Page 1
Table of Contents Index Operator Manual 3P1006NT Semi-Mounted 10-Foot No-Till Drill Manufacturing, Inc. www.greatplainsmfg.com Read the operation manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! 28213 Illustrations may show optional equipment not supplied with standard unit.
Page 2
Machine Identification Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new manual. If you or the dealer have added options not originally ordered with the machine, or removed options that were originally ordered, the weights and measurements are no longer accurate for your machine.
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Page 4
Table of Contents Index Table of Contents Index...
3P1006NT Table of Contents Index Important Safety Information Look for Safety Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it.
Page 6
3P1006NT Table of Contents Index Important Safety Information Wear Protective Equipment Wear protective clothing and equipment. Wear clothing and equipment appropriate for the job. Avoid loose-fitting clothing. Because prolonged exposure to loud noise can cause hearing impairment or hearing loss, wear suitable hearing protection such as earmuffs or earplugs.
Page 7
3P1006NT Table of Contents Index Important Safety Information Use Safety Lights and Devices Slow-moving tractors and towed implements can create a hazard when driven on public roads. They are difficult to see, especially at night. Use flashing warning lights and turn signals whenever driving on public roads.
Page 8
3P1006NT Table of Contents Index Important Safety Information Practice Safe Maintenance Understand procedure before doing work. Use proper tools and equipment. Refer to this manual. Work in a clean, dry area. Lower the drill, put tractor in park, turn off engine, and remove key before performing maintenance.
Keep all safety decals clean and legible. Replace all damaged or missing decals. Order new decals from your Great Plains dealer. Refer to this section for proper decal placement. When ordering new parts or components, also request corresponding safety decals.
Page 10
3P1006NT Table of Contents Index Important Safety Information Reflectors: Daytime 32686A 838-267C On rear face of lift assist cross tube, inside red reflectors; On rear face of walkboard, inside red reflectors; 4 total See “Transporting” on page 26. 32686B Reflectors: Amber...
Page 11
3P1006NT Table of Contents Index Important Safety Information Danger: Moving Chain (Option) 32760 818-518C CAUTION MOVING CHAIN HAZARD To prevent serious injury from moving chain: DO NOT operate with enclosure missing 818-518C REV. B Native Grass: On outside of box end wall, under both covers;...
Page 12
3P1006NT Table of Contents Index Important Safety Information Warning: Speed 818-337C WARNING EXCESSIVE SPEED HAZARD To Prevent Serious Injury or Death: Do NOT exceed 20 mph maximum transport speed. Loss of vehicle control and/or machine damage can result. 818-337C Rev. B On front face of lower front cross tube inside 3-point hitch;...
Page 13
3P1006NT Table of Contents Index Important Safety Information Warning: Hand Crush 838-611C 32760 On axle tube; 2 on axle tube 2, 3, 4, or 5 total Warning: Hand Crush (Option) 32763 838-611C Dual Seed: Under lid; 1 Under Lid 2, 3, 4, or 5 total See “Hitching Tractor to Drill”...
Page 14
3P1006NT Table of Contents Index Important Safety Information Caution: Tires Not A Step 818-398C On outside face of caster arms above tires; 68632 2 total See “Tires Not a Step” on page 3. Caution: General 818-719C CAUTION To prevent injury or death: Read and understand Operator’s Manual before using.
Page 15
3P1006NT Table of Contents Index Important Safety Information NOTICE: Petroleum Products 858-679C On left-hand ends of seed boxes; 28214 1 per seed box 2018-06-06 Table of Contents Index 151-144M...
3P1006NT Table of Contents Index Introduction Great Plains welcomes you to its growing family of new product owners. Your Semi-Mounted 10-Foot No-Till Drill has been designed with care and built by skilled workers using quality materials. Proper setup, maintenance, and safe operating practices will help you get years of satisfactory use from the machine.
Refer to Figure 2 Your machine’s parts were specially designed and should only be replaced with Great Plains parts. Always use the serial and model number when ordering parts from your Great Plains dealer. The serial-number plate is located on the top front cross-tube, left of the left gauge wheel mount.
3P1006NT Table of Contents Index Preparation and Setup This section helps you prepare your tractor and drill for use. Pre-Delivery Setup If the drill has just been delivered, or has been broken down for re-shipment, this item needs to be completed prior to first field use: •...
Extension: Hitch to the tractor FIRST. Extension: Unhitch at the drill FIRST. Equipment Damage Risk: Great Plains CPH, PFH or SSH accessory hitches are not compatible with the 3P1006NT. The Great Plains extension hitch is compatible with most standard quick hitches.
