Advertisement
･
For the dialup connection (APN), inquire your
provider or network administrator.
･
The dialup connection settings can be considered
as phonebook registration for packet
communication. The comparison between dialup
connection settings and the FOMA terminal
phonebook entries is as follows:
Dialup connection
settings
Registration
Registration number
number (cid)
(Phonebook No.)
APN
Party's phone number
･
The registered cid become the connection
numbers of dialup connection setting.
Setting to show/hide caller ID
Take care when disclosing your caller ID since it is
important information.
･
Settings must be "show" for using mopera U /
mopera.
Default not set
Example
For Windows XP
1
Perform Steps 1 to 5 of "Setting the dialup
connection (APN) for packet
communication" ☛P15
2
Set to show (186)/hide (184) caller ID
during packet communication
Enter in the format "AT ＊ DGPIR=<n>".
AT ＊ DGPIR = 1
When packet communication connection is
being established, "184" is added to connect
to the dialup connection (APN).
AT ＊ DGPIR = 2
When packet communication connection is
being established, "186" is added to connect
to the dialup connection (APN).
■
When nothing is displayed even if AT
command is entered: ATE1
･
For details ☛P28
3
Check that OK is displayed and click
イル
ハイパーターミナルの終了
and
･
現在、接続されています。切断してもよ
After
ろしいですか？
appears, click
･
と名前付けされた接続を保存しますか
"XXX"
いいえ
appears. Click
■ Setting to show/hide caller ID by dialup
network settings
FOMA terminal phonebook
entries
ファ
はい
.
The dialup network settings can also be used to
append "186 (show)" or "184 (hide)" to the dialup
connection number.
If "186" (show) or "184" (hide) is set by both the
AT ＊ DGPIR command and dialup network
settings, the show/hide caller ID setting is as
follows:
Setting made by
AT ＊ DGPIR
command
Dialup network
setting (<cid>=3)
＊ 99 ＊＊＊ 3#
184 ＊ 99 ＊＊＊ 3#
186 ＊ 99 ＊＊＊ 3#
･
To reset the show/hide setting made by the AT ＊
DGPIR command to the default (not set), enter "AT
＊ DGPIR = 0".
Setting for Windows XP
Setting the dialup connection
スタート
1
Click
クセサリ
通信
,
ネットワーク接続
The
2
新しい接続を作成する
Click
connection) in
(Network task)
新しい接続ウィザード
The
wizard) screen appears.
次へ
3
Click
A screen for selecting the type of network
connection appears.
インターネットに接続する
4
Select
(Connect to Internet)
The setup screen appears.
5
接続を手動でセットアップする
Select
(Set up connection manually)
The Internet connection screen appears.
?
6
Select
ダイヤルアップモデムを使用して
接続する
(Use dialup modem to connect)
z
次へ
Click
The device selection screen appears.
･
If there is only one modem installed, the device
selection screen is not displayed. Go to Step 8.
17
Not set
Hide
Show
Caller ID
Caller ID
Caller ID
is sent.
is not
is sent.
sent.
Caller ID is not sent.
Caller ID is sent.
すべてのプログラム
,
ネットワーク接続
and
screen appears.
(Create new
ネットワークタスク
(New connection
z
次へ
Click
z
Click
Next
ア
,
次へ
Advertisement
