Advertisement
Command
AT + CRC = [n]
Specifies whether to use result codes of "+CRING:type" for incoming calls.
n = 0: Does not use the result code of "+CRING:type". (default and when parameter omitted)
n = 1: Uses the result code of "CRING:type". The example of codes are as follows:
*1, *2
ex. Enter
AT + CREG = [n]
Specifies whether to show the "inside/outside the service area" information.
n = 0: Does not show the information. (default and when parameter omitted)
n = 1: Shows the information.
If you enter "AT + CREG?", it shows the information in the format of " + CREG:n,stat".
*1, *2
ex. Enter
AT + GMI
Shows the manufacturer's name of FOMA terminal.
ex. Enter
AT + GMM
Shows FOMA terminal name.
ex. Enter
AT + GMR
Shows the version of FOMA terminal.
ex. Enter
AT + IFC = [n,[m]]
Specifies the local flow control between the PC and FOMA terminal.
n is for setting the DCE-by-DTE control.
m is for setting the DTE-by-DCE control. If you omit this parameter, the same value as DCE-by-DTE is
assumed.
If you omit both parameters, "AT+IFC = 2, 2" is assumed.
*1, *2
ex. Enter
AT+WS46= [22]
Specifies the radio network FOMA terminal uses to originate a call.
*1, *2
ex. Enter
ATA
Specifies how to handle incoming packet or 64K data communications. For incoming packet
communications, you can specify the following:
ATA184: Receives an incoming call without the caller ID displayed
ATA186: Receives an incoming call with the caller ID displayed
ex. Enter
A/
Reexecutes the previous command.
ex. Enter
ATD
Originates a packet or 64K data communication.
・Packet communication: Enter in the format of "ATD ＊ 99 ＊＊＊ cid#". If you omit cid parameter,
・64K data communication: Enter it in the format of "ATD phone-number".
・Redialing: Enter in the format of "ATDL" or "ATDN".
ex. Enter
ATE [n]
Echoes back the characters sent from the PC.
n = 0: Gives no echo back. (when parameter omitted)
n = 1: Gives echo back. (default)
*1, *2
ex. Enter
ATH
Disconnects communication.
ex. Enter
ATI [n]
Shows the identification code.
n = 0:Shows "NTT DoCoMo". (when parameter omitted)
n = 1:Shows model name of FOMA terminal. n = 2:Shows the version of FOMA terminal.
ex. Enter
ATO
Switched the mode from the online command to the online data.
ex. Enter
ATQ [n]
Specifies whether to show the result code on the PC.
n = 0: Shows the result code. (default and when parameter omitted)
n = 1: Does not show the result code.
*1, *2
ex. Enter
Packet communication ... +CRING:GPRS "PPP"... "mopera.net"
64K data communication... +CRING:SYNC
AT + CRC = 0
stat=0: Outside the service area stat = 1: Inside the service area (home) stat = 4: Unknown
stat = 5: Inside the service area (visitor)
AT + CREG = 0
AT + GMI
AT + GMM
AT + GMR
n = 0: Does not use the flow control. n=1: Uses XON/XOFF flow control.
n = 2: Uses RS/CS (RTS/CTS) flow control. (default)
m = 0: Does not use the flow control. m = 1: Uses XON/XOFF flow control.
m = 2: Uses RS/CS (RTS/CTS) flow control. (default)
AT + IFC = 2,2
AT + WS46 = 22
ATA
A/
"cid = 1" is assumed.
When you enter it in the format starting with "ATD184 ＊ 99", 184 (hide caller ID) is attached to the call
outgoing to the APN specified with cid parameter (186 (show caller ID) is treated in the same manner).
ATD phone-number
ATE0
ATH
ATI0
ATO
ATQ0
Description & Parameter
AT + CRC?
Display
AT + CREG?
Display
Display
None
Display
None
Display
None
AT + IFC?
Display
AT + WS46?
Display
Display
None
Display
None
Display
None
Display
None
Display
None
Display
None
Display
None
Display
None
28
AT + CRC = ?
Test
AT + CREG = ?
Test
AT + GMI = ?
Test
AT + GMM = ?
Test
AT + GMR = ?
Test
AT + IFC = ?
Test
AT + WS46 = ?
Test
Test
None
Test
None
Test
None
Test
None
Test
None
Test
None
Test
None
Test
None
Next
Advertisement
