STAINLESSLITE PLUS UNVENTED MAINS PRESSURE HOT WATER STORAGE INSTRUCTION MANUAL DESIGN, INSTALLATION & SERVICING ONE NAME. EVERY SOLUTION. WWW.GLEDHILL.NET...
Page 2
In the interest of continuously improving the StainlessLite Plus additional expansion vessel must be fitted to accommodate the extra expansion updated at each service. range, Gledhill Building Products Limited reserve the right to modify the product volume. 7. Check the water pressure downstream of the...
Page 3
DESIGN DESIGN Figure 1 Figure 2 Figure 3 Figure 4 StainlessLite Plus Direct Solar StainlessLite Plus is a range of unvented hot water storage cylinders, manufactured in the latest high quality duplex stainless steel. They StainlessLite Plus Direct Solar is an electrically are designed to provide mains pressure hot heated, unvented hot water storage cylinder water and are supplied as a package which...
DESIGN DESIGN Direct Solar Direct NOTES 1. Not all models - see table 1. 2. Recovery times based on Primary Coil/I.H. duty (ie. assumes the boiler output is adequate). 3. All connections are supplied with compression fittings for direct connection to copper pipework. 4.
Page 5
DESIGN DESIGN Indirect Solar Indirect NOTES 1. Not all models - see table 2. 2. Recovery times based on Primary Coil/I.H. duty (ie. assumes the boiler output is adequate). 3. All connections are supplied with compression fittings for direct connection to copper pipework. 4.
DESIGN DESIGN StainlessLite Plus Direct StainlessLite Plus Direct Solar Basic Appliance Basic Appliance 1. Hot water draw off (22mm) compression 1. Hot water draw off (22mm) compression 2. Pressure and temperature relief valve 2. Lift up temperature & pressure relief valve 89-96°/6 bar 89-96°/6 bar 3.
INSTALLATION INSTALLATION General Design Considerations General Restrictions Pipe Layout Insulation of pipework Pipe outside Maximum The cupboard footprint needs to be at least 650mm square for standard units up to a. The highest hot or cold water draw off point should not exceed 10 metres above In all mains pressure installations it is important diameter heat loss...
Page 8
Gledhill Building Products Limited are used. All parts are available to The example below is for G1/2 temperature relief valve with a discharge pipe (D2)
Page 9
INSTALLATION INSTALLATION The immersion thermostat has two terminals Heating/primary Systems Schematic Open Vented Primary System A and B. The Live (brown) wire should be connected to terminal A and the Neutral (blue) The boiler and primary/heating systems should Warming/Overflow wire should be connected to terminal B. It has be sized and installed in accordance with BS Pipe been our experience that Crimp terminals make...
Page 10
(or in the flow vessel. Mains CW in Motorised Valve pipe immediately adjacent to the collector), If this arrangement is used then the Gledhill Energy cut-out will provide the information required by the warrant will not be valid. (Not supplied) solar controller.
Page 11
INSTALLATION INSTALLATION Schematic Showing Solar Wiring Requirements (S-PLAN) WIRING DIAGRAM WITH TWO 2 PORT VALVES AND BOILER CONTROLLED PUMP OVERRUN OPTION WIRE COLOUR LEGEND Central Heating Control Room Thermostat Dual Cylinder Stat S1 S1 Spade connectors Blue Overheat Stat Control Stat required for earth Brown...
Warranty IMPORTANT - DRAIN DOWN PROCEDURE conditions offered by Gledhill. 1 Switch off both the boiler and the immersion heater 2 Open the nearest hot tap and run all hot water until cold, then close it...
Reducing Valve is at fault and the Gledhill approved replacement should be fitted. Checklist located on the inside back pages of this document. If the pressure is correct then the Relief Valve will require replacing with a Gledhill approved component.
Page 14
SERVICING AND MAINTENANCE SERVICING AND MAINTENANCE FAULT - No Hot Water (Direct) FAULT - Poor Water Flow at Hot Taps START START Is incoming mains supply Water service check by Is power on to elements? Switch on flow/pressure adequate? supply company required Is in-line strainer Clean or replace strainer Is control temperature...
SERVICING AND MAINTENANCE APPENDIX Water Savings SPARE PARTS LIST Water Related Costs Can Be Reduced By Good Plumbing Practice Description Quantity Stock Code No. 3kW immersion element SH010 22mm 90° compression elbow c/w/drain SF003 Lift up pressure and temperature relief valve 6 bar 92-95°C SG023 Inlet group set at 3 bar c/w expansion relief valve set at 4.5 bar SG022...
• No factory fitted parts have been removed for unauthorised repair or replacement and the product has not been modified - other than by Gledhill. you intend to take that it is clear of •...
MUST NOT BE REMOVED OR ALTERED IN ANY WAY OR THE GUARANTEE WILL NOT BE VALID. GLEDHILL WILL (i) economic loss which shall include loss of in the event that the Purchaser shall sell any of the goods pursuant to clause (6) hereof, the Purchaser shall...
Page 18
demonstrating compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference. Failure to install and commission this equipment to the manufacturer’s instructions may invalidate the warranty but does not affect statutory rights. MAINS PRESSURE HOT WATER STORAGE SYSTEM COMMISSIONING CHECKLIST SERVICE RECORD Customer name: Telephone number:...
T: 01253 474550 enquiries@gledhill.net WWW.GLEDHILL.NET Due to a programme of continuous improvement Gledhill Building Products reserve the right to modify products without prior notice. It is advisable to check the product technical detail by using the latest design and installation manuals available from our technical support team or on our website.It is an offence...
Need help?
Do you have a question about the StainlessLite Plus Direct D90 and is the answer not in the manual?
Questions and answers