Endress+Hauser Proline Promag L 400 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Endress+Hauser Manuals
  4. Measuring Instruments
  5. Proline Promag L 400
  6. Operating instructions manual
Endress+Hauser Proline Promag L 400 Operating Instructions Manual

Endress+Hauser Proline Promag L 400 Operating Instructions Manual

Hart electromagnetic flowmeter
Hide thumbs Also See for Proline Promag L 400:
Table of Contents

Advertisement

Quick Links

BA01062D/06/EN/02.13
71218251
Valid as of version
01.00.zz (Device firmware)
Products

Operating Instructions

Proline Promag L 400
HART
Electromagnetic flowmeter
Solutions
Services

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Proline Promag L 400 and is the answer not in the manual?

Questions and answers

Related Manuals for Endress+Hauser Proline Promag L 400

Summary of Contents for Endress+Hauser Proline Promag L 400

  • Page 1: Operating Instructions

    Products Solutions Services BA01062D/06/EN/02.13 71218251 Valid as of version 01.00.zz (Device firmware) Operating Instructions Proline Promag L 400 HART Electromagnetic flowmeter...
  • Page 2 • The manufacturer reserves the right to modify technical data without prior notice. Your Endress+Hauser Sales Center will supply you with current information and updates to these Instructions. Endress+Hauser...

  • Page 3: Table Of Contents

    Proline Promag L 400 HART Table of contents Table of contents 6.2.2 Preparing the measuring device ..24 Document information ....6 6.2.3 Mounting the sensor .
  • Page 4 ..... . . 100 13.3 Endress+Hauser services ....128 Operation .
  • Page 5 Proline Promag L 400 HART Table of contents 14.5 Disposal ......14.5.1 Removing the measuring device ..129 14.5.2 Disposing of the measuring device .

  • Page 6: Document Information

    Document information Proline Promag L 400 HART Document information Document function These Operating Instructions contain all the information that is required in various phases of the life cycle of the device: from product identification, incoming acceptance and storage, to mounting, connection, operation and commissioning through to troubleshooting, maintenance and disposal.

  • Page 7: Tool Symbols

    Proline Promag L 400 HART Document information 1.2.3 Tool symbols Symbol Meaning Torx screwdriver A0013442 Phillips head screwdriver A0011219 Open-ended wrench A0011222 1.2.4 Symbols for certain types of information Symbol Meaning Allowed Indicates procedures, processes or actions that are allowed.

  • Page 8: Documentation

    The following document types are available: • On the CD-ROM supplied with the device • In the Download Area of the Endress+Hauser Internet site: www.endress.com → Download For a detailed list of the individual documents along with the documentation code (→...

  • Page 9: Basic Safety Instructions

    ‣ Observe the specified pressure and temperature range. Verification for borderline cases: ‣ For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in verifying the corrosion resistance of fluid-wetted materials, but does not accept any Endress+Hauser...

  • Page 10: Workplace Safety

    If a plastic transmitter housing is permanently exposed to certain steam and air mixtures, this can damage the housing. ‣ If you are unsure, please contact your Endress+Hauser Sales Center for clarification. ‣ If used in an approval-related area, observe the information on the nameplate.

  • Page 11: It Security

    IT security measures in line with operators' security standards and designed to provide additional protection for the device and device data transfer must be implemented by the operators themselves. Endress+Hauser can be contacted to provide support in performing this task. Endress+Hauser...

  • Page 12: Product Description

    Product description Proline Promag L 400 HART Product description Product design A0017218  1 Important components of the compact version Display module Smart sensor electronics module HistoROM DAT (plug-in memory) Main electronics module Terminals (screw terminals, some available as plug-in terminals)

  • Page 13: Identification

    Proline Promag L 400 HART Incoming acceptance and product identification Incoming acceptance and product identification Incoming acceptance A0015502 A0013843 Is the order code on the delivery note (1) identical to the order code on the product sticker (2)? A0013695 A0015502...

  • Page 14: Product Identification

    Incoming acceptance and product identification Proline Promag L 400 HART If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center. Product identification The following options are available for identification of the measuring device: • Nameplate specifications • Order code with breakdown of the device features on the delivery note •...

  • Page 15: Sensor Nameplate

    Proline Promag L 400 HART Incoming acceptance and product identification 4.2.2 Sensor nameplate Order Code: Ser.No.: Ext. ord. cd.: Material: Patents Date: A0017186  3 Example of sensor nameplate Name of the sensor Manufacturing location Order code Serial number (Ser. no.) Extended order code (Ext.

  • Page 16: Symbols On Measuring Device

    Incoming acceptance and product identification Proline Promag L 400 HART 4.2.3 Symbols on measuring device Symbol Meaning WARNING!  This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious or fatal injury. Reference to documentation Refers to the corresponding device documentation.

  • Page 17: Storage And Transport

    Proline Promag L 400 HART Storage and transport Storage and transport Storage conditions Observe the following notes for storage: • Store in the original packaging to ensure protection from shock. • Do not remove protective covers or protective caps installed on process connections.

  • Page 18: For Measuring Devices ≥ Dn 350 (14")

    Storage and transport Proline Promag L 400 HART 5.2.2 For measuring devices ≥ DN 350 (14") Also observe the following notes during transport: • Lift the measuring device by the flange using the metal brackets. • If transporting by forklift, do not lift the sensor by the metal casing. This would buckle the casing and damage the internal magnetic coils.

