3DP1000 outlined in this manual. The 3DP1000 is capable of carrying out the additive manufacturing process under open source controls, via 3D model output in the .gcode format. It can be operated using the USB computer interface or independently with the LCD control unit and SD card.
Safety SAFETY FEATURES SAFETY GUIDELINES & WARNINGS The 3DP1000 is designed to comply with CE standards. The following safety guidelines, as well as the instructions Standard printers, sold after 12/4/15 are equipped with within this user manual, ensure the safety of the user the following safety features: while operating and maintaining the 3DP1000 printer.
A hot surface is located in the vicinity—do not touch. • Print bed • X axis When in motion, the 3DP1000's linear actuators that move in CRUSHING OF HANDS • Y axis multiple directions at variant speeds may be a pinch hazard and cause injury.
Connectivity to Laptop: ELECTRICAL Standard AC Input: CONTROLS & FIRMWARE 220-250VRMS Print Bed and Printer Control Standard with the 3DP1000 printer: 15ARMS • Taurino (AT mega 2560) 60Hz or 50Hz • RAMPS 1.4 Sold with (1) NEMA L6-15 plug, see typical outlet diagram below.
Calibration Files UNPACKING THE PRINTER • The 3DP1000 printer will arrive in an industrial strength wood crate. Please take a moment to review the unpacking procedure to ensure the safety of the unpacker, as well as the printer. • A phillips head screw driver is required for uncrating the printer.
INSTALL SOFTWARE The 3DP1000 printer from 3D Platform utilizes open source controls, allowing users to utilize the software with which they are most comfortable. 3D Platform recommends the use of Simplify3D software. The links below provide easy access to this software program, as well as the configuration files that can be imported for ease of setup.
Note: Racking of linear motion actuators can cause serious damage or breakage to mechanical hardware and/or bracketry on the 3DP1000 printer. Follow the Initial Actuator Alignment process to reduce the risk of racking. Example of Racking – To Be Avoided...
Note: It is recommended to install the driver and 3D printing software PRIOR to connecting the printer to your computer. Launch your 3D printing software and connect to the 3DP1000. You may need to 'Refresh Ports' in order for your computer to initially find the printer. INSTALL FILAMENT SPOOL The filament spool holder is located on the back side of the printer.
Original Instructions 2015 Initial Setup HEAT THE EXTRUDER HEAT THE PRINT BED Preheat the extruder using your software and computer Set the print bed heat to 70° C. interface, or by using the LCD control unit. This is your initial bed temperature. °C Additional heat may be necessary Press the button on the LCD Screen,...
Work Environment WORKSTATION REQUIREMENTS Extreme heat, humidity, blowing vents, and/or fans can adversely affect the print quality of the 3DP1000. The The 3DP1000 utilizes open source controls. Computer/ printer should be located in a controlled temperature workstation requirements are dependent on the software environment with an ambient operating temperature in choice of the operator.
Original Instructions 2015 Source Files & Typical Workflow SOURCE FILES 3D models can be custom designed in CAD programs The 3DP1000 printer produces three dimensional objects such as SolidWorks, Auto CAD, or Google SketchUp. using the FFF—Fused Filament Fabrication—type of .stl...
Original Instructions 2015 Preparing Files for Use Before a 3D model can be printed on the 3DP1000 Link to video: 1-2-3D Printing printer, two things must be done. The CAD model must be converted to either an .stl or .obj file, and;...
Call a physician. 122° F (50° C). Keep material in sealed container or Notes to physician: Treat symptomatically. bag with moisture-absorbing desiccant. Link to Video: What Materials Can Print on a 3DP1000 www.3DPlatform.com | 13...
Original Instructions 2015 Operating the 3DP1000 LEVELING THE PRINT BED Tools Required • Metric Allen Wrench Why is Leveling Important? A level print bed is critical to or Hex Key Set overall print quality–especially for consistent first-layer adhesion. • If one section of the print bed is lower than another, the first layer might not adhere properly.
Original Instructions 2015 Operating the 3DP1000 HEAT THE PRINT BED The print bed on the 3DP1000 printer is heated to Link to bed heater control panel user provide better adhesion of your printed parts. Each instructions material you use will likely require a different bed temperature.