Check all hydraulic lines and fittings before applying pressure. Fluid escaping from a very small hole can The hydraulic system of the 3P1006NT drill has one be almost invisible. Use paper or cardboard, not body parts, single-acting lift-assist cylinder. (This cylinder has a and wear heavy gloves to check for suspected leaks.
3P1006NT Table of Contents Index Preparation and Setup Leveling the Drill Perform leveling in representative field conditions. On hard ground or pavement, coulters and openers may prevent determination of drill level. 1. If caster swivel locks were engaged, retract the rods and pin them up.
Page 22
3P1006NT Table of Contents Index Preparation and Setup (Applies to drills with serial numbers A1059W+ Check Level For serial number A1058W-, see page 19.) 2. Lower drill until the cylinders rest on the stroke The height of the drill at rear (when lowered) is adjusted control spacers.
Page 23
3P1006NT Table of Contents Index Preparation and Setup Stroke Control Spacers (s/n A1058W-) Check Level (Applies to drills with serial numbers A1058W- 2. Lower drill until the cylinders rest on the stroke For serial number A1059W+, see page 17.) control spacers. See “Drill Lift/Lower (s/n A1058W- )”...
3P1006NT Table of Contents Index Operating Instructions This section covers general operating procedures. Experience, machine familiarity and the following information will lead to efficient operation and good working habits. Always operate farm machinery with safety in mind. Pre-Start Checklist High Pressure Fluid Hazard: Escaping fluid under pressure can have sufficient pressure to penetrate the skin.
3P1006NT Table of Contents Index Operating Instructions Drill Lift/Lower (s/n A1059W+) (applies to drills with serial numbers A1059W+ For serial number A1058W-, see page 22) Raising and lowering the drill relies on the tractor 3-point lift arms in front, and hydraulic lift-assist cylinder at rear.
3P1006NT Table of Contents Index Operating Instructions Drill Lift/Lower (s/n A1058W-) (applies to drills with serial numbers A1058W- for serial number A1059W+, see page 21) Raising and lowering the drill relies on the tractor 3-point lift arms in front, and hydraulic lift-assist cylinders at rear.
3P1006NT Table of Contents Index Operating Instructions Lowering The lift-assist cylinder(s) is(are) single-acting. Move the tractor remote circuit lever to Retract. The drill to settles by gravity. The cylinder piston drives oil back to the tractor reservoir. Do not use Float to lower, or the drill will settle suddenly.
3P1006NT Table of Contents Index Operating Instructions Caster Pivot Locks (s/n A1059W+) (applies to drills with serial numbers A1059W+ for serial number A1058W-, see page 25) To prevent side movement of the drill when transported by trailer, the lift-assist casters may be locked in their full-reversing orientation.
3P1006NT Table of Contents Index Operating Instructions Caster Pivot Locks (s/n A1058W-) (applies to drills with serial numbers A1058W- for serial number A1059W+, see page 24) To prevent side movement of the drill when transported by trailer, the lift-assist casters may be locked in their full-trailing or full-reversing orientations.
3P1006NT Table of Contents Index Operating Instructions Transporting WARNING Instructions and advisories for transport depend on the EXCESSIVE SPEED method of transport. Towing behind a tractor is covered HAZARD on this page under “Semi-Mounted 3-Point Transport”. To Prevent Serious Injury or Death: Do NOT exceed 20 mph maximum Transport via trailer is covered under “Trailer Transport”...
6. Carefully tow drill from trailer. 7. Remove caster pivot swivel locks (if engaged, page 24). Great Plains recommends locking casters prior to loading for trailer transport, and leaving them locked for transport and 8. Unless arriving at planting ground, install lift-assist unloading.
3P1006NT Table of Contents Index Operating Instructions Loading Materials Fully loaded with dense seed and fertilizer, the drill weighs an additional 1970 lbs (894 kg). Include this weight when checking tractor capability. The drill must be hitched for seed loading.
Rate setting controls are different for each box, but All chart rates, for all boxes, are approximate. independent for each box. Some boxes have more than Great Plains strongly recommends calibration of each one control. box to the material to be applied.
3P1006NT Table of Contents Index Operating Instructions Acremeter Operation The acremeter counts shaft rotations whenever the shaft is rotating - normally this is only with the drill lowered and in motion. The meter is programmed to display rotations as acres or hectares, when using all rows, factory-specified tires and tire inflations.