  • Page 19: Installation

    Proline Promag L 400 HART Installation Installation Installation conditions No special measures such as supports are necessary. External forces are absorbed by the construction of the device. 6.1.1 Mounting position Mounting location Preferably install the sensor in an ascending pipe, and ensure a sufficient distance to the next pipe elbow: h ≥...
  • Page 20 Installation Proline Promag L 400 HART Installation in partially filled pipes A partially filled pipe with a gradient necessitates a drain-type configuration. The empty pipe detection (EPD) function offers additional protection by detecting empty or partially filled pipes. • Do not install the sensor at the lowest point in the drain: risk of solids accumulating.
  • Page 21 Proline Promag L 400 HART Installation A0015591 Horizontal The measuring electrode plane must be horizontal. This prevents brief insulation of the two measuring electrodes by entrained air bubbles. With horizontal orientation, empty pipe detection only works if the transmitter housing is pointing upwards as otherwise there is no guarantee that the empty pipe detection function will actually respond to a partially filled or empty measuring tube.

  • Page 22: Requirements From Environment And Process

    • Avoid direct exposure to weather conditions. • Protect the display against impact. • Protect the display from abrasion by sand in desert areas. A display protector can be ordered from Endress+Hauser: "Accessories" section (→  131) System pressure • Never install the sensor on the pump suction side in order to avoid the risk of low pressure, and thus damage to the liner.

  • Page 23: Special Mounting Instructions

    Proline Promag L 400 HART Installation A0016266  6 Measures to prevent vibration of the device > 10 m (33 ft) Adapters Suitable adapters to DIN EN 545 (double-flange reducers) can be used to install the sensor in larger-diameter pipes. The resultant increase in the rate of flow improves measuring accuracy with very slow-moving fluids.

  • Page 24: Mounting The Measuring Device

    Installation Proline Promag L 400 HART Mounting the measuring device 6.2.1 Required tools For transmitter • Torque wrench • For wall mounting: Open-ended wrench for hexagonal screw max. M5 • For pipe mounting: – Open-ended wrench AF 8 – Phillips head screwdriver PH 2 •...
  • Page 25 Proline Promag L 400 HART Installation Mounting the seals CAUTION An electrically conductive layer could form on the inside of the measuring tube! Risk of measuring signal short circuit. ‣ Do not use electrically conductive sealing compounds such as graphite.
  • Page 26 Installation Proline Promag L 400 HART Nominal Pressure rating Threaded Max. screw tightening torque [Nm] diameter fasteners [mm] [bar] [mm] Hard rubber Polyurethane PTFE PN 10 20 × M27 – PN 16 20 × M33 – PN 6 24 × M24 –...
  • Page 27 Proline Promag L 400 HART Installation Nominal diameter Threaded fasteners Max. screw tightening torque [Nm] ([lbf · ft]) [mm] [in] [in] Hard rubber Polyurethane PTFE 8 × 5/8 – 20 (15) 44 (32) 8 × ¾ – 45 (33) 90 (66) 8 ×...

  • Page 28: Mounting The Transmitter Of The Remote Version

    Installation Proline Promag L 400 HART Nominal diameter Threaded fasteners Max. screw tightening torque [Nm] [mm] [mm] Hard rubber Polyurethane PTFE 1 000 24 × M30 – – 1 200 32 × M30 – – Screw tightening torques for AS 4087, PN 16...
  • Page 29 Proline Promag L 400 HART Installation Wall mounting 17 (0.67) 14 (0.55) 5.8 (0.23) 5.8 (0.23) mm (in) 149 (5.85) A0020523 1. Drill the holes. 2. Insert wall plugs into the drilled holes. 3. Screw in the securing screws slightly at first.

  • Page 30: Turning The Transmitter Housing

    Installation Proline Promag L 400 HART A separate mounting kit can be ordered from Endress+Hauser for pipe mounting (→  131). 6.2.5 Turning the transmitter housing To provide easier access to the display module in the compact device version, the...

  • Page 31: Turning The Display Module

    Proline Promag L 400 HART Installation 4 mm A0021605 1. Loosen the fixing screws of the housing cover. 2. Open the housing cover. 3. Unlock the display module. 4. Remove the display module. 5. Loosen the fixing screws of the smart sensor electronics module.

  • Page 32: Post-Installation Check

    Installation Proline Promag L 400 HART TX 20 A0021617 1. Loosen the fixing screws of the housing cover. 2. Open the housing cover. 3. Unlock the display module. 4. Pull out the display module and turn it to the desired position in increments of 90°.

  • Page 33: Electrical Connection

    Proline Promag L 400 HART Electrical connection Electrical connection The measuring device does not have an internal circuit breaker. For this reason, assign the measuring device a switch or power-circuit breaker so that the power supply line can be easily disconnected from the mains.
  • Page 34 Electrical connection Proline Promag L 400 HART Capacitance: core/shield ≤420 pF/m (128 pF/ft) Operating temperature –20 to +80 °C (–68 to +176 °F) Coil current cable Standard cable (18 AWG) with common, braided copper shield ( ~ 7 mm (0.28")) 2 ×0.75 mm...

