Warranty Information - gledhill StainlessLite Plus Direct D90 Instruction Manual

APPENDIX
MANUAL HANDLING OF APPLIANCE PRODUCTS
Description
Manual handling means any transporting or supporting of a load (including lifting,
putting down, pushing, pulling, carrying or moving) by hand or bodily force.
Scope
This assessment will cover the largest unit within each product range.
For specific weights and dimensions please refer to technical data section.
Main Hazards
Vision may not be clear due to the size of the products.
Adopting an incorrect method of lifting may cause injury, attempting to lift these
products will require help from others. (Team lifts)
Control Measures
Manual lifting procedure
The lift, key factors in safe lifting are:
a. Balance
Position of back
b.
c. Positioning of the arms and body
d. The hold
e. Taking the lead for team lifts
Balance - Since balance depends essentially upon the position of the feet,
a.
they should be apart about hip breadth with one foot advanced giving full
balance sideways and forward without tension. In taking up this position,
lifting is done by bending at the knees instead of the hips and the muscles
that are brought into use are those of the thigh and not the back.
b. Position of back - Straight - not necessary vertical. The spine must be
kept rigid, this coupled with a bent knee position, allows the centre line of
gravity of the body to be over the weight so reducing strain.
c. Positioning of arms and body - The further arms are away from the side,
the greater the strain on the shoulders, chest and back. Keep elbows close
to the body arms should be straight.
d. The hold - Before lifting ensure you have a good hold.
APPENDIX B
e. Taking the lead for team lifts- As
more than one person is required
for these products ensure that one
person is taking the lead. This may
be you so ensure that each person
that is helping is made aware of the
weight and of the items listed within
this assessment. Make sure you and
any others helping know the route
you intend to take that it is clear of
any obstructions. Never jerk the load
as this will add a little extra force and
can cause severe strain to the arms,
back and shoulders. If there are steps
involved decide on where you will
stop and take a rest period. Move
smoothly and in unison taking care
to look and listen to others helping
with the lift. Where possible use
a sack truck to move the product
over long flat distances, only lift the
products when necessary. If in doubt
stop and get more help.
Individual capability
Individual capability plays an important
part in handling these products. Persons
above average build and strength will
find it easier and should be in good
health. Persons below average build and
strength may require more rest periods
during the handling process.
Pregnant women should not carry out
this operation.
Persons who are not in good health
should seek medical advice prior to
commencing any lifting or manual
handling operation.
Residual risk
Following the guidelines given above will
reduce any risk to injury.
All persons carrying out this operation
must be fully trained and copies of the
specific risk assessment made available
for inspection and use in their training
process.
Further guidance on Manual Handling
can be obtained from the Health and
Safety Executive. Manual Handling
Operations Regulations 1992 (amended
by Health and Safety (Miscellaneous
Amendments) Regulations 2002.
Page 30

WARRANTY INFORMATION

Gledhill Building Products guarantees the StainlessLite Plus cylinder and
components against material defect or manufacturing fault for a period of two
years from the date of purchase. The two year warranty on the stainless steel
inner cylinder will be extended to twenty five years in domestic properties on the
registration of the cylinder (see documentation enclosed with the unit).
The above product guarantees are valid provided:
• It has been installed by a competent installer in accordance with the instructions
detailed in our installation manual and all relevant Codes of Practice and
Regulations in force at the time of installation.
• No factory fitted parts have been removed for unauthorised repair or replacement
and the product has not been modified - other than by Gledhill.
• Any replacement parts used should be authorised, approved Gledhill spare parts.
• The cylinder has only been used for the storage of potable water supplied for the
public mains (-max 200mg/litre chloride).
• It has not been subject to wrong or improper use, left uncared for, or subjected to
scale or frost damage.
• The unit has been serviced annually by a competent, licenced engineer in
accordance with the requirement set out in the manual.
• The Benchmark TM Commissioning Checklist Service Record included in our manual
has been completed and updated after each annual service.
• Any disinfection has been carried out strictly in accordance with BS6700.
• For heavy use installation where constant usage / reheat is required titanium
immersion heaters should be fitted.
• The registration document enclosed with the unit is completed and returned
within 30 days of purchase by the owner. Evidence of purchase and date of supply
must be submitted upon making a claim.
Guidance in the event of a problem with the StainlessLite Plus
Your cylinder is supported by a large nationwide team of directly employed engineers,
and our call centre is able to provide technical advice throughout the year. If you have a
problem during the guarantee period, please call Gledhill Technical.
Our warranty is valid providing that;
• All the above guarantee conditions are met
• Copy of the completed annual service record and commissioning checklist is
available for inspection
As a HWA Charter Member we endeavour to provide consumers quality assurance,
product satisfaction, and confidence in Gledhill, that we will deliver a service
beyond just supplying the product.
WARRANTY INFORMATION
Page 31