Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Horizon Hobby Clipped Wing Cub
Summary of Contents for Horizon Hobby Clipped Wing Cub
- Page 1 Clipped Wing Cub Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni SAFE ® Select Technology, Optional Flight Envelope Protection www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de...
-
Page 2: Safety Precautions And Warnings
Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warn- ings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury. -
Page 3: Table Of Contents
Box Contents Quick Start Information Transmitter Set up your transmitter using the Setup transmitter setup chart Hi Rate Low Rate p20mm p13mm q20mm q13mm Dual Rates 20mm 13mm 30mm 20mm Center of 60 –70 mm back from leading edge of wing at the fuselage. Gravity (CG) Flight Timer 5 minutes... -
Page 4: Select Technology
3. Set AICRAFT TYPE: recharge the light battery. See the Low Voltage Cutoff (LVC) section for more WING: NORMAL details on maximizing battery health and run time. DX10t DX18 4. Go to the FUNCTION LIST Clipped Wing Cub www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de... -
Page 5: Model Assembly
Model Assembly Landing Gear Installation 1. Turn the fuselage so the bottom side is facing up. 2. Secure the Landing Gear assembly (A) into place with the six included screws (B). Disassemble in reverse order. www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de... -
Page 6: Model Assembly Continued
• Loosen the screw on the connector attached to the servo horn. Slide the control rod in or out until the control surface is centered. • • Tighten the connector screw when inished. Clipped Wing Cub www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de... - Page 7 Model Assembly Continued Wing Installation 1. Connect the Aileron connectors from the wing to the respective Y-harnesses connectors from the receiver. The left and right servos can be connected to either side of a Y-harness. IMPORTANT: The ailerons must be connected to the receiver’s AILE (#2 channel) with a Y-harness (included) for the AS3X system to function properly.
- Page 8 (F) and 2 screws (G). 3. Secure the front section of the loats using the two included screws (H) to secure the front support members to the bottom of the fuselage. Disassemble in reverse order. Clipped Wing Cub www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de...
-
Page 9: Transmitter And Receiver Binding
Transmitter and Receiver Binding / Switching ON and OFF SAFE Select This product requires an approved Spektrum ™ DSM2 ® /DSMX ® compatible transmitter. Visit www.bindnly.com for a complete list of approved transmitters. Bind Plug Installation The aircraft has an optional SAFE Select technology, which can be switched ON or OFF easily by binding in a speciic manner as described below. -
Page 10: Select Switch Designation
After lying, you may choose to adjust the linkage positions for the desired • control response. See the table to the right. Rudder More control throw Less control throw Clipped Wing Cub www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de... -
Page 11: Battery Installation And Esc Arming
Battery Installation and ESC Arming Battery Selection ® We recommend the E-lite 2200mAh 11.1V 3S 30C Li-Po battery (EFLB22003S30). Refer to the Optional Parts List for other recommended batteries. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the E-lite Li-Po battery packs to it in the fuselage. -
Page 12: Center Of Gravity (Cg)
Refer to the receiver manual for more information. Once the AS3X system is active, control surfaces may move rapidly. This is normal. AS3X remains active until the battery is disconnected. Clipped Wing Cub www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de... -
Page 13: In Flight Trimming
In Flight Trimming During your irst light, trim the aircraft for level light at 3/4 throttle. Make small trim adjustments with your transmitter’s trim switches to straighten the aircraft’s light path. 3 Seconds After adjusting the trim, do not touch the control sticks for 3 seconds. This allows the receiver to learn the correct settings to optimize AS3X performance. -
Page 14: Pnp Receiver Selection And Installation
CAUTION: Incorrect installation of the receiver could cause a crash. 3. Attach the appropriate control surfaces to the their respective ports on the receiver using the chart in the illustration. Clipped Wing Cub www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de... -
Page 15: Post Flight
Post Flight Disconnect the light battery from the ESC (Required for Safety Repair or replace all damaged parts. and battery life). Store the light battery apart from the aircraft and monitor the Power OFF the transmitter. battery charge. Remove the light battery from the aircraft. Make note of the light conditions and light plan results, planning for future lights. -
Page 16: Troubleshooting Guide
Weather conditions might be too cold Postpone flight until weather is warmer then motor loses Battery is old, worn out, or damaged Replace battery power Battery C rating might be too small Use recommended battery Clipped Wing Cub www.modellmarkt24.ch; www.modellmarkt24.ch; www.modellmarkt24.de www.modellmarkt24.de... -
Page 17: Ama National Model Aircraft Safety Code
AMA National Model Aircraft Safety Code Effective January 1, 2014 A. GENERAL B. RADIO CONTROL A model aircraft is a non-human-carrying aircraft capable of sustained light 1. All pilots shall avoid lying directly over unprotected people, vessels, in the atmosphere. It may not exceed limitations of this code and is intended vehicles or structures and shall avoid endangerment of life and property exclusively for sport, recreation, education and/or competition. -
Page 18: Limited Warranty
Product, (iv) attempted service by problem. A copy of your original sales receipt must be included for warranty anyone other than a Horizon Hobby authorized service center, (v) Product not consideration. Be sure your name, address, and RMA number are clearly purchased from an authorized Horizon dealer, or (vi) Product not compliant written on the outside of the shipping carton. -
Page 19: Contact Information
Compliance Information for the European Union EFL Clipped Wing Cub BNF Basic (EFL5150) EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED and EMC Directive. -
Page 20: Replacement Parts
Hélice/Cône Clipped Cub 1,2 m Elica/ogiva: Clipped Cub 1,2 m 1.2m Clipped Wing Cub Motor Moteur 1 000 Kv Clipped Wing Cub EFL5166 1,2 m Clipped Wing Cub Motor 1000 kV Motore 1000 kv: Clipped Cub 1,2 m 1000kv 1,2 m EFLA1040U 40A ESC: Ultimate 2 Ultimate 2: 40A ESC Regler Ultimate 2 - Contrôleur 40A... - Page 21 E-lite, AS3X, DSM, DSM2, DSMX, the DSMX logo, Bind-N-Fly, SAFE, the SAFE logo, Z-Foam, ModelMatch, Dynamite, EC3, Prophet and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Need help?
Do you have a question about the Clipped Wing Cub and is the answer not in the manual?
Questions and answers