3P1006NT Table of Contents Index Operating Instructions Field Operation 1. Hitch drill to a suitable tractor (page 15). Crushing Hazard: Semi-mounted implements with rear lift-assist wheels You may be severely injured or killed by being crushed maneuver differently in field and highway transport, compared between the tractor and drill.
Right Drive Type gearbox lever provide adjustments for optimal field results. • Seed Rate Handle at box (drill rear) The 3P1006NT has double-disc 06 Series openers with • depth-controlling press wheels mounted on floating Feed Cup Door (one each seed tube) opener frames.
3P1006NT Table of Contents Index Adjustments Coulter Adjustments Refer to Figure 19 A no-till coulter , is mounted directly ahead of each opener on the drill. The coulters cut through heavy trash and make a groove in the soil for the openers. The coulters are mounted on the drill frame so coulter cutting depth changes as the drill is raised and lowered.
Drill w/Small Seed 178 lbs (81 kg) 256 lbs (116 kg) 3P1006NT configurations typically are too light to reach Fert. & Small Seed 200 lbs (91 kg) 278 lbs (126 kg) the factory down-force of 400 lbs at all rows. The table at NG &...
3P1006NT Table of Contents Index Adjustments Coulter Depth (Individual Rows) running depth coulters adjusted simultaneously by changing the tool bar height. Adjusting the height of a small number of coulters may be useful for rows in tire tracks. Adjust individual coulters as follows.
3P1006NT drill; coulter is not part of opener assembly and is not shown) From front to back, a Great Plains 06 Series row unit can include the following capabilities (some optional): 1. Disc Blades: standard, 2 per row unit Double disc blades open a furrow, creating the seed bed.
3P1006NT Table of Contents Index Adjustments Disc Blade Adjustments Opener disc angle and stagger is not adjustable, but disc-to-disc spacing is, and may need attention as discs experience normal wear. Spacers must be reset when blades are replaced. Refer to Figure 25 The ideal spacing causes the blades to be in contact for about one inch.
3P1006NT Table of Contents Index Adjustments Opener Adjustments “W” Opener Down Pressure Opener springs provide the down pressure necessary for opener discs to open a seed trench. The springs allow the openers to float down into depressions and up over obstructions.
3P1006NT Table of Contents Index Adjustments Small Seeds Tube Adjustment (Option) Refer to Figure 29 On a drill with the Small Seeds option, deeper seed placement may be achieved by rotating the seed tube to face forward. This orientation is suggested only if the seed firmer is a ®...
3P1006NT Table of Contents Index Adjustments Opener Depth (Press Wheel Height) A press wheel attached to each opener body controls seeding depth. To maintain consistent depth, the relationship between the bottom of the opener discs and press wheel is fixed upwardly by an adjustable stop on each opener.
3P1006NT Table of Contents Index Troubleshooting Problem Cause Solution Excessive field speed. Reduce field speed. Uneven seed spacing or uneven stand Feed cups plugging. Clean out feed cups. Seed tubes plugging. Clean out seed tubes. See “Opener discs not turning freely” in this Opener discs not turning freely.
Page 46
3P1006NT Table of Contents Index Troubleshooting Problem Cause Solution Some boxes do not have same number of Boxes not emptying evenly Load more material than required. Re-distribute feed cups between each divider of when re-loading. bulkhead. Main box seed cup door setting Set all doors the same, per seed size.
5. Inspect hydraulic hoses for cuts, cracks and aging. Check fittings for evidence of leaks. 6. Replace any worn, damaged or illegible safety decals. Order new decals from your Great Plains dealer. See “Safety Decals” on page 5. 2018-06-06 Table of Contents...
3P1006NT Table of Contents Index Maintenance and Lubrication Caster Brake Adjustment Caster Brake Adjustment (s/n A1059W+) (applies to drills with serial numbers A1059W+ For serial number A1058W-, see page 45) Refer to Figure 32 The rear lift-assist wheels each have independent adjusters for the caster pivot.
3P1006NT Table of Contents Index Maintenance and Lubrication Caster Brake Adjustment (s/n A1058W-) (applies to drills with serial numbers A1058W- for serial number A1059W+, see page 44) Refer to Figure 34 The rear lift-assist wheels each have independent adjusters for the caster pivot. The adjustments will vary depending on different field-to-field conditions as well as road transport conditions.
