Lcd Back-Light Function; Specifications; Care And Maintenance; Signal Output - General MM70D User Manual

wood specIes (groUps) selectIon
In the normal mode, it is able to use
(group) for getting the more accurate moisture value. The selected
wood species (groups) symbol will display on the LCD below.
This instrument has 8 groups of wood species (groups), available to
press for circle selection.
Every time turn on, wood species (groups) will be set at NO. 1. T
he selected number before turning off will not be recorded.

lcd back-lIght FUnctIon

On: In the normal mode, press and hold
1.5 seconds to turn on back-light.
Off: When back-light is on, press and hold
1.5 seconds to turn off back-light.
If there is not any operation within 30 seconds, back-light will be
turn off automatically.
Back-light function will deplete power speedily. If it is not
necessary, please use back-light as little as possible.
calIbratIon and adjUstMent FUnctIon
This instrument has been adjusted completely before ex-factory. If the
condition is special and needs to adjust the instrument, please operate
the instrument following the steps below:
1. When the power is off, keep the
to turn on, CAL will appear on the display left below and the
instrument will "beep" every 4 seconds, it represents the
instrument is in the adjustment mode.
2. Please use the small
"CAL" at the right side of the instrument to display the value and
get the calibration value.
3. When calibration is finished, please turn off the power to store
data.
Before adjusting, please check if the power is enough and then
process the calibration.
When adjustment, please make sure the needles are suspended in
midair and with no contact on any object.
The built-in calibration value of this instrument is 18.4%±1%.
power InspectIon FUnctIon
The display left above has a power indicator symbol. If the power is not
enough, the symbol will flash and make a "beep" warning by fits and
starts. Please replace the new batteries immediately and then operate
the instrument.

sIgnal oUtpUt

This instrument has DC 0~1V (10mV ) synchronal output function, and
it can be used to connect the related peripheral device like a recorder,
controller, data-logger.....etc.
to select wood species
key over
key over
key pressed and press
type screw driver to do fine-tuning on

care and MaIntenance

1. This instrument has the accurate temperature compensation
function, but if it is used in a place with high temperature or high
humidity, it will produce deference or an error message.
2. The sensor (needles) is the electric conduction element of
connecting the measured material. In order to avoid damage to
the instrument and electric shock, when the measured material
has voltage or static electricity, please clear the voltage or cut off
the power and then go to measure.
3. Please use the two needles to pierce into the material at the
same time and keep them for a while to get a more accurate
value.
4. For harder material or the material needing deep inspection,
please change to use the special needle (optional).
5. To avoid the incorrect reading, if the low symbol appears, please
replace the battery before using.
6. The sensor (needles) is the main element. If the sensor has
damage or other problems, please replace the new one to use
continually.
7. When not in use, please remove the battery from the instrument.
Put the main instrument and all accessories into the protection
case and keep the kit in a dry, dust-free environment out of direct
sunlight.
8. Please contact the local agent or our customer service
department for any question(s) or product repair.

specIFIcatIons

• Measuring Range: 5.5 to 99.9% H
• Resolution: 0.1%
• Operating Range: - 4° to 122°F, <90%RH, non-condensing
• Accuracy (at 25°C): ±1% Wood scale
• Display: Digital dual LCD display with multi-function indicator
• Sampling Rate: 0.3 seconds
• Wood Group Scales: select from 8 wood species groups
• Data Memory: 99 readings
• Signal Output: Analog DC 0 ~ 1V (10 mV / 1%), load > 500
• Calibration: Built-in calibration adjustment
• Power Source: 1 "9V" battery
• Battery Life: About 250 hours of continuous use (no back-light)
• Dimensions: 6.0" x 2.2" x 1.26" (153 x 56 x 32 mm)
• Weight: 5.5 oz (155 g) (including battery)
• Functions:
g Back-Light luminescence EL
g Automatic temperature compensation
g Manual / automatic power off
g Data-Hold, Records Min/Max and Average values
g Battery symbol and low power warning
g Usable and changeable of extension probe
O %WME
2