  • Page 35: Terminal Assignment

    Proline Promag L 400 HART Electrical connection 7.1.3 Terminal assignment Transmitter 0-20 mA/4-20 mA HART connection version with additional outputs and inputs + - + - + - + - 23 20 21 26 27 24 25 A0020424 Supply voltage...

  • Page 36: Pin Assignment, Device Plug

    Electrical connection Proline Promag L 400 HART Remote version 6 5 7 8 4 37 36 42 41 n.c. n.c. n.c. 5 7 4 37 42 41 A0020534  8 Remote version terminal assignment Transmitter wall-mount housing Sensor connection housing...

  • Page 37: Preparing The Connecting Cable For The Remote Version

    Proline Promag L 400 HART Electrical connection 7.1.6 Preparing the connecting cable for the remote version When terminating the connecting cable, pay attention to the following points: • In the case of electrode cables, make sure that the ferrules do not touch the core shields on the sensor side.

  • Page 38: Connecting The Measuring Device

    Electrical connection Proline Promag L 400 HART Sensor Electrode cable Coil current cable 20 (0.79)* 160 (6.30)* 20 (0.79)* 170 (6.69)* 70 (2.76) 80 (3.15) 50 (1.97) 50 (1.97) 18.5 (0.73) 10 (0.39) 6 (0.24) 8 (0.31) ³1 (0.04) A0016489...

  • Page 39: Connecting The Remote Version

    Proline Promag L 400 HART Electrical connection Connection via terminals TX 20 + - + - + - + - 23 20 21 26 27 24 25 A0017268  11 Connecting the supply voltage and 0-20 mA/4-20 mA HART with additional outputs and inputs 1.
  • Page 40 Electrical connection Proline Promag L 400 HART TX 20 6 5 7 8 4 37 36 42 41 A0017445  12 Transmitter: main electronics module with terminals 1. Loosen the 4 fixing screws on the housing cover. 2. Open the housing cover.

  • Page 41: Ensuring Potential Equalization

    Proline Promag L 400 HART Electrical connection 6. Firmly tighten the cable glands. 7. WARNING! Housing degree of protection voided due to insufficient sealing of the housing. Screw in the screw without using any lubricant. The threads on the cover are coated with a dry lubricant.
  • Page 42 Electrical connection Proline Promag L 400 HART 1. Connect both sensor flanges to the pipe flange via a ground cable and ground them. 2. If DN ≤ 300 (12"): Mount the ground cable directly on the conductive flange coating of the sensor with the flange screws.If DN ≥ 350 (14"): Mount the ground cable directly on the metal transport bracket.Observe torques (→...

  • Page 43: Special Connection Instructions

    Proline Promag L 400 HART Electrical connection – A0016319  17 Potential equalization and cathodic protection Isolation transformer power supply Electrically isolated from the pipe Capacitor Ground cable Copper wire, at least 6 mm (0.0093 in 1. Connect the measuring device to the power supply such that it is floating in relation to the protective ground.

  • Page 44: Ensuring The Degree Of Protection

    Electrical connection Proline Promag L 400 HART Ensuring the degree of protection 7.4.1 Degree of protection IP66/67, Type 4X enclosure The measuring device fulfills all the requirements for the IP66/67 degree of protection, Type 4X enclosure. To guarantee IP66/67 degree of protection, Type 4X enclosure, carry out the following steps after the electrical connection: 1.

  • Page 45: Operation Options

    Proline Promag L 400 HART Operation options Operation options Overview of operation options A0015607 Local operation via display module Computer with Web browser (e.g. Internet Explorer) or with operating tool (e.g. FieldCare, AMS Device Manager, SIMATIC PDM) Field Xpert SFX100 Field Communicator 475 Control system (e.g.

  • Page 46: Structure And Function Of The Operating Menu

    Operation options Proline Promag L 400 HART Structure and function of the operating menu 8.2.1 Structure of the operating menu For an overview of the operating menu with menus and parameters (→  157) Operating menu for operators and maintenances...

  • Page 47: Operating Philosophy

    Proline Promag L 400 HART Operation options 8.2.2 Operating philosophy The individual parts of the operating menu are assigned to certain user roles. Each user role corresponds to typical tasks within the device lifecycle. Menu User role and tasks Content/meaning...

  • Page 48: Access To The Operating Menu Via The Local Display

    Operation options Proline Promag L 400 HART Access to the operating menu via the local display 8.3.1 Operational display X X X X X X X 1120.50 A0016502 Operational display Device tag (→  71) Status area Display area for measured values (4-line) Operating elements (→...
  • Page 49 Proline Promag L 400 HART Operation options Display area In the display area, each measured value is prefaced by certain symbol types for further description: Measured variable Measurement channel Diagnostic behavior number ↓ ↓ ↓ Example A0013962 A0013945 A0013948 Appears only if a diagnostics event is present for this measured variable.

  • Page 50: Navigation View

    Operation options Proline Promag L 400 HART 8.3.2 Navigation view In the submenu In the wizard /../Operation 0091-1 /../Curr. output 1 Access stat.disp Assign curr. Operator Volume flow Locking status Display A0013993-EN A0016327-EN Navigation view Navigation path to current position...
  • Page 51 Proline Promag L 400 HART Operation options Display area Menus Symbol Meaning Operation Appears: • In the menu next to the "Operation" selection A0013973 • At the left in the navigation path in the "Operation" menu Setup Appears: • In the menu next to the "Setup" selection A0013974 •...

