Unfolding The Stroller; Installing The Front Wheels - Joovy ScooterX2 807X Manual

2 Unfolding the Stroller

• Keep children away from stroller while unfolding.
• Orient the stroller with the handlebar facing upward and closest to you.
• If necessary, release the folding lock located on the right side by lifting the lock off of the extended rivet. See Figure 2.1.
• Pull upwards on the handlebar until the stroller is completely opened and the latching mechanism on each side is engaged. See Figure
2.2. Be careful not to scratch the floor when opening the stroller.
• Visually check and gently push downward on the handlebar to ensure that the stroller is completely opened and locked before ANY use of
the product.
CAUTION: While unfolding the stroller, be careful to keep your fingers from being pinched by moving parts.
3 Installing the Rear Wheel Axle and Brake Set and Rear Wheels
• In a clean, dry place rest the stroller upside down with the rear legs facing upwards.
• Locate the rear axle and brake set and slide it onto the rear legs with the link brake facing the rear of the stroller. Be sure to slide each
side all the way on until the push pins are engaged in the holes of the plastic.
NOTE: You may need to push each of the push pins in to slide the plastic into place. See Figure 3.1.
• Pull upward on each side of the rear axle to ensure it is installed properly.
• Push the bar linking the brake levers into the disengaged position. See Figure 3.2.
To Install a Rear Wheel
• Locate a small washer and slide the washer onto the axle.
• Next place a rear wheel onto the axle over the small washer.
NOTE: The brake teeth on the wheel should be facing inward toward the brake lever.
• Then place one large washer onto the axle over the wheel.
• Next slide a spring washer onto the axle.
• Take another large washer and slide it onto the axle.
• Push the washers in to expose the axle hole. Then take one snap pin and insert the straight leg into the
small hole in the axle. Push it firmly into this hole until the round portion of the other leg snaps completely
around the outside of the axle.
NOTE: The snap pin is curved (concave) to make insertion easier.
• Repeat the SAME installation sequence of washers, wheel, and snap pin for the remaining wheel.
• Install a hubcap onto each wheel by aligning the 5 tabs on the hubcap with the 5 slots in the wheel, and
then pushing it into place. Ensure that ALL 5 snaps have engaged securely and the hubcap cannot be
pulled off.
4 Rear Wheel Brakes
• The ScooterX2 comes equipped with a linked rear wheel brake system.
• To engage the rear wheel brakes, push down on one of the brake levers or the bar that connects the levers. See Figure 4.1. The stroller
may require slight forward or rearward movement in order to line up the teeth on the brake with each wheel brake cluster.
• Check that the brakes are properly applied by attempting to push the stroller backwards and forwards.
• To release the brakes, gently lift up on one of the brake levers or the bar that connects the levers. See Figure 4.2.
Always make sure the wheel brakes are engaged when the stroller is not being pushed so that the stroller will not roll
away. Never leave stroller unattended, especially on a hill or incline, as the stroller may tip over or slide.

5 Installing the Front Wheels

• Position the stroller so it is resting on the rear wheels and the handlebar. Locate one front wheel set and position the wheel set with the
swivel lock tab facing upward. Insert it onto a post located at the bottom front on one side of the stroller until an audible click is heard. See
Figure 5.1.
• Pull outward on the wheel set to ensure the wheel set is installed properly.
• Repeat this procedure for the other wheel.
• To remove a front wheel set, pull the metal ring at the bottom of the front wheel housing and slide the wheel set off of the post. See Figure
5.2.
!
ALWAYS keep children away from the stroller when unfolding.
Possible pinching hazard – Be careful when unfolding the stroller.
!
WARNING
WARNING
EN FR ES
REAR WHEEL SEQUENCE
1
Small Washer
2
Rear Wheel
3
Large Washer
4
Spring Washer
5
Large Washer
6
Snap Pin