3P1006NT Table of Contents Index Maintenance and Lubrication Materials Clean-Out Main Box and Dual Box Clean-Out Refer to Figure 36, which depicts the seed cup door handle in a normal operating position. 1. Set the Seed Rate Handle to zero (0). This moves the seed cup sprockets out of the seed path.
3P1006NT Table of Contents Index Maintenance and Lubrication Fertilizer Box Clean-Out After applying fertilizer, clean the box as soon as possible. Fertilizers often contain corrosive chemicals. Refer to Figure 38 With a small scoop or can, remove as much fertilizer as possible from drill boxes.
3P1006NT Table of Contents Index Maintenance and Lubrication Chain Maintenance Initially check the drive chains after the first 10 hours of drill use. The slack of new chains tends to increase during the first few hours of operation due to seating.
3P1006NT Table of Contents Index Maintenance and Lubrication Older Drill Model Flap Refer to Figure 43 To replace a seed flap use a needle nose or similar tool and squeeze the tabs together. Pull plastic seed flap down out of metal bracket...
Page 54
3P1006NT Table of Contents Index Maintenance and Lubrication Eye bolt Adjustment (s/n A1058W-) (applies to drills with serial numbers A1058W- For serial number A1059W+, see page 49) Refer to Figure 45 It may occasionally be necessary to make adjustments to...
3P1006NT Table of Contents Index Maintenance and Lubrication Bleeding Hydraulics Bleeding Hydraulics (s/n A1059W+) (applies to drills with serial numbers A1059W+ For serial number A1058W-, see page 52) High Pressure Fluid Hazard: Escaping fluid under pressure can have sufficient pressure to penetrate the skin.
Page 56
3P1006NT Table of Contents Index Maintenance and Lubrication Bleeding Hydraulics (s/n A1058W-) (applies to drills with serial numbers A1058W- For serial number A1059W+, see page 51) High Pressure Fluid Hazard: Escaping fluid under pressure can have sufficient pressure to penetrate the skin. Check all hydraulic lines and fittings before applying pressure.
3P1006NT Table of Contents Index Maintenance and Lubrication Lubrication and Scheduled Maintenance Intervals (operating hours) Multi-purpose Multi-purpose Multi-purpose Inspection at which service oil lubricant spray lubricant grease lubricant is required 34208 Coulter Arm Pivots One pivot per row; 15 total (via grease bank)
Page 58
3P1006NT Table of Contents Index Maintenance and Lubrication Caster Pivots (s/n A1059W+) One zerk each pivot; 2 total Type of Lubrication: Grease Quantity = Until grease emerges 32061 Caster Pivots (s/n A1058W-) One zerk each pivot; 2 total Type of Lubrication: Grease...
Page 59
3P1006NT Table of Contents Index Maintenance and Lubrication Small Seeds Shaft Bearings (Option) 1 zerk total Type of Lubrication: Grease Quantity: Until grease emerges 18082 Felt Barrier Seals 16381 1 seal at each shaft end, 2 total Type of Lubrication: Oil Quantity: Soak seal ...
Page 60
3P1006NT Table of Contents Index Maintenance and Lubrication Drive Chains Required See “Chain Routing” starting on page 66 for locations all chains by drill configuration. 12227 Type of Lubrication: Chain Lube Quantity = Coat thoroughly. Coulter Hub Bearings Seasonal One zerk per coulter; 15 total...
Page 61
3P1006NT Table of Contents Index Maintenance and Lubrication Caster Wheel Bearings (s/n A1059W+) Seasonal 2 races total Type of Lubrication: Grease Quantity = repack 32531 Caster Wheel Bearings (s/n A1058W-) Seasonal 2 races per wheel; 4 total Type of Lubrication: Grease...
3P1006NT AGITATOR KIT W/DRIVE 118-970A 3P1006NT AGITATOR KIT W/O DRIVE 118-971A Coulter Blades The standard coulter blades on the 3P1006NT drill are 17 in. (43.2 cm) 820-156C Turbo or 820-018C Fluted. Available replacement and alternate blades include: Description Part Number...
Page 63
3P1006NT Table of Contents Index Options Dual Seed Box This seed box is an optional second seed box installed behind the main seed box used for planting a wide variety of seeds. It is used for planting the same or additional crops as the main seed box.
Page 64
The base drill includes a choice of press wheels. Additional wheels are available, and all may be field-installed. This manual does not list kit part numbers as the available wheels are often region-specific. Consult your Great Plains dealer. 32617 32620 32621 Series II Native Grass Attachment This attachment is designed to seed fluffy, hard-to-plant grasses.