  • Page 52: Editing View

    Operation options Proline Promag L 400 HART 8.3.3 Editing view Numeric editor Text editor A0013941 A0013999 Editing view Display area of the entered values Input mask Operating elements (→  53) Input mask The following input symbols are available in the input mask of the numeric and text editor:...

  • Page 53: Operating Elements

    Proline Promag L 400 HART Operation options Selection of letters from a to z. abc _ … A0019094 Selection of special characters. "'^ _ … ~& A0019095 Confirms selection. A0013985 Switches to the selection of the correction tools. A0013987 Exits the input without applying the changes.

  • Page 54: Opening The Context Menu

    Operation options Proline Promag L 400 HART Meaning Enter key For operational display • Pressing the key briefly opens the operating menu. • Pressing the key for 2 s opens the context menu. In a menu, submenu • Pressing the key briefly: –...
  • Page 55 Proline Promag L 400 HART Operation options  The context menu is closed and the operational display appears. Calling up the menu via the context menu 1. Open the context menu. 2. Press  to navigate to the desired menu.

  • Page 56: Navigating And Selecting From List

    Operation options Proline Promag L 400 HART 8.3.6 Navigating and selecting from list Different operating elements are used to navigate through the operating menu. The navigation path is displayed on the left in the header. Icons are displayed in front of the individual menus.

  • Page 57: Calling Up Help Text

    Proline Promag L 400 HART Operation options Navigation path "Expert" menu → Direct access The direct access code consists of a 4-digit number and the channel number, which identifies the channel of a process variable: e.g. 0914-1. In the navigation view, this appears on the right-hand side in the header of the selected parameter.

  • Page 58: Changing The Parameters

    Operation options Proline Promag L 400 HART 8.3.9 Changing the parameters For a description of the editing display - consisting of text editor and numeric editor - with symbols (→  52), for a description of the operating elements (→  53) Example: Changing the tag name in the "Tag description"...

  • Page 59: User Roles And Related Access Authorization

    Proline Promag L 400 HART Operation options Ent. access code Invalid or out of range input value Min:0 Max:9999 A0014049-EN 8.3.10 User roles and related access authorization The two user roles "Operator" and "Maintenance" have different write access to the parameters if the customer defines a user-specific access code.

  • Page 60: Access To The Operating Menu Via The Web Browser

    Operation options Proline Promag L 400 HART A0016215-EN After disabling the keypad lock: A0016216-EN If the user attempts to access the operating menu while the keylock is enabled, the message Keylock on also appears. Access to the operating menu via the Web browser 8.4.1...

  • Page 61: Establishing A Connection

    Proline Promag L 400 HART Operation options When installing a new firmware version: To enable correct data display, clear the temporary memory (cache) of the Web browser under Internet options. 8.4.3 Establishing a connection Configuring the Internet protocol of the computer IP address 192.168.1.XXX;...

  • Page 62: User Interface

    Operation options Proline Promag L 400 HART If no action is performed for 10 minutes, the Web browser automatically returns to the login page. 8.4.5 User interface A0017757-EN Picture of device Function row with 6 functions Device tag Header Working area...

  • Page 63: Disabling The Web Server

    Proline Promag L 400 HART Operation options Working area Depending on the selected function and the related submenus, various actions can be performed in this area: • Configuring parameters • Reading measured values • Calling up help text • Starting an upload/download 8.4.6...

  • Page 64: Connecting The Operating Tool

    Operation options Proline Promag L 400 HART 8.5.1 Connecting the operating tool Via HART protocol A0017124  21 Options for remote operation via HART protocol Control system (e.g. PLC) Field Communicator 475 Computer with operating tool (e.g. FieldCare, AMS Device Manager, SIMATIC PDM)

  • Page 65: Field Xpert Sfx100

    FieldCare Function scope FDT-based plant asset management tool from Endress+Hauser. It can configure all smart field devices in a system and helps you manage them. By using the status information, it is also a simple but effective way of checking their status and condition.

  • Page 66: Ams Device Manager

    Operation options Proline Promag L 400 HART User interface Xxxxx Xxxxx A0021053-EN Header Picture of device Device tag (→  71) Status area with status signal (→  114) Display area for current measured values (→  102) Event list with additional functions such as save/load, events list and document creation...

  • Page 67: Field Communicator 475

    Proline Promag L 400 HART Operation options 8.5.6 Field Communicator 475 Function scope Industrial handheld terminal from Emerson Process Management for remote configuration and measured value display via HART protocol. Source for device description files See data (→  68)

  • Page 68: System Integration

    System integration Proline Promag L 400 HART System integration Overview of device description files 9.1.1 Current version data for the device Firmware version 01.04.00 • On the title page of the Operating instructions • On transmitter nameplate(→  14) • Parameter firmware version Diagnostics →...

  • Page 69: Other Settings

    Proline Promag L 400 HART System integration The assignment of the measured variables to the dynamic variables can be modified and assigned as desired via local operation and the operating tool using the following parameters: • Expert → Communication → HART output → Output → Assign PV •...

