Advertisement
GS1200-5HP v2 / GS1200-8HP v2
5-Port / 8-Port Web Managed
PoE Gigabit Switch
Quick Start Guide
ENGLISH | DEUTSCH | FRANÇAIS | ITALIANO
ESPAÑOL | NEDERLANDS | DANSK | NORSK
SVENSKA | SUOMI
Package Contents
Switch
Power Adapter
Power Cord
QSG
Declaration of Conformity
DoC
Safety Warning
1
Hardware Installation
2
POWER
ON
Back
DC 55V
1
Power Outlet
Front
PoE
3
4
OR
IP Phone
PoE IP Cam
Modem / Router
* Non-PoE devices can connect to the PoE ports, but PoE power
is not supplied to them.
NL
1
Sluit aan op een geschikte stroombron.
2
Zet de schakelaar op 'ON (AAN)'.
3
Sluit PoE poorten 1 - 4 aan op PoE apparaten (zoals IP
Cam en IP phone).
4
Sluit aan op een modem of router met internetverbinding.
DK
1
Tilslut til en relevant strømkilde.
Sæt strømkontakten til ON-positionen.
2
3
Tilslut PoE-port 1 - 4 til PoE-enheder (så som IP-kamera
og IP-telefon).
4
Tilslut til et modem eller router der har internetadgang.
NO
Koble til en hensiktsmessig strømkilde.
1
Sett strømbryteren i påslått posisjon.
2
Koble PoE-port 1 til 4 til PoE-enheter (for eksempel IP
3
Cam og IP-telefon).
Koble til et modem eller en ruter som har
4
Internett-tilgang.
SE
1
Anslut till en lämplig strömkälla.
2
Konfigurera strömbrytaren till påslagen position.
Anslut PoE-portar 1 - 4 till PoE-enheter (såsom IP Cam
3
och IP-telefoni).
4
Anslut till ett modem eller en router som har internetåt-
komst.
FI
1
Liitä laite yhteensopivaan virtalähteeseen.
Aseta virtakytkin ON-asentoon.
2
Liitä PoE-portit 1–4 PoE-laitteisiin, kuten IP-kameraan tai
3
IP-puhelimeen.
4
Liitä laite modeemiin tai reitittimeen, josta on
Internet-yhteys.
2
Manage Your Device
Switch IP:
192.168.1.3
5
PC IP:
192.168.1.4 ~ 192.168.1.254
6
Password : 1234
http://192.168.1.3
(default)
Log in
Password 1234
System Information
SIGN IN
NL
5
Sluit uw computer aan op de Schakelaar met een
Ethernet-kabel. Uw computer dient een IP-adres te
hebben in hetzelfde subnet als de Schakelaar.
Open uw webbrowser en ga naar http://192.168.1.3. Voer
6
1234 in als wachtwoord. Klik op AANMELDEN.
DK
5
Tilslut din computer til switchen ved brug af et
Ethernet-kabel. Din computer skal have en IP-adresse i
det samme undernet som switchen.
Start din webbrowser og gå til http://192.168.1.3. Indtast
6
1234 som adgangskode. Klik på SIGN IN (Log på).
NO
Koble datamaskinen til bryteren ved hjelp av en
5
Ethernet-kabel. Datamaskinen må ha en IP-adresse i
samme subnett som bryteren.
6
Åpne nettleseren og gå til http://192.168.1.3. Angi 1234 som
passord. Klikk på LOGG PÅ.
SE
Anslut datorn till switchen med en Ethernet-kabel. Datorn
5
måste ha en IP-adress i samma subnät som switchen.
Starta din webbläsare och gå till sidan http://192.168.1.3.
6
Skriv in 1234 som lösenord. Klicka på LOGGA IN.
FI
5
Liitä tietokone kytkimeen Ethernet-kaapelilla.
Tietokoneen IP-osoitteen on oltava samassa aliverkossa
kytkimen IP-osoitteen kanssa.
6
Avaa selain ja siirry osoitteeseen https://192.168.1.3. Kirjoita
salasanaksi 1234. Valitse SIGN IN (KIRJAUDU).
LEDs
On - Power on
PWR/SYS
Green
Blinking - Starting up
On
- 10/100 Mbps
connection ready
Amber
Blinking - Data transmitting
LINK/ACT
On
- 1000 Mbps
connection ready
Green
Blinking - Data transmitting
On - PoE enabled
PoE
Green
Off - PoE disabled or not
supplied
On - More than 50W supplied
and approaching maximum
Amber
PoE MAX
Off - Less than 50W supplied
Troubleshooting
I cannot see or access the Login screen in the Web Configurator.
Make sure you are using the correct IP address.
(The default IP address is 192.168.1.3.)
Make sure your computer is in the same subnet as the Switch. If you
haven't changed the default IP address, your computer IP address should
be in the 192.168.1.4 ~ 168.1.254 range.
Make sure you have entered the Password correctly. If you have changed
the Password and have forgotten it, you'll have to reset the Switch to its
factory default.
(The default Password is 1234.)
The PoE LED is off/PoE power is not supplied.
Make sure the Ethernet cable is securely connected to the Switch, and
you're using the correct type of Ethernet cable (Category 5e, 6UTP/STP, or
better Ethernet cable).
Go to System in the Web Configurator to check the amount of PoE power
available. The maximum PoE power is 60W, and the maximum per port is
30W. If the total power required by the PoE-enabled devices exceeds the
maximum PoE power, the last PoE-enabled device connected to the
Switch won't be powered up (PoE power is allocated in the order the
PoE-enabled devices were connected).
A loop is detected.
A loop may happen in the following example situations:
1. The Switch is connected to another device in a loop state.
2. The Switch is connected to another device with two cables.
Loop Prevention is enabled by default. If a loop happens, the Switch will
block the port in a loop state. If a loop happens on two ports, the Switch
will block the higher-numbered port. For example, if a loop happens on
ports 4 and 5, the Switch will block port 5, and its LED will be off. To restore
a port in a loop state, disconnect it, check the network connections, and
reconnect it.
You can log into the Web Configurator. Go to System in the Web
Configurator to check your port status.
Support Information
Netherlands
Finland
+31 (0)88-00029112
+ 358 9 4780 8400
support@zyxel.nl
teknisk@zyxel.fi
Denmark
+ 45 30 55 07 00
support@zyxel.dk
Norway
+ 47 22 80 61 80
teknisk@zyxel.no
Sweden
+ 46 8 557 760 60
support@zyxel.se
See the User's Guide at www.zyxel.com
for more information, including customer
support and safety warnings.
EU Importer
Zyxel Communications A/S
Generatorvej 8D, 2860 Søborg, Denmark.
http://www.zyxel.dk
US Importer
Zyxel Communications, Inc
1130 North Miller Street Anaheim, CA 92806-2001
http://www.us.zyxel.com
Copyright © 2017 Zyxel Communications Corp. All Rights Reserved.
Advertisement
