Summary of Contents for Arrow Storage Products PT104
Page 1
Owner's Manual & Assembly Instructions CO01 Model No. PT104 PTG104 PT104EU PTG104EU Missing Parts, Questions on Assembly? Call: 1-800-851-1085 or assist@arrowsheds.com Do not return to dealer, they are not equipped to handle your requests. 716790118 CAUTION: SOME PARTS HAVE SHARP EDGES. CARE Storage Area: 35 Sq.
Page 2
GB: Assembly manual in additional languages available online. Scan QR code below to access. FR: Manuel de montage disponible en ligne dans d’autres langues. Pour y accéder, scannez le code QR ci-dessous. SP: Manual de montaje en idiomas adicionales disponible online. Escanee el código QR a continuación para acceder.
BEFORE YOU BEGIN..Owner's Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your building model.
Page 4
PLAN AHEAD..Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Teamwork: Whenever possible, two or more people should work together to assemble your building.
Page 5
SAFETY FIRST..Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various •Practice caution with the tools being used in pieces of your building since some contain the assembly of this building. Be familiar with sharp edges.
Page 6
CARE & MAINTENANCE..Finish: For long lasting nish, periodically clean and wax the exterior surface. Touch-up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation. Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom.
Page 7
Base ABY09 The Base For Your Building OPTION 1: Wood Platform If you decide to build your own base, be sure to select the appropriate materials. These are the recommended materials for your base: 2 x 4's (38 mm x 89 mm) Pressure Treated Lumber 5/8"...
Page 8
Anchoring Anchoring Down The Building It is important that the entire oor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring into Wood/Post: Arrow Anchoring Kit: (Model No. AK4 or 60298) Use 1/4" (6 mm) Wood Screws. There are 1/4" (6 mm) Recommended for use with any suggested base.
Page 9
Hardware ABY11 Remove from bag of screws and save for the last step 65900A 65923 #10Bx1/2" (13 mm) 65004 #8-32x3/8" (10 mm) 65103 Black Screw (8) #8Ax5/16" (8 mm) #8-32 Hex Nut (60) Bolt (60) (Packed with Screws) Screw (246) 65109 66646 #8-32 Acorn Nut (4)
Parts List ABY12 Assembly Part Part Quantity Check Key No. Number Description in Carton List 10567 Rear Wall Angle 6403 Door Track Splice 10497 Horizontal Door Brace 10574 Front Header 10557 Roof Panel 10562 Right Gable 80015 Left Gable 6892 Right Roof Trim 10558 Right Roof Panel...
Page 12
Step 1 8934 Ramp (1) Parts Needed For 9367 Front Floor Frame (2) Floor Frame Assemblies 8936 Rear Floor Frame (2) Q14 ctr 9367 The front oor frame is made up of 8934 three pieces. The rear oor frame is made up of two pieces.
Step 2 Parts Needed For 10567 Rear Wall Angle (2) Frame Assemblies 9917 Rear Wall Channel (2) ABY15 Rear Wall Channel 118 1/8" 300,0 cm 9917 The main frame pieces reinforce 9917 the walls. These pieces will later be installed in the center and at the top edge of the rear wall.
Page 14
Step 3 Parts Needed For 10571 Roof Beam (2) Roof Beam Assemblies ABY16 The roof beams support the roof 10571 panels. The roof beam is made up of two pieces overlapped at the center. 10571 Hint: These pieces are force-fitted, 119 7/8"...
Parts Needed For Step 4 6403 Door Track Splice (1) Door Track / Header 9366 Door Track (2) ABY17 10574 Header (2) Assembly NOTE: Door Track Splice (painted part) (14) 6403 The door track/header assembly supports the sliding doors and rein- forces the front wall.
Page 16
Step 5 Front Floor Assembly (1) Parts Needed For 10544 Side Floor Frame (2) Floor Frame Rear Floor Assembly (1) ABY18 RIGHT REAR 10544 STEP 10544 8936 Assemble the four corners of the oor frame using two screws at each corner as shown.
Page 17
Step 6 Parts Needed For 6515 Wall Panel (2) 9373 Front Wall Panel (2) Corners 6020 Corner Panel (4) ABY19 Narrow Side 6020 (38) Wide Side NOTE The remainder of the building assembly requires many REAR hours and more than one person. Do not continue 6020 beyond this point if you do not have enough time to complete the assembly today.
Page 18
Rear Wall Angle Assembly (1) Step 7 Parts Needed For Rear Wall Channel Assembly (1) 10545 Side Wall Channel (2) Frames 10564 Side Wall Angle (2) ABY20 Door Track/Header Assembly (1) STEP (46) The main frame pieces give rigidity to 13/16"...
Page 19
Step 8 Parts Needed For 6515 Wall Panel (2) Wall Panels ABY21 Fasten the wall panels at the top and bottom with screws. (30) Fasten the center of each panel to the wall channel with screws. Each wall panel has a crimped rib Fasten overlapping ribs as before.
Page 20
Step 9 Parts Needed For 9369 Door Jamb (2) Front Channel/Door Jamb 9365 Front Wall Channel (2) ABY22 9365 (18) The door jambs reinforce the door STEP opening and provide an attractive trim. Follow these steps for both INSIDE OF door jambs.
Page 21
Step 10 Parts Needed For Roof Beam Assembly (1) Roof Beam ABY23 The dimension stated below measures from the end of the angle towards the front of the building. Fasten the roof beam assembly, small holes on top, to the side wall angle with a bolt and nut.
Page 22
Step 11 Parts Needed For 10558 Right Roof Panel (1) Right/Left Roof Panels 80011 Left Roof Panel (1) ABY24 Position a right roof panel at the right side and fasten to the header, roof beam and rear wall angle using (18) screws as shown.
Page 23
Step 12 Parts Needed For 10557 Roof Panel (2) Roof Panel 10559 Roof Panel (1) ABY25 Screws To Rear Wall Angle (36) Install a wide roof panel 10557, narrow roof panel 10559, and Fasten At a wide roof panel 10557 in the Overlap With positions shown.
Step 13 Parts Needed For 10562 Right Gable (1) Gables 80015 Left Gable (1) ABY26 Fasten to the right roof panel, side wall angle and front header using screws, bolts and nuts as shown. (10) Repeat steps 1 and 2 for the left Position the right gable at the gable.
Step 14 Parts Needed For 6892 Right Roof Trim (2) Roof Trim 80019 Left Roof Trim (2) ABY27 Using your thumb and index nger, overbend the bottom ange of the roof trim at the corner inward enough so the right and left roof trim caps t onto right and left corners.
3719 Door Handle Brace (2) Step 15 Parts Needed For 10475 Right and Left Doors (2) Door Assembly 10497 Horizontal Door Brace (4) ABY28 6278 Vertical Door Brace (2) (12) The steps on this page tell how to assemble the right door. You will per- form exactly the same procedures for the left door.
Step 16 Parts Needed For Right Door Assembly (1) Door Installation & Adjustment Left Door Assembly (1) ABY29 Horizontal Door Brace Gable Door Track Door Slide From inside the building, put the bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the front frame track.
Page 28
PT104 PTG104 PT104EU PTG104EU CO32 Anchoring Anchor your building at this time. SOME FACTS ABOUT RUST 1. Avoid nicking or scraping the coating surface, Rusting is a natural oxidizing process that occurs inside and out. when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or 2.