  • Page 70: Commissioning

    Commissioning Proline Promag L 400 HART Commissioning 10.1 Function check Before commissioning the device, make sure that the post-installation and post- connection checks have been performed. • "Post-installation check" checklist (→  32) • "Post-connection check" checklist (→  44) 10.2...

  • Page 71: Defining The Tag Name

    Proline Promag L 400 HART Commissioning X X X X X X X 20.50 0104-1 Main menu Language English Display/operat. Setup Main menu Display/operat. Setup Diagnostic / ../Setup Status input XXXXXXXXX XXXXXXXXX A0017444-EN  23 Illustrated using the example of the local display Overview of the wizards in the "Setup"...

  • Page 72: Configuring The Status Input

    Commissioning Proline Promag L 400 HART Navigation "Setup" menu → Device tag Parameter overview with brief description Parameters Description User entry Factory setting Device tag Enter tag for measuring point. Max. 32 characters, such as Promag letters, numbers or special characters (e.g.

  • Page 73: Configuring The Current Output

    Proline Promag L 400 HART Commissioning 10.4.3 Configuring the current output The "Current output 1 to 2" wizard guides you systematically through all the parameters that have to be set for configuring the particular current output. Navigation "Setup" menu → Current output 1 to 2 Structure of the wizard Assign curr.

  • Page 74: Configuring The Pulse/Frequency

    Commissioning Proline Promag L 400 HART Parameter overview with brief description Parameters Description Selection / User entry Factory setting Assign current output Select process variable for current output. • Off Volume flow • Volume flow • Mass flow • Flow velocity • Conductivity •...
  • Page 75 Proline Promag L 400 HART Commissioning Structure of the wizard for the pulse output Operating mode Pulse Assign pulse Volume flow Mass flow Volume unit Mass unit Density unit Fixed density Value per pulse Pulse width Failure mode Invert outp.sig.
  • Page 76 Commissioning Proline Promag L 400 HART Parameters Description Selection / User entry Factory setting Density unit Select density unit. Unit choose list Country-specific: • kg/l Result • lb/ft³ The selected unit applies for: • Output • Simulation process variable • Density adjustment (in Expert menu) Fixed density Enter fixed value for medium density.
  • Page 77 Proline Promag L 400 HART Commissioning Structure of the wizard for the frequency output Operating mode Frequency Assign freq. Volume flow Conductivity Mass flow Volume unit Conductiv. unit Mass unit Density unit Fixed density Min. freq. value Max. freq. value Val.
  • Page 78 Commissioning Proline Promag L 400 HART Parameters Description Selection / User entry Factory setting Volume flow unit Select volume flow unit. Unit choose list Country-specific: • l/h Result • gal/min (us) The selected unit applies for: • Output • Low flow cut off •...
  • Page 79 Proline Promag L 400 HART Commissioning Structure of the wizard for the switch output Operating mode Switch Switch out funct Diag. behavior Assign diag. beh Alarm or Warning Alarm warning Invert outp.sig. End of wizard A0017439-EN  28 "Pulse/frequency/switch output 1-2" wizard in the "Setup" menu: "Switch" operating mode (Part 1)
  • Page 80 Commissioning Proline Promag L 400 HART Operating mode Switch Switch out funct Fl. direct. Limit Status check Assign Assign Assign limit dir.check status Conduc- Empty Volume Mass Totalizer Volume Mass Low flow tivity pipe det. flow flow 1/2/3 flow flow...

  • Page 81: Configuring The Local Display

    Proline Promag L 400 HART Commissioning Parameters Description Selection / User entry Factory setting Assign limit Select process variable for limit function. • Off Volume flow • Volume flow • Mass flow • Flow velocity • Conductivity • Totalizer 1 • Totalizer 2 •...
  • Page 82 Commissioning Proline Promag L 400 HART Structure of the wizard Format display Value 1 display 0% bargraph value 1 100% bargraph value 1 Value 2 display Value 3 display 0% bargraph value 3 100% bargraph value 3 Value 4 display...

  • Page 83: Configuring The Hart Input

    Proline Promag L 400 HART Commissioning Parameters Description Selection / User entry Factory setting Value 3 display Select the measured value that is shown on Picklist (see 1st display value) None the local display. 0% bargraph value 3 Enter 0% value for bar graph display.

  • Page 84: Configuring The Output

    Commissioning Proline Promag L 400 HART Parameter overview with brief description Parameters Description Selection / User entry Factory setting Capture mode Select capture mode via burst or master • Off communication. • Burst network • Master network Manufacturer ID Enter manufacture ID of external device.
  • Page 85 Proline Promag L 400 HART Commissioning Structure of the wizard Display damping Damping out. 1 Damping out. 2 Damping out. 3 Assign curr. Volume flow Conductivity Mass flow Assign pulse Volume flow Mass flow Assign freq. Volume flow Conductivity Mass flow...

  • Page 86: Configuring The Low Flow Cut Off

    Commissioning Proline Promag L 400 HART Parameters Description User entry / Selection Factory setting Assign current output Select process variable for current output. • Off Volume flow • Volume flow • Mass flow • Flow velocity • Conductivity • Electronic temperature Assign pulse output Select process variable for pulse output.
  • Page 87 Proline Promag L 400 HART Commissioning Parameter overview with brief description Parameters Description Selection / User entry Factory setting Assign process variable Select process variable for low flow cut off. • Off Volume flow • Volume flow • Mass flow On value low flow cutoff Enter on value for low flow cut off.