Page 65
3P1006NT Table of Contents Index Options Seed Firmers The standard 3P1006NT drill includes seed flaps. Only one type of optional seed firmer may be installed at the same time. Order one firmer kit per opener. ® Seed-Lok Seed Firmer Description Part Number ®...
Page 66
3P1006NT Table of Contents Index Options Seed Tube Plug (Small Seeds) This plug stops seed flow from the small seeds box above the meter. Order one per row to set inactive. Description Part Number SML SDS CUP PLUG 133-315H 27407...
Page 67
3P1006NT Table of Contents Index Options Weight Brackets The weight brackets are available to add weight for additional penetration in no-till conditions. The kit includes two weight brackets , two weight bracket adjustment legs , and mounting hardware. Also included are two decal mounts...
3P1006NT Table of Contents Index Appendix A - Reference Information Specifications and Capacities 3P1006NT Row Spacing 7.5 in. (19.1 cm) Rows per drill Swath 112.5 in. (285.8 cm) Weight, pounds 4820-6388 lbs. (2187-2898 kg) Transport Width approx. 118.25 in. (3.00 m) Height approx.
3P1006NT Table of Contents Index Appendix A - Reference Information Torque Values Chart Bolt Head Identification Bolt Head Identification Bolt Bolt 10.9 Size Size Grade 2 Grade 5 Grade 8 Class 5.8 Class 8.8 Class 10.9 ft-lb ft-lb ft-lb ft-lb...
3P1006NT Table of Contents Index Appendix A - Reference Information Chain Routing Striped arrows show chain direction. “T” Callouts show tooth counts for sprockets other than idler sprockets. “i” Callouts show tooth counts for idler sprockets. “P” Callout show chain pitch count.
Page 71
3P1006NT Table of Contents Index Appendix A - Reference Information Left Gearbox to Main Seed Box Meters See “Standard (Left) Ground Drive to Gearbox” on page 66 for gearbox input. Main box meters are the only meters coupled to the left gearbox output.
Page 72
3P1006NT Table of Contents Index Appendix A - Reference Information Native Grass (Right) Ground Drive (Option) See “Right Gearbox to Native Grass Meters (Option)” on page 69 for Native Grass gearbox output. One sprocket from storage tower is mounted at Native Grass meter shaft (the 17T as shipped).
Page 73
3P1006NT Table of Contents Index Appendix A - Reference Information Right Gearbox to Native Grass Meters (Option) See “Native Grass (Right) Ground Drive (Option)” on page 68 for Native Grass gearbox input. Native Grass Driven Sprocket: 14T through 23T from storage tower...
Page 74
3P1006NT Table of Contents Index Appendix A - Reference Information Main Seed Box Agitator (Option) No Fertilizer or Small Seeds installed. 28301 Agitator and Fertilizer Drive (Options) No Small Seeds installed. See “Fertilizer Box Drive (Option)” on page 72 for Fertilizer Box drive.
Page 75
3P1006NT Table of Contents Index Appendix A - Reference Information Agitator and Small Seeds Drive (Options) No Fertilizer or Native Grass installed. See “Agitator and Small Seeds Drive w/Native Grass (Options)” on page 71 for Native Grass configuration. See “Small Seeds Box Drive (Option)”...
Page 76
3P1006NT Table of Contents Index Appendix A - Reference Information Fertilizer Drive (Option) No Main Seed Box Agitator installed. See “Fertilizer Box Drive (Option)” on page 72 for Fertilizer Box drive. 28302 Fertilizer Box Drive (Option) See “Small Seeds Box Drive with Fertilizer (Option)”...
Page 77
3P1006NT Table of Contents Index Appendix A - Reference Information Fertilizer Box Drive with Small Seeds (Options) See “Fertilizer Box Drive (Option)” on page 72 for Fertilizer Box drive details. See “Small Seeds Box Drive (Option)” on page 74 for Small Seeds Box drive details.
Page 78
3P1006NT Table of Contents Index Appendix A - Reference Information Small Seeds Drive w/Native Grass (Options) Fertilizer installed. See “Small Seeds Drive (Option)” on page 73 if Native Grass not installed. See “Small Seeds Box Drive (Option)” on page 74 for Small Seeds Box drive.
Page 79
3P1006NT Table of Contents Index Appendix A - Reference Information Small Seeds Box Drive with Fertilizer (Option) When Fertilizer is also installed, Small Seeds Jackshaft is driven from Fertilizer jackshaft. If Fertilizer is not also installed, see “Small Seeds Box Drive (Option)” on page 74.
