Barco HDF W series Quick Start Manual page 2

HDF W series Quick start guide
Communication panel
IN DMX OUT REMOTE CTRL
RS232/422 IN
1 2
3
12V /1A
1 2 3 4 5
WIFI antenna for wireless IP (optional) 10/100 base-T for external control over IP and Art-Net
1 7
12V 1A output 8 Ethernet status lights
2
DMX interface input - output Projector Status lights
3 9
XLR input for wired projector control WIFI status lights
4 10
RS232 for serial communication IR receive sensor
5 11
USB backup custom settings GSM antenna input (optional)
6 12
Menu structure
INPUT IMAGE
Slot Module Type Image Settings
Input Locking Aspect Ratio
Native Resolution Timings
No Signal Image File Services
EDID Save Custom Settings
3D* Splash image
FLMW-Quickstartguide4.indd 2
Connections
DUAL LINK DVI-I HDCP
INPUT
10/100 BASE-T
1
ETH WIFI •
Dual Link DVI-I HDCP input accepts:
USB ACT PWR LMP SEL
RGB HV/YUV HV
10/100 ERR IR ACT Single DVI
Dual link DVI
6 7 8 9 10 11 12
BARCO
R/P G/Y/VIDEO
R
•
5 Cable Input accepts:
RGB HV/YUV HV
Composite video
S-Video
LAyOUT LAMPS ALIGNMENT
Main Window Lamp Power Orientation
PiP Window Identification Lens
Layout File Services Z-axis Warping
Same Zoom/Focus Blanking
Contrast/Intensity
Gamma
Internal patterns
Color Space
ScenergiX
* Only available with optional 3D input
Printed on FSC certified paper (www.fsc.org) R5905175 Rev. 01
Standard inputs
3G/DUAL HDSDI
SEL SEL
SEL
SYNC
SYNC SYNC
IN1 OUT1 IN2
2
•
3G/DUAL HDSDI input accepts:
3G : standard SMPTE 425M
HDSDI : standard SMPTE 292M
Dual link : standard SMPTE 372M
SDI : standard SMPTE 259M
Optional input
Input R/P R G/Y/Video B/P B
RGBHV R G B
5-CABLE INPUT R9864010
SEL
RGBS R G B
RGSB R B
G S
SYNC
B/P H/S V/C
B R RGBCV R G B
Composite - Video -
Video
S-Video - Y -
Component P R /R-Y Y P B /B-Y
Video-S
Component P R /R-Y YS P B /B-Y
Video-SOY
YUV-CV R-Y Y B-Y
PROjECTOR CONTROL SERvICE
Projector Address Identification
Serial communication Diagnostics
Network Int. Service Patterns
IR control Convergence
DMX Factory Default
Buttons USB Memory
Menu Position Reset Formatter
Local LCD Refill mode
Change Language Save Custom Settings
Scheduler Sp. HD Camera Mode
Auto Dim overtemp.
Time and Date
Optional 3D input
R9864000
3D INPUT
BARCO
SEL SEL
OUT2 SYNC SYNC
3D SYNC IN DISPLAYPORT HDMI 3D SYNC OUT
•
3D Input accepts:
3D sync in
Display port 1.1a up to 210 MHz
HDMI 1.4a up to 210 MHz
H/S V/C R
H V
Using the remote control or local
S -
17
keypad
- -
1
CV - 16
2
15
- -
Pattern to display test patterns
1
MENU
EXIT
- C
RGB to toggle colors
2
3
14
S -
4 Address to enter projector address
3
13
5
ENTER
Lens to open lens adjustments menu
4
- -
6 12
PAUSE LENS TEXT Pause to switch to pause
5
7
CV - 6 Standby to switch to standby
PHASE
9 0 Fn to toggle the display to the preview image
7
8
SHARPN
8 Auto image to activate the auto image adjustment
7 8
TINT
5 6 Digit keys Direct input selection or numeric entries
11 9
9 COLOR
Lens keys to direct lens adjustment
3 4 10
BRIGHTN
Settings
1 2 11
CONTR
Phase: to adjust phase (analog signals only)
LENS LENS
10 ZOOM SHIFT
Sharpness: to increase edge detail
LENS
LENS
Tint: to adjust tint (NTSC only)
FOCUS SHIFT
Color: to adjust color saturation
Brightness: to adjust the low lights
Contrast: to adjust the high lights
9 14
12 Freeze to freeze the current image
Text to activate or deactivate the OSD
13
1 2 3 4 5
MENU EXIT
Navigation and Menu keys
14
6 7 8 9 0
Window to select the active window
15
RGB PATTERN WINDOW PIP LENS
F PiP to activate selected Picture in Picture
16
N
ENTER
STBY AUTO
PAUSE TEXT
Info to activate help information on a menu item
17
2 6 1 5 13 15 8 16 7 4
IMPORTANT:
• Remove the lens before trans-
porting the projector.
R9864140
• To save lamp lifetime, first
switch the projector to standby
mode and wait until the after
cooling is finished to switch off
the main power.
• Ensure that the projector is oper-
ating with clean filters.
• Do not block the ventilation in
and outlets
• Laser light can cause severe
damage to the DMD. This damage
is not covered by warranty.
16-11-2012 11:21:20