  • Page 88: Configuring Empty Pipe Detection

    Commissioning Proline Promag L 400 HART 10.4.9 Configuring empty pipe detection The Empty pipe detection wizard guides you systematically through all the parameters that have to be set for configuring the low flow cut off. Navigation "Setup" menu → Empty pipe detection Structure of the wizard Empty pipe det.
  • Page 89 Proline Promag L 400 HART Commissioning Structure of the wizard Empty pipe det. New adjustment Cancel Empty pipe adj. Full pipe adjust. Progress Busy Not ok Switch point EPD Response time End of wizard A0017210-EN  35 "Empty pipe detection" wizard in the "Setup" menu...

  • Page 90: Advanced Settings

    Commissioning Proline Promag L 400 HART 10.5 Advanced settings The Advanced setup submenu with its submenus contains parameters for specific settings. "Setup" menu → Advanced setup Navigation to the "Advanced setup" submenu X X X X X X X 20.50...

  • Page 91: Setting The System Units

    Proline Promag L 400 HART Commissioning 10.5.1 Setting the system units In the System units submenu the units of all the measured values can be set. Navigation "Setup" menu → System units System units → Volume flow unit Volume unit...

  • Page 92: Carrying Out A Sensor Adjustment

    Commissioning Proline Promag L 400 HART Parameters Description Selection Factory setting Density unit Select density unit. Unit choose list Country-specific: • kg/l Result • lb/ft³ The selected unit applies for: • Output • Simulation process variable • Density adjustment (in Expert menu) Corrected volume flow unit Select corrected volume flow unit.
  • Page 93 Proline Promag L 400 HART Commissioning Parameter overview with brief description Parameters Description Selection Factory setting Assign process variable Select process variable for totalizer. • Off Volume flow • Volume flow • Mass flow Unit totalizer Select process variable totalizer unit.

  • Page 94: Carrying Out Additional Display Configurations

    Commissioning Proline Promag L 400 HART 10.5.4 Carrying out additional display configurations In the "Display" submenu you can set all the parameters involved in the configuration of the local display. Navigation "Setup" menu → Advanced setup → Display Structure of the submenu Display →...
  • Page 95 Proline Promag L 400 HART Commissioning Parameter overview with brief description Parameters Description Selection / User entry Factory setting Format display Select how measured values are shown on • 1 value, max. size 1 value, max. size the display. • 1 bargraph + 1 value •...

  • Page 96: Performing Electrode Cleaning

    Commissioning Proline Promag L 400 HART Parameters Description Selection / User entry Factory setting Display language Set display language. • English English • Deutsch • Français • Español • Italiano • Nederlands • Portuguesa • Polski • русский язык (Russian) • Svenska •...

  • Page 97: Simulation

    Proline Promag L 400 HART Commissioning Parameter overview with brief description Parameters Description Selection / User entry / User Factory setting interface Electrode cleaning circuit Enable the cyclic electrode cleaning circuit. • Off • On ECC duration Enter the duration of electrode cleaning in 0.01 to 30 s...

  • Page 98: Protecting Settings From Unauthorized

    Commissioning Proline Promag L 400 HART Parameter overview with brief description Parameters Prerequsite Description Selection / User Factory setting entry Assign simulation process variable – Select a process variable for • Off the simulation process that is • Volume flow activated. • Mass flow •...

  • Page 99: Write Protection Via Access Code

    Proline Promag L 400 HART Commissioning 10.7.1 Write protection via access code The effects of the customer-specific access code are as follows: • Via local operation, the parameters for the measuring device configuration are write- protected and their values can no longer be changed.

  • Page 100: Write Protection Via Write Protection

    Commissioning Proline Promag L 400 HART If no action is performed for 10 minutes, the Web browser automatically returns to the login page. The user role with which the user is currently logged on via the Web browser is indicated by the Access status tooling parameter. Navigation path: Operation →...
  • Page 101 Proline Promag L 400 HART Commissioning 3. WARNING! Excessive tightening torque applied to the fixing screws! Risk of damaging the plastic transmitter. Tighten the fixing screws as per the tightening torque (→  30). Reverse the removal procedure to reassemble the transmitter.

  • Page 102: Operation

    Operation Proline Promag L 400 HART Operation 11.1 Reading device locking status The write protection types that are currently active can be determined using the "Locking status" parameter. "Operation" menu → Locking status Function scope of "Locking status" parameter Options...

  • Page 103: Totalizer

    Proline Promag L 400 HART Operation Structure of the submenu Parameter overview with brief description Parameters Description User interface Volume flow Displays the volume flow currently measured. Signed floating-point number Mass flow Displays the mass flow currently calculated. Signed floating-point number Conductivity Displays the corrected volume flow currently calculated.

  • Page 104: Output Values

    Operation Proline Promag L 400 HART Structure of the submenu Input values → Value status input Parameter overview with brief description Parameters Description User interface Factory setting Value status input Displays the current input signal level. • High • Low 11.4.4...

  • Page 105: Adapting The Measuring Device To The Process

    Proline Promag L 400 HART Operation 11.5 Adapting the measuring device to the process conditions The following are available for this purpose: • Basic settings using the Setup menu(→  70) • Advanced settings using the Advanced setup submenu(→  90) 11.6...

