to avoid impacting the utility grid when multiple charging stations are in the same area attempting to resume charging simultaneously. EVoInnovate EVSE User Manual & Installation Guide www.evocharge.com...
• If the power cable or the charging connector is damaged, turn off the charging station supply circuit breaker, do not use the charging station, and please contact EVoCharge Customer Support for replacement parts. • When moving or lifting the unit, always grasp and carry by the charging station plastic body. Never attempt to lift, move, or carry the unit by any of the electrical cables.
Need help?
Do you have a question about the EVoInnovate EVO32-300-001 and is the answer not in the manual?
Questions and answers