Table of Contents
Advertisement
Quick Links
NOTES
- 20 -
OI-UT003DL
TABLE OF CONTENTS
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.0 TI-007DL Features & Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.0 Measurement Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 S-232 Port
5.0 RS-232 Serial Port & Data Logger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3 Clearing A Storage Location
5.4 Clearing An Entire File
5.5 Clearing All Files
5.6 Sending Files To A Computer
5.7 Printing Files
6.0 Transducer Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.0 Appendix A: Product Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.0 Appendix B: Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.0 Appendix C: Sound Velocities Of Common Materials . . . . . . . . . . . . . . .
10.0 Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- 1 -
2
8
9
11
15
16
17
18
19
Advertisement
Table of Contents
Related Manuals for ELECTROMATIC TI-007DL
Summary of Contents for ELECTROMATIC TI-007DL
-
Page 1: Table Of Contents
3.0 TI-007DL Features & Modes ........ -
Page 2: Introduction
The Electromatic Model TI-007DL is a precision Ultrasonic Micrometer. Based on ELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the original the same operating principles as sonar, the TI-007DL is capable of measuring the purchaser that this product is of merchantable quality and confirms in kind and quality thickness of various materials with accuracy as high as ±... -
Page 3: Operation
2184 The Keypad Brass 0.173 4394 This key is used to turn the TI-007DL on and off. When the TI-007DL is Cadmium 0.109 2769 turned ON, it will first perform a brief display test by illuminating all of the Cast Iron 0.180 (approx.) -
Page 4: The Display
CLR keys (hi-lighted in green). The combination of these keys control the Measuring tubing data logging features of the TI-007DL. Refer to the data logging section on page 11. When measuring a piece of tubing for wall thickness, it may prove beneficial to have multiple delay lines with different radiuses for different tubing diameters. -
Page 5: The Transducer
The Stability Indicator should have six or seven bars darkened, and a number should appear in the display. If the TI-007DL has been set to the correct sound velocity (see page 6), the number in the display will indicate the actual thickness of the material directly beneath the transducer. -
Page 6: Condition And Preparation Of Surfaces
Calibration delay line. Measuring on a curved surface, may require the use of a transducer with a In order for the TI-007DL to make accurate measurements, it must be set to the correct matching curved wearface. sound-velocity for the material being measured. Different types of material have different inherent sound-velocities. - Page 7 The TI-007DL is now displaying the sound velocity value it has calculated based on the thickness value that was entered in step 6. 8. Press the CAL key once more to exit the calibration mode. The TI-007DL is now ready to perform measurements.
-
Page 8: The Back Light
Alarm Mode The procedure for printing a file is outlined below: The Alarm Mode feature of the TI-007DL allows the user to set an audible and visual 1. Refer to the section on Connecting to a Computer, page 11, before proceeding. - Page 9 Alarm Mode 1. Press the ON/OFF key to power up the TI-007DL Note: The display will flash the current storage location (L007, L039, etc ), followed by the status of the location. The storage location can contain one of 2.
-
Page 10: Measurement Modes
1. Connect the accessory cable (part# N-306-0010) to the 2 pin jack located on the modes according to the different materials being measured. The following section out- bottom of the TI-007DL, and the 9 pin connector to a serial port on the computer. lines how to switch between measurement modes: 2. - Page 11 CHECK LINE ® • BY ELECTROMATIC TI-007DL ODEL ULTRASONIC MICROMETER Distributed by: ABQ Industrial LP USA OPERATING INSTRUCTIONS Tel: +1 (281) 516-9292 / (888) 275-5772 eFax: +1 (866) 234-0451 Web: https://www.abqindustrial.net E-mail: info@abqindustrial.net...
Need help?
Do you have a question about the TI-007DL and is the answer not in the manual?
Questions and answers