  • Page 106: Function Scope Of "Reset All Totalizers" Parameter

    Operation Proline Promag L 400 HART 11.6.2 Function scope of "Reset all totalizers" parameter Options Description Reset + totalize Resets all totalizers to 0 and restarts the totaling process. This deletes all the flow values previously totalized. 11.7 Showing data logging In the device, the extended function of the HistoROM must be enabled (order option) so that the "Data logging"...
  • Page 107 Proline Promag L 400 HART Operation Parameter overview with brief description Parameters Description Selection / User entry Factory setting Assign channel 1 Assign process variable to logging channel. • Off • Volume flow • Mass flow • Conductivity • Electronic temperature • Current output 1 Assign channel 2 Assign process variable to logging channel.

  • Page 108: Diagnostics And Troubleshooting

    Diagnostics and troubleshooting Proline Promag L 400 HART Diagnostics and troubleshooting 12.1 General troubleshooting For local display Problem Possible causes Remedy Local display dark and no output Supply voltage does not match that Apply the correct supply voltage signals specified on the nameplate.

  • Page 109: Diagnostic Information Via Light Emitting

    Proline Promag L 400 HART Diagnostics and troubleshooting For access Problem Possible causes Remedy No write access to parameters Hardware write protection enabled Set the write protection switch on the main electronics module to the OFF position (→  100).
  • Page 110 Diagnostics and troubleshooting Proline Promag L 400 HART Color Meaning Flashing orange Activity present Communication Flashing white HART communication is active. Alarm Green Measuring device is ok Flashing green Measuring device not configured Firmware error Main error Flashing red Error...

  • Page 111: Diagnostic Information On Local Display

    Proline Promag L 400 HART Diagnostics and troubleshooting 12.3 Diagnostic information on local display 12.3.1 Diagnostic message Faults detected by the self-monitoring system of the measuring device are displayed as a diagnostic message in alternation with the operational display. Operational display in alarm condition...
  • Page 112 Diagnostics and troubleshooting Proline Promag L 400 HART Diagnostic behavior Symbol Meaning Alarm • Measurement is interrupted. • Signal outputs and totalizers assume the defined alarm condition. • A diagnostic message is generated. A0013961 • The background lighting changes to red.

  • Page 113: Calling Up Remedial Measures

    Proline Promag L 400 HART Diagnostics and troubleshooting 12.3.2 Calling up remedial measures X X X X X X X X X X X X X X 20.50 S801 Supply voltage Menu Diagnostic list Diagnostics 1 S801 Supply voltage Diagnostics 2...

  • Page 114: Diagnostic Information In The Web Browser

    Diagnostics and troubleshooting Proline Promag L 400 HART 12.4 Diagnostic information in the Web browser 12.4.1 Diagnostic options Any faults detected by the measuring device are displayed in the Web browser on the home page once the user has logged on.

  • Page 115: Diagnostic Information In Fieldcare

    Proline Promag L 400 HART Diagnostics and troubleshooting 12.5 Diagnostic information in FieldCare 12.5.1 Diagnostic options Any faults detected by the measuring device are displayed on the home page of the operating tool once the connection has been established. XXXXXXXX...

  • Page 116: Calling Up Remedy Information

    Diagnostics and troubleshooting Proline Promag L 400 HART 12.5.2 Calling up remedy information Remedy information is provided for every diagnostic event to ensure that problems can be rectified quickly: • On the home page Remedy information is displayed in a separate field below the diagnostics information.

  • Page 117: Adapting The Diagnostic Information

    Proline Promag L 400 HART Diagnostics and troubleshooting Diagnostic information The fault can be identified using the diagnostic information. The short text helps you by providing information about the fault. In addition, the corresponding symbol for the diagnostic behavior is displayed in front of the diagnostic information on the local display.
  • Page 118 Diagnostics and troubleshooting Proline Promag L 400 HART You can assign the following options to the diagnostic number as the diagnostic behavior: Options Description Alarm Measurement is interrupted. Signal outputs and totalizers assume the defined alarm condition. A diagnostic message is generated.

  • Page 119: Overview Of Diagnostic Information

    Proline Promag L 400 HART Diagnostics and troubleshooting 12.8 Overview of diagnostic information The amount of diagnostic information and the number of measured variables affected increase if the measuring device has one or more application packages. Status Diagnostic Diagnostic signal...
  • Page 120 Diagnostics and troubleshooting Proline Promag L 400 HART Status Diagnostic Diagnostic signal behaviour Short text Repairing action number from the from the factory factory Data storage 1. Restart device Alarm 2. Contact service Memory content 1. Transfer data or reset device Alarm 2.
  • Page 121 Proline Promag L 400 HART Diagnostics and troubleshooting Status Diagnostic Diagnostic signal behaviour Short text Repairing action number from the from the factory factory Simulation pulse output Deactivate simulation pulse output Warning Switch output Deactivate simulation switch output Warning simulation...

  • Page 122: Pending Diagnostic Events

    Diagnostics and troubleshooting Proline Promag L 400 HART Status Diagnostic Diagnostic signal behaviour Short text Repairing action number from the from the factory factory Wet steam detection 1. Check pressure, temperature Warning uncertain 2. Check flow velocity 3. Check for flow fluctuation Input signal 1.

