Display; Parameter Tables - Resource Data Management PR0712-EPR Installation & User Manual

Mercury 2 & Intuitive Mercury EPR Stepper Installation Guide

Display

From the function menu scroll to and select diSP.
Press enter and one of the following values will be shown: -
0. Controller display will show the whole number and tenths value of a temperature reading. (Default)
1. Controller display will show temperatures as a whole number.

Parameter Tables

Not all parameters apply to all controller types, for example P-83 is Fan Control which only applies to coldroom types 5 & 6, this
parameter will not appear if the controller is set up as a type 3 or 4 case types. In the following table, the type columns on the right hand
side will be greyed out if that parameter does not apply to that controller type.
Number Parameter
P-01 Cut-in Temp.
P-02 Diff.
P-03 Control Weight
P-04 Display Weight
P-09 Response On
P-10 Response Off
P-51 EEV Minimum Opening
P-56 EEV Start Opening
P-55 Average Valve Opening
P-57 EEV Divide Value
P-12 Relay 3 Mode
P-85 Key-switch Mode
P-87 Control Probe type
P-90 Resistor Case Off
P-92 Fans temperature mode
P-93 Fans Off Temperature
P-83 Fan Control
P-78 Fan Pulse On
P-79 Fan Pulse Off
P-15 Probe 5 Select
P-16 Relay 2 Mode
P-17 Evap. Select
P-97 Control Fail Valve Level
P-29 Probe 1 Resistor Function
P-18 Service Interval time
P-19 Switch Resistors
P-98 Lights Case Off
P-30 Valve Type
P-31 Step Max
P-32 Step Close
P-33 Step Speed
P-34 mA Peak
P-35 Half Step
P-36 mA Hold Current
P-37 Shut Speed
P-06 Shut Enable
P-07 Shut Time
P-05 Overdrive Time
P-77 Man Stop Valve/Fans
P-39 Stepper In Case Off
P-20 Alarm Delay
P-21 UT Alarm
P-22 OT Alarm
P-23 Log Probe Type
P-24 Slug Log Probe
Warning
Ensure that all power is
switched off before
installing or maintaining
this product
Please Note
Range
o o
C ( F )
-42 to 30 (-43.6 to 86)
0 to 10 (0 to 18)
0 to 100
0 to 100
1 to 30
1 to 30
0 - 100%
0 - 100%
0 - 100%
0 - 100%
0 = Suction Line, 1 = Defrost Valve
0 = Case, 1 = Fans only, 2 = toggle, key
off
0 = Use Air on Probe,
1 = Use Log Probe
0 (Disabled),1(Enabled)
0 = Off, 1 = Temperature,
2 = Over-temperature, 3 = Temp/OT
-42 to 30 (-43.6 to 86)
0 = Off, 1 = Run, 2 = Pulse
00:00 to 99:00
00:00 to 99:00
0 = Defrost, 1 = Monitor
0 = Lights, 1 = Alarm
0 = Local, 1 = Rem1, 2 = Rem2,
3 = Rem3, 4 = IoBrd
0 to 100%
0 = Plant fault, 1 = External defrost
0 to128
0 (Off), 1 (On)
0 (Off), 1 (On), 2 (Unused)
0=Carel, 1=Sporlan1, 2=Sporlan2
3=Alco, 4=Other*
0 to 6800 See: Valve type
0 to 6800 See: Valve type
0 to 6800 See: Valve type
0 to 500 See: Valve Type
0 (Off),1 (On) See: Valve Type
0 to 500
0 to 6800
0 (Off), 1 (On)
00:00 to 99:00
1 to 25
0 (Off),1 (On)
0 (Off),1 (On)
00:00 to 99:00
-49 to 60 (-56.2 to 140)
-49 to 60 (-56.2 to 140)
0 (Off), 1 (Logging), 2 (Logging/Alarm)
0 (Off), 1 (On)
Revision 1.2a
Step Units Default LT
o o
C ( F )
0.1 Deg -20 (-4)
0.1 Deg 2 (3.6)
1 % 50
1 % 50
1 10
1 10
1 % 10
1 % 10
1 % 100
1 50
1 1
1 3
1 0
0
1 0
0.1 Deg -10 (14)
1 1
01:00 mm:ss 05:00
01:00 mm:ss 30:00
1 0
1 0
1 0
0.1 % 0
1 0
1 KHrs 60
1
0
1 --- 0
1 --- 480
1 --- 500
1 Hz 50
1 mA 450
1 --- 0
1 0
1 Hz 50
1 0
01:00 mm:ss 04:00
1 hours 8
1 0
1 1
01:00 mm:ss 20:00
0.1 Deg -30 (-22)
0.1 Deg -15 (5)
Off
Off
www.resourcedm.com
Default HT Type Type
o o
C ( F ) 3&4 5&6
 
0.0 (32)
 
1.5 (2.7)
 
50
 
50
 
10
 
10
 
10
 
10
 
100
 
50
 
1
 
3
 
0
 
0
 
0
 
8 (46.4)

1

05:00

30:00
 
0
 
0
 
0
 
0
 
0
 
60
 
1

0
 
0
 
480
 
500
 
50
 
450
 
0
 
0
 
50
 
0
 
04:00
 
8
 
0
 
1
 
20:00
 
-2 (28.4)
 
5 (41)
 
Off
 
Off
Page 10 of 25