Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Harken 35.2 ST E
Summary of Contents for Harken 35.2 ST E
- Page 1 Installation and Maintenance Manual MRW-00 Powered Radial Winch 35.2 ST E...
-
Page 2: Table Of Contents
Ordering spare parts Exploded view Parts List Radial Winch 35.2 STA Radial Winch 35.2 STC Radial Winch 35.2 STCW Radial Winch 35.2 STBBB Radial Winch 35.2 STCCC Horizontal electric motor 12V/24V 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 3: Introduction
® In case of doubt the Harken Tech Service is at your disposal at techservice@harken.it ® This Manual is available only in English. If you do not fully understand the English language, do not carry out the operations described in this Manual. -
Page 4: Weight
Subjecting the winch to loads above the maximum working load can cause the winch to fail or pull off the deck suddenly and unexpectedly during high loads causing severe injury or death. 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 5: Outline
Outline Winch 35.2 ST E/HY Ø80,5 Ø149 Horizontal electric motor (12 V / 24 V) Ø149 Ø80,5 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 6: Installation
Once you have decided the correct mounting position for the winch on the deck and checked the space available below deck, proceed with the installation. 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 7: Procedure 1
2. Unscrew the central screw ( 2Nm/18 in-lb) 3. Slide off the assy socket n°28 and the cover 4. Unscrew the three screws n°27 n°29. ( 4Nm/35 in-lb) Pay attention to the o-ring in the socket. 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 8: Procedure 2
See (paragraph on installation) the limits described on page 6 and using socket head (SH) bolts. Torque to apply when assembling 1. Remove the skirt n°2 with the help of the 2. Take off the base n°2 screwdriver placed as shown by the sym- 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... - Page 9 Install the winch on the deck in the position you have chosen, keeping in mind the limits described on page 6 and using hexagonal headed bolts. (See paragraph on winch installation) 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
-
Page 10: Winch Installation Procedure
® B. Remove the winch and drill the five 6.2 mm and a 80 mm diameter holes. C. Bolt the base of the winch to the deck using five M6 bolts (not supplied by Harken ) as ®... -
Page 11: Positioning The Self-Tailing Arm
2. Tighten six M6 precote coated screws ( 8 Nm/ 71 in-lb) 3. Position the reduction gear and motor 4. Tighten the two screws ( 8 Nm/ 71in-lb). Be sure to align the flange. 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 12: Electric Wiring Diagrams
Refer to the following diagrams for the electric wiring: WARNING! Read the Dual Function Control Box manual carefully before installing and using the device. NOTICE For other installations, refer to the Dual Function Control Box manual. 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... - Page 13 10 Nm (88 in-lb). NOTICE Note that correct electrical contact sequence is: Nut – Cable Terminal – Self-Locking Washer – Lock Nut 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
-
Page 14: Maintenance
Installation and maintenance of winches must be carried out exclusively by specialized personnel. WARNING! Make sure that the power is switched off before installing or carrying out maintenance on the winch. In the case of doubt contact Harken Tech Service at techservice@harken.it ® Disassembly procedure Tools needed:... - Page 15 8. Unscrew the 6 hex screws n°16 9. Remove the assy housing n°15 ( 20Nm/177 in-lb) Important: washer n°12 may remain inside the drum support! 10. Remove the washer n°12 11. Remove the gear n°7 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
- Page 16 12. Remove the pawls carrier n°4 13. Remove the gear n°3 14. Remove the gear n°14 15. Remove the gear n°10 16. Remove the pawls carrier n°11 18. Remove the washer n°9 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
- Page 17 Use a brush to lightly lubricate all gears, gear pins, teeth and all moving parts with grease. Lightly lubricate the pawls and springs with oil. Do not use grease on the pawls! 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
-
Page 18: Exploded View With Maintenance Products
Exploded view with maintenance products Anti-seize ® Harken Grease Harken ® Pawl Oil 1. Apply Harken grease on assy socket screw - 2. Apply Harken grease on drum gear ® ® 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 19: Assembly
Before screw the central screw, check the correct position of the o-ring in the assy socket and apply Harken grease. ® In case of doubt concerning the assembly procedure contact Harken® Tech Service: techservice@ harken.it 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 20: Harken ® Limited Worldwide Warranty
Limited Worldwide Warranty in the Harken Catalogue and on the website ® ® www.harken.com Ordering spare parts Spare parts can be requested from Harken ® described in the Harken Limited Worldwide ® Warranty, indicating the part number in the W XXXXX... -
Page 21: Exploded View
Exploded view Exploded view Radial Winch 35.2 STA, STC, STCW EL/HY 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... - Page 22 Radial Winch 35.2 STA, STC, STCW EL/HY 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
- Page 23 Radial Winch 35.2 STBBB, STCCC EL/HY 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
- Page 24 Radial Winch 35.2 STBBB, STCCC EL/HY 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
-
Page 25: Parts List
S4129500A5 Assembly Housing Winch 35 A94131100 Disconnect Rod W35 EL/HY S414970002 Support W35 Heli-coil M6x9 S414890080 Bushing Ø9xØ11x7 Bushing Ø22xØ25x8.5 S4130900A7 *Available with service kit; see website www.harken.com **Winch product sticker 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 26: Radial Winch 35.2 Stc
S4129500A5 Assembly Housing Winch 35 A94131100 Disconnect Rod W35 EL/HY S414970002 Support W35 Heli-coil M6x9 Bushing Ø9xØ11x7 S414890080 S4130900A7 Bushing Ø22xØ25x8.5 *Available with service kit; see website www.harken.com **Winch product sticker 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 27: Radial Winch 35.2 Stcw
S4129500A5W Assembly Housing Winch 35 A94131100 Disconnect Rod W35 EL/HY S414970002 Support W35 Heli-coil M6x9 Bushing Ø9xØ11x7 S414890080 S4130900A7 Bushing Ø22xØ25x8.5 *Available with service kit; see website www.harken.com **Winch product sticker 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 28: Radial Winch 35.2 Stbbb
Cover 2 speed W35 BBB A76932700 S414890080 Bushing Ø9xØ11x7 Heli-coil M6x9 Winch Product Sticker** S4130900A7 Bushing Ø22xØ25x8.5 Disconnect Rod W35 EL/HY S414970002 *Available with service kit; see website www.harken.com **Winch product sticker 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 29: Radial Winch 35.2 Stccc
Housing Winch 35 Cover W35 CCC Bushing Ø9xØ11x7 A76811100 S414890080 Heli-coil M6x9 Winch Product Sticker** S4130900A7 Bushing Ø22xØ25x8.5 Disconnect Rod W35 EL/HY S414970002 *Available with service kit; see website www.harken.com **Winch product sticker 35.2 ST E/HY Installation and Maintenance Manual Radial Winch... -
Page 30: Horizontal Electric Motor 12V/24V
KIT EL Motor 24V 0,9kW Electric Motor Polarity motor sticker Screw stud M6x26 Washer Ø6 Nut M6 UNI5588 M6014206 Key DIN 6885 5x5x15 Polarity motor sticker Identification motor sticker Anti-seize Harken ® Grease Axial Threadlocker 35.2 ST E/HY Installation and Maintenance Manual Radial Winch...
Need help?
Do you have a question about the 35.2 ST E and is the answer not in the manual?
Questions and answers