Page 80
3P1006NT Table of Contents Index Appendix A - Reference Information Dual Seed Drive (Option) Dual box meters are driven by the right-hand gearbox. 31627 2018-06-06 Table of Contents Index 151-144M...
Page 81
3P1006NT Table of Contents Index Appendix A - Reference Information Dual Seed and Small Seeds Drive (Options) Dual box meters are driven by the right-hand gearbox. 31628 2018-06-06 Table of Contents Index 151-144M...
3P1006NT Table of Contents Index Appendix A - Reference Information Hydraulic Diagrams Lift-Assist: s/n A1059W+ 32056 Null4: Lift-Assist: s/n A1058W- 28224 2018-06-06 Table of Contents Index 151-144M...
27-43 37-58 ORB straight Unload Truck The 3P1006NT drill is delivered by flatbed truck. When coordinating the unload with the Great Plains driver, plan to position the partially assembled drill at a spot with: • at least 10 ft. (3 m) clearance behind the press wheels, •...
Page 84
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Install Lift-Assist Install Wheels Refer to Figure 49 Use the caster pivot locks as needed to prevent caster swiveling. The pivot arm is shown hoisted. The work can be performed with the arm resting on the ground.
Page 85
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Install Pivot Refer to Figure 53 15. Select the pivot mount: LIFT ASSIST REAR PVT MNT 151-171H and one: 151-381D LIFT ASSIST AXLE PIVOT PIN and two: 161-056D CASTER SPACER 16. Orient the pivot mount...
Page 86
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Caster Shaft Installation Refer to Figure 54 and Figure 55 Begin Install Shaft 21. Select one each: 161-116D LIFT ASSIST CASTER SHAFT 802-060C HHCS 5/8-11X4 GR5 803-024C NUT LOCK 5/8-11 PLT...
Page 87
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Attach Lift-Assist Frame Mount Refer to Figure 56 Frame Mount Weldment 27. Select one each: 151-179H LIFT ASSIST FRAME MNT WLDMNT Select eight each bolts, washers, nuts: 802-053C HHCS 5/8-11X1 3/4 GR5...
Page 88
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Connect Parallel Arms Refer to Figure 57 and Figure 58 Lower Parallel Arm 31. Select one: 151-173H LIFT ASSIST LWR PARALLEL ARM The lower parallel arms have a cross-tube with a cylinder lug .
Page 89
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Hydraulic Setup Refer to Figure 59 38. Select one each: 811-065C EL 9/16MJIC 9/16MORB 841-286C HH1/4R2 134 9/16FJIC 1/2MNPT 39. Secure the FJIC end of hose to the end port of the elbow .
Page 90
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Lift-Assist Closeout Refer to Figure 61 46. Locate one sets of stroke control spacers: 810-242C STROKE CONTROL SPACERS 1 1/8 If they are in the main seed box, relocate the set to the rod on the weldment.
Page 91
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Red Lights Refer to Figure 63 1. Select two: 833-696C LIGHT, RED LAMP - LED Select four: 801-081C SCREW HEX SELF TAP 1/4-20X3/4 2. Install the two red lights to the mount...
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Attach Meter Hoses at Rows All meter hoses are shipped disconnected at the row units. Clamps are shipped inside a seed box. The opener frame has openings for up to three material hoses: •...
Page 93
3P1006NT Table of Contents Index Appendix B - Pre-Delivery Install SMV Reflector Refer to Figure 66 The SMV reflector is shipped pre-assembled to the mount , but dismounted from the pivot . Locate it in a seed box or crate.
3P1006NT Table of Contents Index Appendix C - Accessory Installation Carbide Disc Scraper Installation Optional carbide disc scrapers are not factory installed. See page 58 for ordering. This page cover installation of: 121-781A SPRING SCRAPER ASSEMBLY Start with row 1 (left-most row unit): 1.
3P1006NT Table of Contents Index Appendix C - Accessory Installation Weight Bracket Installation These instructions apply to an installation of an optional 151-135A weight bracket kit. Refer to Figure 68 Start at the left side of the drill. 1. Select one:...
Page 96
This Warranty is limited to the replacement of any defective part by Great Plains and the installation by the dealer of any such replacement part. Great Plains reserves the right to inspect any equipment or part which are claimed to have been defective in material or workmanship.
Need help?
Do you have a question about the 3P1006NT and is the answer not in the manual?
Questions and answers