LCD CONTROL UNIT OPERATION Info Screen (continued) Control Opens Control menu Main Returns to Main menu The 3DP1000 can be operated independently using the Temperature Opens Temperature menu LCD Control Unit, located on the front of the machine. Control Returns to Main menu...
WITH COMPUTER • An alarm sounds until the filament is replaced and The 3DP1000 can be operated through the 3D printing the center button on the LCD Control Unit is pressed to resume the print. software's Manual or Machine Control Panel. Follow...
Care and Maintenance MAINTENANCE For the safety of the user and to avoid shock or SIMO® Series actuators from PBC Linear®: unintended motion, all maintenance of the 3DP1000 • Rail and bearing system is inclusive of internal 3D printer should be: lubrication system—requiring no preventative...
Original Instructions 2015 Care and Maintenance CLEANING THE NOZZLE Tools Required • 7 mm Wrench or Socket Wrench Use extreme caution when maintaining or operating • Crescent Wrench heated machinery. The nozzle must be heated to 180º C (minimum) when cleaning. When to clean the nozzle: CHANGING THE NOZZLE •...
Original Instructions 2015 Care and Maintenance WIRING DIAGRAM For the safety of the user and to avoid shock or unintended motion, all electrical maintenance of the 3DP1000 3D printer should be: • Conducted with the machine unplugged from all electrical outlets. •...
Original Instructions 2015 Calibration & Test Prints • The files listed below are supplied with the printer, on an SD card, in order to assist in the set up and calibration process. • Verify your print bed is level using the bed leveling file supplied (Bed-level-test.stl)—make adjustments the file prints.
Print Bed Temperature prevent clogging and promote smooth filament flow. The print bed on the 3DP1000 printer is heated to • Canola oil treatment: provide better adhesion of your printed parts. Each –...
Z-Offset in the software prior to slicing. • Each 3DP1000 printer is calibrated to a '0' Z-Offset at the manufacturing facility prior to shipment. However, if your first layer shows signs of the nozzle being too far or too close to the print bed—adjust the Z-Offset in the software prior to slicing.
Original Instructions 2015 Printing Tips GETTING A GOOD FIRST LAYER Link to article: Perfecting the First Layer The first layer may be the most important layer of any print—and perhaps the most difficult. A good first layer is vital to the success of your print. First layer height too high Qualities of a good first layer include: •...
This online tool provides instant viewing of 2D and 3D Please visit the following links for Slicer and Simplify 3D designs—without purchasing software. software tutorials. Note: these tutorials are not produced by 3D Platform, but are recommended. https://360.autodesk.com/Viewer • Simplify 3D https://www.youtube.com/watch?v=D968RL1Z6l4...
Original Instructions 2015 Replacement Parts PART NUMBER DESCRIPTION X1000-NZZL030 0.3 mm Nozzle X1000-NZZL035 0.35 mm Nozzle X1000-NZZL040 0.4 mm Nozzle X1000-NZZL060 0.6 mm Nozzle X1000-NZZL080 0.8 mm Nozzle 1.2 mm Nozzle X1000-0008 Fan: PLA/Material Unit X1000-ASY-0002 Extruder Assembly Complete - BULLDOG X1000-0015 Upper Glass Bracket - 3D Printed 3DP Heated Pad, 1 meter x 1 meter,...
Q: Can I use filament from any manufacturer? A: Yes! The 3DP1000 is designed to accommodate filament from multiple manufacturers – as long as it is 3 mm in size. Please visit our website at www.3DPlatform.com...
Any obligations of seller pursuant to this agreement or the failure of the goods to perform in any particular manner. • In no event shall the liability and/or obligations of 3D Platform arising out of the purchase of equipment by you or others exceed the purchase price of the 3DP1000 3D printer.
ACC - Services Contact 105 route des pommiers Centre Ubidoca 74370 St Martin Bellevue France 3D PLATFORM declares under our sole responsibility that the equipment described as: Equipment Name: 3D Printer Generic Equipment Description: FFF 3D Printer Model /Type: 3DP 1000 Serial number(s): Complies with the requirements of the following European Directives: •...