Coinco CoinPro 3 Operation And Service Manual

Coinco CoinPro 3 Operation And Service Manual

9302-gx series electronic changer

Advertisement

Coinco 9302-GX SERIES
ELECTRONIC CHANGER
Operation and Service Manual

Advertisement

Table of Contents
loading

Summary of Contents for Coinco CoinPro 3

  • Page 1 Coinco 9302-GX SERIES ELECTRONIC CHANGER Operation and Service Manual...
  • Page 2: Table Of Contents

    Table of Contents Section 1: General Information Introduction ......................3 For Your Records ....................3 Features ......................... 3 After Unpacking ....................3 Specifications ......................4 Section 2: Installation Installing the Changer .................... 5 Option Switch Setting .................... 5 Section 3: Operation Coin Recognition ....................
  • Page 3: Section 1: General Information

    Coinco CoinPro 3, 9302-GX coin changer. ship your changer in the future. If the coin changer is being stored or used as a...
  • Page 4: Specifications

    Section 1: General Information SPECIFICATIONS Coin Tube Capacity 5¢ 10¢ 25¢ Power Requirements tube tube tube · 34VDC · 3.6 Amp max. at 26VDC for 100 ms every 500 LO 25¢ LO 25¢ ms during payout Option Option · 750 m Amp max. for 1 second for each coin Switch Switch accepted...
  • Page 5: Section 2: Installation

    Section 2: Installation INSTALLING THE CHANGER 1=USA/CAN Not Used 2=LO 25¢ ON: Quarters are directed to cash box once change tube has 1. Remove power from vendor. approximately 28 quarters 2. Remove the acceptor from the changer by OFF: Quarters are put into change releasing acceptor latches and pulling the top of tube until it is full.
  • Page 6: Section 3: Operation

    Section 3: Operation COIN RECOGNITION REJECTED COIN See Figure 3 See Figure 4 As a coin enters the changer through the acceptor If a coin is rejected for any reason, both the UPPER funnel, its impact is absorbed by a white ceramic rail (coin tube) and the LOWER (cash box) gate will which debounces the coin and allows it to continue remain closed.
  • Page 7: Accepted Coin

    Section 3: Operation ACCEPTED COIN cash box via the changer cash box chute. If the appropriate coin tube is not full (full sensor not See Figures 5 and 6 covered by coins), the coin tube gate will open An accepted coin will be routed to either the vendor directing the coin down a ramp.
  • Page 8: Credit & Accumulation

    Section 3: Operation CREDIT AND ACCUMULATION See Figure 7 There are two sensors, one in the separation section of the acceptor and one in the cash box path of the acceptor. As coins pass either one of these sensors, the changer sends credit information to the vendor electronic controller where the coin credit is accumulated.
  • Page 9: Change Storage

    Section 3: Operation CHANGE STORAGE INTERFACE BETWEEN THE See Figure 8 9302-GX COIN CHANGER AND VENDOR / CONTROLLER The full tube sensors in each coin tube continually report the (full/not full) status to the coin changer See Figures 9 and 10 logic board.
  • Page 10 Section 3: Operation Figure 9 9302-GX Controller/Vendor Interface Figure 10 Page 10...
  • Page 11: Section 4: Maintenance

    Section 4: Maintenance ROUTINE MAINTENANCE Payout Assembly With payout solenoids disconnected from main logic Routine maintenance will improve performance and board, remove the four screws - two from each side- extend the working life of the 9300 series changer at the bottom of the housing. Separate payout and reduce the need for more involved repairs.
  • Page 12: Disassembling Payout Base

    Section 4: Maintenance DISASSEMBLING PAYOUT BASE FOR CLEANING Remove the four Phillips head screws from the bottom plate. Remove bottom plate and individual slides. Clean parts with mild detergent and hot water as desired. DO NOT SUBMERGE SOLENOIDS IN WATER. Replace slides making sure part numbers face up into changer.
  • Page 13: Section 5: Bench Check Procedure

    Section 5: Bench Check Procedure BENCH CHECK PROCEDURE FOR MODEL 9302-GX Using Coinco Tester #407341 NOTE: This tester is a static sensitive device and must be used in a grounded work station. PROCEDURE RESULT FUNCTION VERIFIED Set changer Coin Control Option switches as follows: #1: (OFF) Not Used.
  • Page 14 Section 5: Bench Check Procedure BENCH CHECK PROCEDURE PROCEDURE RESULT FUNCTION VERIFIED Turn tester power OFF. Remove Upon power up, the High Tube Sensor acceptor from changer. Block digital display and tube sensors the coin change high tube sensors upper and lower LED's sequence. by completely filling tubes with Coins are accepted and directed to coins or by inserting a rolled up...
  • Page 15 Section 5: Bench Check Procedure BENCH CHECK PROCEDURE PROCEDURE RESULT FUNCTION VERIFIED Actuate changer coin return lever Digital display will read ESC Escrow return Manually operate each of the Each dispensing solenoid will Manual dispense changer's "Inventory" energize, dispensing a coin, ($.05, $.10, $.25) switches until all coins are dispensed.
  • Page 16: Tester Error Codes

