Related Manuals for Wieland wienetUMS 8-4POE-W
Summary of Contents for Wieland wienetUMS 8-4POE-W
-
Page 1: User Manual
wienet UMS 8-4POE-W Ethernet switch USER MANUAL Doc.-No. BA001106 Updatet: 01/2017 (Rev. A) -
Page 2: About This Manual
COPYRIGHT This document is copyright-protected. The rights derived from this copyright are reserved for Wieland Electric GmbH. Reproduction of this document or parts of this document is only permissible within the limits of the statutory pro- vision of the Copyright Act. Any modification or abridgment of the document is prohibited without the express written agreement of Wieland Electric GmbH. -
Page 3: Table Of Contents
Wiring the power outputs ................ 14 Technical Parameters ................. 15 Basic parameters ....................15 Standards and regulations ................... 16 Troubleshooting ..................16 Diagnosis with LED Indicators ................16 FAQ troubleshooting .................... 16 Recommended Literature ................16 Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 4: About This Manual
"Danger" or "Warning" are strictly used for cases which present a risk to life or limb. Damage to property only falls into these categories if there is also a risk of personal injury that corresponds to these levels. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 5: Product Disposal Instructions
At the end of it’s life this product MUST NOT be mixed with other commercial waste for disposal. Check the terms and conditions of your supplier for disposal information. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 6: Switch Description
Further, wienet UMS 8-4POE-W provides current overload protection with a resettable fuse to ensure that the device component won’t be dam- aged by overload current. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 7: Wide Operating Temperature
• 2 x Wall Mounting Bracket and Screws • 1 x DIN-rail Mounting Bracket and Screws (preassembled) • 1 x Installation instructions 5 Switch Design Basic dimensions of the switch box UMS 8-4POE-W Dimensions wienet Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 8: Ordering Code
For correct function of the switch we recommend to use it in a switch-board with earth-bonding distri- bution frame for grounding of the power supply, of the switch, the data cables and the antenna. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 9: Mounting And Demounting On A Din Rail
1. Switch off the power supply. 2. Lightly push the switch down and tilt the lower part of the switch away from the DIN-Rail. 3. Pull the device upwards off the DIN-Rail. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 10: Mounting On A Wall
1. Screw the L profiles to the top and bottom of the switch using the included screws. 2. Screw the switch to the wall. Please note the hole dimensions given below. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 11: Description Of The Front-Panel
POE power + (if POE is equipped) POE power + (if POE is equipped) RXD- Receive Data – negative pole Input/Output POE power - (if POE is equipped) POE power - (if POE is equipped) Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 12: Network Connection
MDI port.The switch supports auto-crossover to make networking more easy and flexible. You can connect any RJ-45 (MDI-X) station port on the switch to any device such as a switch, bridge or switch. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 13: Power Connection
Do not bundle together wiring with similar electrical characteristics. • Make sure to separate input and output wiring. • Label all wiring and cabling to the various devices for more effective management and servicing. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 14: Wiring The Power Outputs
8. Tighten the screws on the terminal block to secure it to the terminal block receptor. If there is no gap between the terminal block and the terminal receptor, the termi- nal block is seated correctly. Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 15: Technical Parameters
0.5 Nm max.(5.6 lbf-in) max. Norms and approvals FCC Part 15, Subpart B, Class A Emission: EN55011, EN55022 Class A; EN55024 Immunity: EN61000-6-4, EN61000-6-2, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN6000-4-8, Approval cULus (UL508) Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017... -
Page 16: Standards And Regulations
The transmission of data packets doesn’t work although the LED indicators are normal and the connected cables are correct. • Check your system's ethernet devices, their status and the network or device configuration. 8 Recommended Literature Wieland Electric: Installation instructions, Wieland Electric GmbH | BA001106 (Rev. A) | 01/2017...
Need help?
Do you have a question about the wienetUMS 8-4POE-W and is the answer not in the manual?
Questions and answers