Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Harken 35.2 ST
Summary of Contents for Harken 35.2 ST
- Page 1 Installation and Maintenance Manual MRW-01 Radial Winch 35.2 ST...
-
Page 2: Table Of Contents
Maintenance Washing Maintenance table Disassembly procedure Exploded view with maintenance products Assembly Harken limited worldwide warranty ® Ordering spare parts Exploded view Parts list Radial Winch 35.2 STA Radial Winch 35.2 STC 35.2 ST Installation and Maintenance Manual Radial Winch... -
Page 3: Introduction
Maximum working load WARNING! The maximum working load (MWL) for the 35.2 ST Radial Winch is 650 Kg (1433 lb) Subjecting the winch to loads above the maximum working load can cause the winch to fail or pull off the deck suddenly and unexpectedly during high loads causing severe injury or death. -
Page 4: Installation
NOTICE You can find the icon on the skirt to identify the drive gear position. Once you have chosen the correct mounting position for the winch on the deck proceed with installation. 35.2 ST Installation and Maintenance Manual Radial Winch... -
Page 5: Procedure 1
2. Slide off the hub n°28 and the cover n°29 1. Unscrew the central screw ( 2Nm/18 in-lb) 3. Unscrew the three screws n°27 4. Remove the self-tailing arm n°26 by ( 4Nm/35 in-lb) rotating and lifting it. 35.2 ST Installation and Maintenance Manual Radial Winch... -
Page 6: Procedure 2
To identify the various parts, refer to the exploded view at the end of this Manual. 1. Remove the skirt n°2 with the help of 2. Take off the skirt n°2 the screwdriver placed as shown by the symbol 35.2 ST Installation and Maintenance Manual Radial Winch... - Page 7 Make sure the skirt is correctly clipped on to the base of the winch. Install the winch on the deck in the position you have chosen, keeping in mind the limits described on page 4 and using hexagonal headed bolts. (See paragraph on installation) 35.2 ST Installation and Maintenance Manual Radial Winch...
-
Page 8: Installation Procedure
C. Bolt the base of the winch to the deck using five M6 Socket Head (SH) bolts for Procedure 1 or five ® hexagonal headed M6 bolts for Procedure 2 (neither is supplied by Harken ), correctly chosen for the thickness and type of the boat deck. Consult the yard that built the boat in case of doubt. -
Page 9: Positioning The Self-Tailing Arm
Installation and maintenance of winches must be carried out exclusively by specialized personnel. ® In the case of doubt contact Harken Tech Service at techservice@harken.it Disassembly procedure Tools needed... - Page 10 8. Slide out the central shaft n°19 9. Unscrew the 6 hex screws n°16 ( 8Nm/71 in-lb) 10. Remove the drum support n°15 11. Remove the washer n°12 Important: washer n°12 may remain inside the drum support! 35.2 ST Installation and Maintenance Manual Radial Winch...
- Page 11 14. Slide off gear n°14 15. Slide off gear n°10 16. Remove the pawls n°5. To facilitate the 17. Remove washer n°9 operation press the spring against the pawl with a blade. 35.2 ST Installation and Maintenance Manual Radial Winch...
- Page 12 Use a brush to lightly lubricate all gears, gear pins, teeth and all moving parts with grease. Lightly lubricate the pawls and springs with oil. Do not use grease on the pawls! 35.2 ST Installation and Maintenance Manual Radial Winch...
-
Page 13: Exploded View With Maintenance Products
Exploded view with maintenance products Anti-seize Harken ® Grease ® Harken Pawl Oil Apply Harken grease on assy socket screw ® Apply Harken ® grease on drum gear 35.2 ST Installation and Maintenance Manual Radial Winch... -
Page 14: Assembly
Once in position, check that the pawls can be easily opened and closed with a finger. ® In case of doubt concerning the assembly procedure contact Harken Tech Service: techservice@harken.it 35.2 ST Installation and Maintenance Manual... -
Page 15: Harken ® Limited Worldwide Warranty
Refer to the Harken Limited Worldwide Warranty in the Harken Catalogue and on the website www.harken.com Ordering spare parts Spare parts can be requested from Harken ® ® described in the Harken Limited Worldwide Warranty, indicating the part number in the... -
Page 16: Exploded View
Exploded view 1/2 35.2 ST Installation and Maintenance Manual Radial Winch... - Page 17 Exploded view 2/2 35.2 ST Installation and Maintenance Manual Radial Winch...
-
Page 18: Parts List
Assy Socket W20-80 Screw M8x20 UNI 6109* Washer Ø7.7xØ25x5.8* Socket Handle W20/80* S 41295 00 A5 Cover 2 speed W35 *Service kit available; see winch kit section on the website www.harken.com **Winch product sticker 35.2 ST Installation and Maintenance Manual Radial Winch... -
Page 19: Radial Winch 35.2 Stc
Assy Socket W20-80 Screw M8x20 UNI 6109* Washer Ø7.7xØ25x5.8* Socket Handle W20/80 S 41295 00 A5 Cover 2 speed W35 *Service kit available; see winch kit section on the website www.harken.com **Winch product sticker 35.2 ST Installation and Maintenance Manual Radial Winch...