Reclining The Backrest - CYBEX Callisto User Manual

6. ADjUSTING THE HARNESS SYSTEM FOR NEWBORNS
– Release the loops at the end of the shoulder straps from the triangle in the belt system,
situated at the bottom of the backrest under the seat cover.
– Completely pull the shoulder straps out of the holes in the backrest.
– Feed the shoulder straps through the two bottom holes. make sure to feed the straps back
through the holes in the backrest mechanism and re-attach them to the triangle.
– to adjust the length of the shoulder straps to newborns please attach the inner loop of the
shoulder strap ends to the triangular ring.
Switch back to the upper holes as soon as the shoulder straps do no longer fit over the child´s
shoulders.
7. REMOVING THE HEADHUGGER AND SHOULDER PADS
a) Remove the headhugger as soon as the headhugger does no longer fit over the child´s
shoulders.
b) Remove the velcros of the headhugger on the top left and right side on the back of the
seat cover. Release the loops at the end of the shoulder straps from the triangle in the belt
system, situated at the bottom of the backrest under the seat cover.
– Completely pull the shoulder straps out of the holes in the backrest.
c) pull the shoulder straps through the shoulder pads and the headhugger. make sure to
feed the straps back through the holes in the backrest mechanism and attach them to the
triangle.
You can use the haedhugger and the shoulder pads separately.
8. ATTACHING THE BUMPER BAR
a) Slide in latches on left and right side into gadgets sewn into the seat fabric.
b) press buttons on left and right end of the bumper bar to take it off.
9. RECLINING THE LEG REST
a) press the leg rest on both front edges and push down.
b) Simply lift the leg rest to put it back to the starting position.

10. RECLINING THE BACKREST

a) pull the recline lever on the back of the seat to recline the backrest.
b) to raise it again just lift the backrest of the seat. the backrest can be engaged in 5 different
positions.
11. ADjUSTING HEIGHT OF THE HANDLE
a) b) push button underneath the handle bar and slide up upper part of handle bar to extend
it until it clicks in place. Shorten the handle bar by pushing the button again.
12. FOLDING THE STROLLER
– Remove all contents from the basket. if attached, ensure the canopy is folded back.
a) lift the central lever located at the back of the shopping basket.
b) push down the lock lever (extended bar on the right side of the locking system).
c) d) press the button at the handle bar and fold the buggy by pushing it slightly forward.
please note: Keep the button pushed the whole time. to make folding easier lift
the locking lever with your foot. Fold the buggy together carefully until the safety clip is
securely locked.
4
e) the brake can be used even with a folded buggy. with a locked brake the folded buggy
can rest against a wall to prevent inadvertent rolling.
13. CARRYING THE STROLLER
– pull the flexible carring handle on right rear tube and lift the stroller.
14. REMOVING THE SEAT COVER
– Slightly fold the stroller to reduce tension.
– Remove the canopy from the stroller, if attached.
a) take the seat cover's hooks (3) off the frame on left and right side
– open the press buttons (4) of the straps connected to the seat side panels and the basket
rear tube.
– open the flaps (5) which are fixed with velcro over the tubes, one on each side.
– Feed the strap with the slider (6) of the central harness buckle through the hole in the seat
fabric.
b) Feed the loops on the end of the shoulder straps through the triangle in the backrest (7).
c) Feed the shoulder straps through the holes in the seat fabric (8).
– open the press buttons which are on the left and the right side from the seat on the bottom
from the fabric.
– pull the seat cover over the belt shifting button on the seat.
– Slide the fabrics from the seat base tubes.
– Reverse this procedure to refit the seat cover and the harness. make sure that the seat
tubes slide back into the pockets inside the seat cover.
15. ATTACHING THE CANOPY
a) attach the canopy adaptor on to the inside of the frame tubes of the buggy.
b) to remove the canopy reverse procedure.
c) d) e) Extend the canopy and place canopy rear flap behind the seat.
f) lie-flat position: put the rear flap over the seat's back rest and fixate it with the two velcros
underneath.
g) h) i) the canopy is adjustable to various positions. the Canopy has a height adjustment
and a forward rotation function. to rotate open the zip located at the top of the canopy.
the canopy has a fully ratcheting function to create complete coverage. Simply pull on the
front of the canopy to the desired position. the height can be easily adjusted by simply sliding
the canopy up or down the frame. the entire canopy can also be tilted forward. For maximum
coverage, unzip the extra panel on top of canopy and pull forward.
j) the canopy flap at the rear of the stroller can be rolled up and fixed with a velcro fastener,
if required.
16. TO REMOVE THE COMPLETE SUB SEAT
– Remove the canopy
a) undo the press buttons that attach the seatcover with the rear frame.
b) unhook the side panels at the left and right upper end out of the adaptor.
c) open the adaptor on the left and the right side under the seat unit.
d) pull out the complete sub seat towards the front of the buggy.
e) to attach the subseat reverse this procedure. Ensure that the buggy is not completely
unfolded.