Table of Contents
Related Manuals for 3D Platform WorkSeries 200 Series
Summary of Contents for 3D Platform WorkSeries 200 Series
- Page 1 3D Platform WorkSeries 200, 300 & 400 Manual Revision: B Date: December 28, 2017 WORKSERIES USER MANUAL 200, 300 & 400 Series 2017 ERSION ECEMBER 6402 East Rockton Road|Roscoe|Illinois|61073|USA 3dplatform.com • 3DP-DOC-005 (12-2017)
-
Page 2: Table Of Contents
Main Electrical Panel ............11 Care & Maintenance .............. 24 Initial Printer Setup ..............12 Maintenance (reference service schedule) ....... 24 Setup by 3D Platform Technician or Certified Service Cleaning the Nozzle ............24 Provider (CSP) ..............12 Safety Guidelines ............... 24 Gantry Setup .............. -
Page 3: Introduction
For support consequential, incidental, or other similar damages related questions, visit our support page at arising out of the use or misuse of this 3D Platform support.3dplatform.com. equipment. In no event shall the liability and/or obligations of 3D Platform arising out of the purchase of Disclaimers &... -
Page 4: Printer Specifications
3D Platform WorkSeries 200, 300 & 400 Manual Revision: C Date: December 28, 2017 Printer Specifications 3dplatform.com • 3DP-DOC-005 (12-2017) -
Page 5: Controls & Firmware
3D Platform WorkSeries 200, 300 & 400 Manual Revision: B Date: December 28, 2017 Controls & Firmware Sound Level • The level of airborne noise (acoustic pressure) Duet Wi-Fi controller standard (Ethernet option measured at the operator station is <70 dB(A). -
Page 6: Computer Setup & Software Installation
Workstation Requirements 3D Platform customers are: • Cura The 3D Platform WorkSeries 3D printer uses open Cura prepares your model for 3D printing. source controls. Computer/workstation requirements For novices, it makes it easy to get great are dependent on the software choice of the operator. -
Page 7: Facility Requirements
Refer to enclosure documentation for details. Optimal work environment Extreme heat, humidity, blowing vents, and/or fans can negatively affect the print quality of the 3D Platform WorkSeries 3D printers. The machine should be placed in a temperature controlled environment with an ambient operating temperature in the range of 15°C-... -
Page 8: Product Description
The 200, 300 and 400 Series are designed and The machines use open source controls and can be manufactured by 3D Platform to comply with CE operated using the touch screen control unit or web standards. The printer can use any open source material interface. -
Page 9: Safety
A hot surface is in the vicinity-do not touch. Print nozzle Print bed CRUSHING OF HANDS When in motion, the 3D Platform WorkSeries’ linear actuators that X axis move in multiple directions at variant speeds may be a pinch hazard Y axis (low risk due to force limitation). -
Page 10: Potential Hazard Zones
Date: December 28, 2017 Potential Hazard Zones The following areas represent potential hazardous zones on the 3D Platform WorkSeries 3D printers. Keep all persons and objects clear of these zones during use to avoid potential injury to the operator or damage to the machine. -
Page 11: Safety Guidelines & Warnings
Some materials may require ventilation. • Do not leave the 3D Platform WorkSeries 3D printer unattended while in operation. • The 3D Platform WorkSeries 3D printer includes linear actuators that move in multiple directions at variant speeds. -
Page 12: Main Electrical Panel
3D Platform WorkSeries 200, 300 & 400 Manual Revision: B Date: December 28, 2017 Main Electrical Panel The main electrical panel is in the top left storage drawer of the 200, 300 and 400 Series. Use extreme caution if accessing electrical panel. Electrical panel should only be accessed by an authorized, certified technician. -
Page 13: Initial Printer Setup
Initial Printer Setup Setup by 3D Platform Technician or Certified Service Provider (CSP) Most customers choose to have a 3D Platform factory technician or a CSP complete the initial setup and training. Please do not proceed with setup if this option was purchased. -
Page 14: Initial Actuator Alignment
Box. Ensure proper mating of the connectors and that the labels up. Racking of linear motion actuators can cause serious damage or breakage match upon installation. to mechanical hardware and/or brackets on the 3D Platform WorkSeries printer. 3dplatform.com • 3DP-DOC-005 (12-2017) -
Page 15: Powering Up
(network) connections list. c) Locate the power cord—stored within the 7. Select “Duet Wi-Fi” and connect. storage drawers of the 3D Platform WorkSeries—and attach to the cart unit. Note: If network does not appear, enter M552 S2 in Console d) Plug the power cord into the power outlet. -
Page 16: Connecting To The Web Interface
The red light indicates the sensor is operational. 1. After finishing Wi-Fi connection setup, navigate to If a sensor is non-operational, contact 3D Platform the “Console” tab on the touch screen. Support at support.3dplatform.com. Do not 2. Select the keyboard symbol at the top of the touch attempt to operate printer. -
Page 17: Home Sensor Verification Via Web Interface
Once initial setup is complete, machine must be calibrated prior to printing. If commissioning service has been purchased, 3D Platform or a CSP technician will perform initial machine calibration. Printing Process Workflow Source Files &... -
Page 18: Printer Operation
3D Platform WorkSeries 200, 300 & 400 Manual Revision: B Date: December 28, 2017 Printer Operation From the Touch Screen Heating the Extruders & Print Bed Active Temperature 1. On the touch screen, select the Standby button for From the Touch Screen EXT1. -
Page 19: Loading Filament
