Operating Devices; Adjusting The Settings; Working With Modes - Marantz RC3200/A Service Manual

4-2
TROUBLESHOOTING
- Changing the LCD Contrast
To adjust the LCD contrast on the touch screen:
1 Press and hold the Backlight button.
The screen lights up.
2 While still holding the Backlight button, press the Page Up button once
to increase the LCD contrast one level.
The LCD contrast is adjusted one level up.
–or–
Press the Page Down button once to decrease the LCD contrast one
level.
The LCD contrast is adjusted one level down.
3 Release the Backlight button when the contrast is satisfactory.
The LCD contrast can be adjusted 16 levels.
Note: To adjust the contrast multiple levels, you have press the Page Up or Page Down button multiple times. When you press
and hold the Page Up or Page Down button, the LCD contrast will only change one level.

- Operating Devices

To operate devices on your RC3200 you have to switch to the Device overview. This screen displays the available devices like
TV, VCR, DVD, PreAmp and so on.

- Adjusting the Settings

The RC3200 settings can be adjusted in the Setup mode.
Press and hold the Mode button for 3 seconds.
- Adjust the LCD Timeout
The LCD timeout indicates how long the LCD touch screen stays active before it turns off. The LCD will only time out when
you don't touch any buttons. You can set the timeout between 1 second and 120 seconds.
Press '+' to increase or '-' to decrease the time the LCD stays active.
Tap '+' or '-' once to adjust the timeout 1 second up or down.
Press and hold '+' or '-' to adjust the timeout per 10 seconds up or down.

- Working with Modes

RC3200 starts up in Use mode. In this mode you operate your devices. For customizing the RC3200 (adjusting the settings,
defining brands, learning buttons, labeling buttons and devices or recording macros) you have to switch to the appropriate
mode via the menu that appears when you press and hold the mode button.
The RC3200 can be put into 4 different modes. These modes are:
Use mode: Normal operating. See 'Operating Devices'
Setup mode: For changing the RC3200 system settings. See 'Adjusting the Settings' for more details.
Learn mode: For learning commands from other remote controls. See 'Learning Commands' for more details.
Macro mode: For recording macros. You can assign multiple commands to one single button. See 'Recording Macros' for
more details.
Note :Learning commands and recording macros is not possible from either of the Home pages. You must select a device or
the Macro group first, then press and hold the Mode button perform.
- Learning From Other Remotes
If you own any non-Marantz components, you can program RC3200 to reproduce IR signals from your existing remote
controls via RC3200's learning eye. To do this, place RC3200 and the device's remote control on a flat surface, 1 to 4 inches
(2 to 10 cm) apart.
To learn commands from other remote controls, RC3200 has to be in Learn mode. Switching to Learn mode is only possible
from a specific device, not from the Home Page. See 'Working with Modes'
Per device you can learn all soft and hard buttons on the RC3200, except for:
• the Backlight button;
• the Back and FWD buttons;
• the Page Up and Page Down buttons;
• the "S" (Status) button;
• the Home button.
The Learn Sequence
1 From the Home page, select the device, e.g. TV, with the buttons you want to teach new commands to.
2 Press and hold the Mode button for 3 seconds. The Mode screen appears.
3 Tap Learn on the Mode Menu. RC3200 is now in Learn Mode. 'Learn' and the label of the selected device appear at the top
of the touch screen.
4 Use, if necessary, the Page Up or Page Down button to go to the next button you want to learn.
5 Press the soft or hard button you want to learn on theRC3200. The Learn label changes to Learning, which means RC3200
is ready to receive commands from an existing remote control. The RC3200 will wait for 3 seconds to receive an IR code from
another remote control.
Note: When a hard button is pressed to learn, there is no on screen feedback to indicate which button is pressed.