Table of Contents
Advertisement
Quick Links
SP-RANGE
INSTALLATION AND OPERATING MANUAL
PLEASE LEAVE WITH OPERATOR
SP12 & SP25 – SERIES 4
Imperial Machine Company Limited
Unit 1, Abbey road
Wrexham Industrial Estate
Wrexham, LL13 9RF
Tel: +44 (0)1978 661155
Fax: +44 (0)1978 729990
Service Fax: +44 (0)1978 667766
Spares Fax: +44 (0)1978 667759
E-mail:
info@imco.co.uk
Website: www.imco.co.uk
A34/013 R14
ECN 8308 June 2015
Advertisement
Table of Contents
Related Manuals for IMC SP12
Summary of Contents for IMC SP12
- Page 1 SP-RANGE INSTALLATION AND OPERATING MANUAL PLEASE LEAVE WITH OPERATOR SP12 & SP25 – SERIES 4 Imperial Machine Company Limited Unit 1, Abbey road Wrexham Industrial Estate Wrexham, LL13 9RF Tel: +44 (0)1978 661155 Fax: +44 (0)1978 729990 Service Fax: +44 (0)1978 667766...
- Page 2 Unit 1, Abbey Road, Wrexham Industrial Estate, Wrexham, LL13 9RF Declare under our sole responsibility that the machine SP12 & SP25 SERIES 4 As described in the attached technical documentation is in conformity with the Machine Safety Directive 98/37/EC and is manufactured under quality system BS EN ISO 9001. It is also in...
-
Page 3: Table Of Contents
SP-Range GUARANTEE ....................... 1 DELIVERY ......................1 SAMPLE RATING LABEL ................... 1 INTRODUCTION ....................2 YOUR PEELER ....................2 CONTROLS ......................3 INSTALLATION ....................3 WATER SUPPLY ....................4 WASTE OUTLET CONNECTION ................. 4 WASTE EJECTOR ....................5 Fitting the waste ejector ................. 5 Waste Ejector adjustments ................ -
Page 5: Guarantee
SP-Range GUARANTEE This equipment is guaranteed by IMC for 2 years from the date of its purchase from IMC, or from one of its stockists, dealers or distributors. The guarantee is limited to the replacement of faulty parts or products and excludes any consequential loss or expense incurred by purchasers. -
Page 6: Introduction
SP-Range INTRODUCTION This machine is intended for peeling potatoes. Its use may be extended to other root vegetables. It is not recommended to use this machine for peeling onions. YOUR PEELER SPLASH COVER CONTROL BOX DOOR CHUTE MOUNTING BRACKET DOOR HANDLE WASTE OUTLET... -
Page 7: Controls
For the Installer: These Instructions contain important information designed to help the user obtain the maximum benefit from the investment in an IMC SP Peeler. Please read them carefully before starting work, and consult with the supplier in the event of any queries. -
Page 8: Water Supply
If required, secure with the hose clip supplied. Longer lengths of flexible hose are available from IMC on request. The waste outlet also incorporates a 2” BSP female thread for connection to standard 54mm (2”) waste pipe. -
Page 9: Waste Ejector
SP-Range WASTE EJECTOR The waste ejector is an optional fitting that dilutes the waste sludge to enable it to flow easily through the drains without fear of blockage. Waste Ejectors are not recommended in the follow circumstances; · A pipe run exceeding 15m between the machine and main drain ·... -
Page 10: Electricity Supply Connection
A dedicated supply to the socket is recommended and it should be protected by a C or D class circuit breaker rated at 10A for the SP12 and 16A for the SP25. Three phase machines should be connected to a 15A isolator providing at least 3mm separation in all poles. -
Page 11: Commissioning
The direction of rotation of single phase units is set at the factory. If it is not rotating in the correct direction contact IMC. To change the direction of rotation of three phase units, switch off the machine, isolate the supply and interchange any two phase wires. -
Page 12: Safety
SP-Range SAFETY All SP-Range peelers are controlled so that if the electricity supply is interrupted the machine will not restart automatically. All single phase SP-Range controls are fitted with a thermal trip. This ensures that the controls cannot overheat and become damaged. If the thermal trip cuts in, the machine will not run until it has cooled down and the peeler is switched off and on again. -
Page 13: Do's And Don'ts
SP-Range DO’S AND DON’TS Install on a level service. Ensure power supply isolator or socket is accessible with the peeler installed. Clean the machine after each period of use. Don’t PAT test single phase machines, as they have an inverter inside the control box, which invalidates any earth leakage tests. -
Page 14: Maintenance
MAINTENANCE Other than regular cleaning the SP-Range of peelers require no maintenance by the end user. It is recommended that the unit is serviced by an IMC approved engineer at least once a year. The motor in the single phase units is controlled via an inverter. The following warnings must be observer before working on this unit. -
Page 15: Wiring Diagram 1Ph Units
SP-Range WIRING DIAGRAM 1PH UNITS... -
Page 16: Wiring Diagram 3Ph Units
SP-Range WIRING DIAGRAM 3PH UNITS... -
Page 17: Parts Illustration
SP-Range PARTS ILLUSTRATION... -
Page 18: Spares Part List
E58/096 Wall Bracket (1ph) E58/111 Wall Bracket (3ph) E58/111 Wall Bracket (3ph) S58/587 SP12 Control Box 1ph (Inverter) S58/588 SP25 Control Box 1ph (Inverter) (Inc. Wall Bracket & cables) (Inc. Wall Bracket & cables) S58/595 SP12 Control box 3ph S58/596 SP25 Control box 3ph (Inc. -
Page 19: 1Ph Control Box Spare Parts List
SP-Range 1PH CONTROL BOX SPARE PARTS LIST SP12 SP25 Item Part No Description Part No Description E58/096 Mounting Bracket E58/096 Mounting Bracket E58/097 Wall Bracket (Not shown) E58/097 Wall Bracket (Not shown) G76/031 M2 Control Box G76/031 M2 Control Box... -
Page 20: 3Ph Control Box Spare Parts List
SP-Range 3PH CONTROL BOX SPARE PARTS LIST 15 16 17 SP12 SP25 Item Part No Description Part No Description E58/117 Mounting Bracket E58/117 Mounting Bracket E58/119 Wall Bracket E58/119 Wall Bracket G76/041 M1 Control Box (inc lid) G76/041 M1 Control Box (inc lid)