Insert filament into the top of the extruder. In the “MACROS” menu on the touch screen, select “load filament.” This will use the motor to pull the filament The 3D Platform WorkSeries 3D printer is equipped with into the extruder. dual filament sensors. This feature provides security during long prints. -
Page 20: Preparing The Print Bed
Repeat this process between prints to remove filament particles and other debris, as well as prepare the bed for the next print. Note: 3D Platform recommends using Aquanet unscented hairspray only. Any scented hairspray may contain oils and cause adherence issues on the print bed. -
Page 21: Starting A Print
Printing via SD Card 1. Adjusting Fan Speed a. Select “Print” menu on the touch screen. The 3D Platform WorkSeries 3D printer can be operated b. Select “Fan Speed.” independently with the Touch Screen Control Unit and c. Increase or decrease the fan speed to allow an SD Card. -
Page 22: Removing A Completed Print
3D Platform WorkSeries 200, 300 & 400 Manual Revision: B Date: December 28, 2017 Removing a Completed Print 1. When print completes, the machine will generally beep to notify the operator (settings dependent). 2. After print completes, bed and extruder will still be hot. -
Page 23: G-Codes/M-Codes
3D Platform WorkSeries 200, 300 & 400 Manual Revision: B Date: December 28, 2017 G-codes/M-codes A list of the G-Code/M-Code commands supported by our machine is listed on the support page at support.3dplatform.com. Additionally, the G-codes/M- Codes listed on reprap.org provide a complete list of all open source G-codes/M-codes commonly used in 3D printing. -
Page 24: 3D Printing Materials
Vendors & Manufacturers First Aid 3D Platform does not limit the filament able to be used on our printers. We do have some suppliers that we Follow instructions within a specific material’s Safety recommend and sell directly. These materials have been Data Sheet (SDS, formerly known as “MSDS”). -
Page 25: Care & Maintenance
When filament is not being extruded properly. For the safety of the user and to avoid shock or • When changing material type. unintended motion, all maintenance of the 3D Platform • Periodically between large prints—preventative WorkSeries 3D printer should be: maintenance. -
Page 26: Electrical Maintenance
Changing the Nozzle Electrical Maintenance (applies to Volcano extruders only) All electrical work should be assisted or performed by a 3D Platform service technician or a CSP. Contact Tools Required support.3dplatform.com. A wiring diagram can be • found on our website www.3dplatform.com. -
Page 27: Calibration & Test Prints
3D Platform WorkSeries 200, 300 & 400 Manual Revision: B Date: December 28, 2017 Calibration & Test Prints The files listed below are supplied with the printer on SD Card 0 (internal to control box) to assist in the set up and calibration process. -
Page 28: Babystepping
3D Platform WorkSeries 200, 300 & 400 Manual Revision: C Date: December 28, 2017 Nozzle is too close to print surface. Babystepping Babystepping is a function that allows the user to move (baby step) the Z axis during a print. This is especially useful when tweaking the first layer. -
Page 29: Contact Information
WorkSeries 200, 300 & 400 Manual Revision: B Date: December 28, 2017 Contact Information 3D Platform can be contacted through the following methods: Support Visit the website for literature and video documentation to quickly answer frequent questions regarding your equipment: support.3dplatform.com Sales &... -
Page 30: Appendix 1: Warranty Information
3D Platform offers a ninety (90) day limited warranty commencing on date of shipment for each machine bought through 3D Platform or an authorized 3D Platform reseller. An extended one (1) or two (2) year warranty is available for purchase. 3D Platform warrants that the 200, 300 and 400 WorkSeries shall conform to the description stated on the sale order and shall be free from defects in material or workmanship during the applicable warranty period when used under the normal conditions described in 3D Platform’s documentation found at www.3dplatform.com. -
Page 31: Appendix 2: Ce Conformance
Revision: C Date: December 28, 2017 Appendix 2: CE Conformance The below declaration states which directives the 3D Platform WorkSeries machines comply to. For a full test/compliance report, please contact 3D Platform. CE Declaration of Conformity Company Name: 3D PLATFORM Street Address: P.O. -
Page 32: Appendix 3: Touch Screen Operation
3D Platform WorkSeries 200, 300 & 400 Manual Revision: C Date: December 28, 2017 Appendix 3: Touch Screen Operation Main Menu Axis Movement Menu Printing Menu Paused Menu 3dplatform.com • 3DP-DOC-005 (12-2017) -
Page 33: Appendix 4: Replacement Parts
Use with Volcano Hot X1000-NZZL-120VOL Volcano 1.2 mm Nozzle Use with Volcano Hot X1000-0002 3D Platform Glass Bed Optional Use with Volcano Hot 1m X 1m Notes: Consumables are expected to show wear under normal usage of the machine. VOLCANO EXTRUDER REPLACEMENT PARTS... -
Page 34: Appendix 5: Service Schedule
3D Platform WorkSeries 200, 300 & 400 Manual Revision: C Date: December 28, 2017 Appendix 5: Service Schedule Weekly Service Items Mechanics Check bed with dial indicator Re-align actuators Clean and wipe IVT rails with 3-in-1 oil Check motor couplings, oil with 3-in-1 (to reduce noise) or tighten screws if needed... -
Page 35: Appendix 5: Revision Log
3D Platform WorkSeries 200, 300 & 400 Manual Revision: C Date: December 28, 2017 Appendix 5: Revision Log Revision Date Description of Change(s) June 2017 Initial Release November 2017 Added 400 Series Information December 2017 Updated CE Certification Contact 3dplatform.com • 3DP-DOC-005 (12-2017)
Need help?
Do you have a question about the WorkSeries 200 Series and is the answer not in the manual?
Questions and answers