    Section 5: Bench Check Procedure TESTER ERROR CODES “ACPT” - Acceptor Unplugged This error occurs when the changer does not The following is a list of error codes the changer communicate with the acceptor. tester will display via the digital display: “RoCh”...
  • Page 17: Section 6: Troubleshooting

    If a changer cannot be repaired by check the following before replacing any parts: following the guide, return the changer to the nearest Coinco Service Center for repair. If it is necessary • Connectors are inserted correctly. to return the changer to Coinco, please accompany •...
  • Page 18 Section 6: Troubleshooting 9302-GX TROUBLESHOOTING GUIDE TROUBLE POSSIBLE CAUSE PROCEDURE REMEDY No coin acceptance Coin return lever Make sure changer is mounted Reposition changer or rejects percentage correctly and coin return lever and/or vendor of good coins is in proper position coin return lever.
  • Page 19 Section 6: Troubleshooting 9302-GX TROUBLESHOOTING GUIDE TROUBLE POSSIBLE CAUSE PROCEDURE REMEDY Accepted quarters go Quarter coin tube Check to see that quarter coin Fill quater coin to quarter coin tube when has less than 22 tube has a minimum of 22 tube with 22 Lo-$.25 switch is ON quarters...
  • Page 20: Wiring Diagram

    Section 6: Troubleshooting 9302-GX Wiring Diagram Page 20...
  • Page 21: Section 7: Exploded Views

    Section 7: Exploded Views Modular View 9302-GX Item No. Part No. Description Qty. Note 407007 Harness 407400-3 Logic Board Gray Connector 407400-2 Logic Board Black Connector 922331.7 Changer Housing 407978-4 Payout Assembly 406728-12 Inventory Tube Assembly 407755-2 Acceptor Gray Connector 407755-1 Acceptor Black Connector...
  • Page 22: Changer Housing

    Section 7: Exploded Views Changer Housing Item No. Part No. Description Qty. 922331.7 Housing (only) 902011-1 Acceptor Latch, Right 902010-1 Acceptor Latch, Left 909729 Label, Indentification Page 22...
  • Page 23: 9302-Gx Payout Assembly

    Section 7: Exploded Views 9302-GX 406739-4 Payout Assembly Item No. Part No. Description Qty. 406607-4 Solenoid Assembly, 24VDC 909113 Pivot Shaft 909141 Upper Payout Base 909630 Screw, 6-32 x 3/16 909105 10¢ Payout Slide 909104 5¢ Payout Slide 909103 25¢ Payout Slide 909102-1 Lower Payout Base 345P4R7...
  • Page 24: Logic Board Cover Assembly

    Section 7: Exploded Views Logic Board Cover Inventory Tube 408038-1 Assembly 406728-12 Assembly Item Part Item Part Description Quantity Description Quantity 909115-4 Inventory Tube 922332-3 Logic Bd. Cover Label 910889-2 Label, Switch 406728-12 Inventory Tube & Options Board Assembly Page 24...
  • Page 25: Acceptor Front View

    Section 7: Exploded Views Acceptor Front View 407755-2 Assembly Item Part Item Part Description Quantity Description Quantity 406184-2 Gate & Coil Assy. 906618 Spring, Oper. Lev. 406567 Gate Bd. Assy. LED 400-8 Nut, 8-32 Lock 906596-1 Cover 406611 Mainplate & Coil Assy. 909095-2 Front Cover Assy.
  • Page 26: Acceptor Back View

    Section 7: Exploded Views Acceptor Back View 407755-2 Assembly Item Part Item Part Description Quantity Description Quantity 406611 Mainplate & Coils 906622-2 Pin, Diverter Pivot 406167 Plunger & Yoke 345S4R7 Screw, 4x7/16 PH Assembly 906600-1 Diverter Door, 906619-2 Spring, Upper Copper-plated 909092 Diverter Door,...
  • Page 27 Notes Page 27...
  • Page 28 COIN ACCEPTORS, INC. 300 Hunter Avenue St. Louis, MO 63124-2013 Coinco Publication No. 925054 Rev. 1 (314) 725-0100 or (800) 325-COIN 8/00 Printed in the U.S.A.

Table of Contents