1. Manuals
  2. Brands
  3. THUNDER TIGER Manuals
  4. Toy
  5. TTR4307
  6. Assembly manual

THUNDER TIGER TTR4307 Assembly Manual

Sparky arf airplane
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Distributed in North America by Ace Hobby Distributors, Inc. • 116 W 19th ST, Higginsville, MO 64037
Phone: 660-584-7121 • www.acehobby.com • E-mail: service@acehobby.com
This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.
It does not cover any damage caused by use or modification. The warranty does not extend beyond the prod-
uct itself and is limited only to the original cost of the kit. By the act of building this user-assembled kit, the
user accepts all resulting liability for damage caused by the final product.
prepared to accept this liability, it can be returned new and unused to the place of purchase for a refund.
This is not a toy. Assembly and flying of this product requires adult supervision.
Read through this book completely and become familiar with the assembly and flight of this airplane.
Inspect all parts for completeness and damage. If you encounter any problems, call 660-584-6724 for help.
Sparky ARF
Assembly Manual
Sparky ARF Airplane (TTR4307)
Warranty
Notice: Adult Supervision Required
1
Specifications:
1450mm)
Wing Span: 57"(
Wing Area:
360sq.in.(23.2dm
2
)
Length:
34"(865mm)
Weight:
1.6 lbs.(700-750g)
Motor:
400 Motor req'd
Radio:
2~3 channel
If the buyer is not
JE6454

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TTR4307 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for THUNDER TIGER TTR4307

Summary of Contents for THUNDER TIGER TTR4307

  • Page 1 Motor: 400 Motor req’d Radio: 2~3 channel Sparky ARF Airplane (TTR4307) Distributed in North America by Ace Hobby Distributors, Inc. • 116 W 19th ST, Higginsville, MO 64037 Phone: 660-584-7121 • www.acehobby.com • E-mail: service@acehobby.com Warranty This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.

  • Page 2: Pre-Assembly Notes

    Trial fit each part before gluing it in place. Make sure you are using the correct part and that it fits well before assembling. No amount of glue can make up for a poor-fitting part. ITEM NEEDED FOR COMPLETION AS6162 Motor - Thunder Tiger Electric Power System includes 400 motor, 2604AC 1:2 gear reduction set, 9 x 6 pro- Charger - Ace R/C 8.4V 60 min.

  • Page 3: Tools And Materials

    TOOLS & MATERIALS WING ASSEMBLY I. Wing Assembly Locate both wing halves and the two dihedral braces. Mix a small amount of 5-minute epoxy and glue both dihedral braces together. With the two dihedral braces together trial fit the braces in each wing half.With dihedral brace in one wing panel, trial fit it to the other wing panel, assuring no gaps from leading edge to trailing edge.

  • Page 4: Motor Installation

    FUSELAGE hold pushrod tubes in place. II. Pushrod Housing Installation III. Motor Installation A. File the motor mount at the beam as shown for better fitness. Carefully install rudder and elevator pushrod tubes; insert the ele- vator pushrod tube through the hole in the rear former through the fuselage and out the pre-drilled hole in the right of the rear cabin for- mer.
  • Page 5 STABILIZER Secure the motor tightly with enclosed Zip-Tie. place. IV. Wing Hold Down Dowel Installation V. Stab and Rudder Installation Cut away the covering film from the predrilled holes in the fuse- Center the main wing on the fuselage and attach using the rubber lage with a hobby knife.
  • Page 6 STABILIZER place with T-pins, and mark the bottom of the stab. proper alignment of stab and wing. Insert the fin into the slot in the tail and mark the fin as shown. Remove the fin and use a hobby knife and straightedge to remove the covering film from the bottom of the fin.AGAIN, BE CAREFUL NOT TO CUT TOO DEEP AS YOU MAY WEAKEN THE STABILIZER.

  • Page 7: Landing Gear Installation

    LANDING GEAR holes for the control horn using a felt marker. Using a hobby knife remove the covering over the landing gear slot. Push the landing gear down into the slot. Apply a few of drops of medium CA into the slot and slide the former into place. WARNING: WHEN YOU INSERT THE FORMER, IT WILL SQUIRT EXCESS CA OUT THE HOLES NEAR THE LANDING GEAR, SO BE CAREFUL!! J.

  • Page 8: Control Throws

    RADIO wood in place. E. Install the ESC switch VIII. Balancing Balance the plane. With the wing on the airplane, use your two index fingers to suspend the model in the air. Locate your fingers 1 Secure the mini servo in place as shown. Install the EZ connector 1/4”back from the leading edge of the wing, about 4”out from the fuse- on the servo horn.
  • Page 9 RADIO/PREFLIGHT THE DIRECTION OF MOVEMENT (RUDDER AND ELEV A TOR) NEUTRAL RIGHT TURN LEFT TURN Check the position of rudder and elevator (if these are in neutral). Set the trim in neutral position. Move the stick to the right. Move the stick to the left. Set the sticks in neutral position DOWN RIGHT AND UP...

  • Page 10: General Flying

    GENERAL FLYING transmitter first and make sure the throttle control stick or slide Please let Ace R/C and Thunder Tiger be your chosen brand, no matter throttle( ACE T3S) is at idle position. what direction you progress. XIII. Post-Flight XII. Flying...
  • Page 11 FLYING Incorrect Launch firmly into wind straight and level. Do not throw upwards or the plane will stall and crash! Wind Direction Correct Straight level with ground Example of a turn using Example of a turn using Launch only rudder rudder then elevator Wind Landing...

  • Page 12: Parts Drawings

    PARTS DRAWINGS IMPORTANT Please check the contents of your kit box with these part sketches before beginning construction. This will not only familiarize you with the parts and their names, but it will also give you a head start in the unlikely event that you are missing a part. AS6159 Wing Set Dihedral Brace (2) Wing Protector (1)

Table of Contents