  • Page 123: 12.10 Diagnostic List

    Proline Promag L 400 HART Diagnostics and troubleshooting 12.10 Diagnostic list In the Diagnostic list submenu, up to 5 currently pending diagnostic events can be displayed along with the related diagnostic information. If more than 5 diagnostic events are pending, the events with the highest priority are shown on the display.

  • Page 124: 12.11.2 Filtering The Event Logbook

    Diagnostics and troubleshooting Proline Promag L 400 HART To call up the measures to rectify a diagnostic event: • Via local display (→  113) • Via Web browser (→  114) • Via "FieldCare" operating tool (→  116) For filtering the displayed event messages (→...

  • Page 125: 12.12 Resetting The Measuring Device

    Proline Promag L 400 HART Diagnostics and troubleshooting Info number Info name I1398 CDI: access status changed I1444 Device verification passed I1445 Device verification failed I1446 Device verification active I1447 Record application reference data I1448 Application reference data recorded I1449 Recording application ref.
  • Page 126 Diagnostics and troubleshooting Proline Promag L 400 HART Order code Extended order code 1 Extended order code 2 Extended order code 3 ENP version Device revision Device ID Device type Manufacturer ID IP address Subnet mask Default gateway Parameter overview with brief description...

  • Page 127: 12.14 Firmware History

    "Manufacturer' s information" document. The manufacturer' s information is available: • In the Download Area of the Endress+Hauser Internet site: www.endress.com → Download • Specify the following details: –...

  • Page 128: Maintenance

    Replacement seals (accessory) (→  156) 13.2 Measuring and test equipment Endress+Hauser offers a wide variety of measuring and test equipment, such as W@M or device tests. Your Endress+Hauser Sales Center can provide detailed information on the services. For a list of some of the measuring and test equipment, refer to the "Accessories"...

  • Page 129: Repair

    • Spare parts are grouped into logical kits with the associated Installation Instructions. • Repairs are carried out by Endress+Hauser Service or by correspondingly trained customers. • Certified devices can be converted into other certified devices by Endress+Hauser Service or at the factory only. Notes for repair and conversion For repair and modification of a measuring device, observe the following notes: •...

  • Page 130: Disposing Of The Measuring Device

    Repair Proline Promag L 400 HART 2. WARNING! Danger to persons from process conditions. Beware of hazardous process conditions such as pressure in the measuring device, high temperatures or aggressive fluids. Carry out the mounting and connection steps from the chapters "Mounting the measuring device"...

  • Page 131: Accessories

    Various accessories, which can be ordered with the device or subsequently from Endress +Hauser, are available for the device. Detailed information on the order code in question is available from your local Endress+Hauser sales center or on the product page of the Endress+Hauser website: www.endress.com.

  • Page 132: Service-Specific Accessories

    The application already contains the data of your Endress+Hauser device. Endress +Hauser also takes care of maintaining and updating the data records.

  • Page 133: Technical Data

    Proline Promag L 400 HART Technical data Technical data 16.1 Application The measuring device described in these Instructions is intended only for flow measurement of liquids with a minimum conductivity of 5 μS/cm. Depending on the version ordered, the measuring device can also measure potentially explosive, flammable, poisonous and oxidizing media.
  • Page 134 Technical data Proline Promag L 400 HART Nominal Recommended Factory settings diameter flow Full scale value current min./max. full scale value Pulse value Low flow cut off output (v ~ 0.3/10 m/s) (~ 2 pulse/s) (v ~ 0.04 m/s) (v ~ 2.5 m/s)
  • Page 135 Proline Promag L 400 HART Technical data Nominal Recommended Factory settings diameter flow Full scale value current min./max. full scale value Pulse value Low flow cut off output (v ~ 0.3/10 m/s) (~ 2 pulse/s) (v ~ 0.04 m/s) (v ~ 2.5 m/s)

  • Page 136: Output

    Technical data Proline Promag L 400 HART Input signal Status input Maximum input values • DC 30 V • 6 mA Response time Adjustable: 5 to 200 ms Input signal level • Low signal: DC –3 to +5 V • High signal: DC 12 to 30 V Assignable functions •...
  • Page 137 Proline Promag L 400 HART Technical data Pulse/pause ratio Assignable measured • Volume flow variables • Mass flow • Flow velocity • Conductivity • Electronics temperature Switch output Switching behavior Binary, conductive or non-conductive Switching delay Adjustable: 0 to 100 s...

  • Page 138: Power Supply

    Technical data Proline Promag L 400 HART Failure mode Choose from: • Actual value • Defined value: 0 to 12 500 Hz • 0 Hz Switch output Failure mode Choose from: • Current status • Open • Closed Local display...
  • Page 139 Proline Promag L 400 HART Technical data Supply voltage Transmitter Order code for "Power supply" Terminal voltage Frequency range AC100 to 240 V 50/ 60 Hz, ±4 Hz Option L AC/DC24 V 50/ 60 Hz, ±4 Hz Power consumption Order code for Maximum "Output"...

  • Page 140: Performance Characteristics

    Technical data Proline Promag L 400 HART 16.6 Performance characteristics Reference operating In accordance with DIN EN 29104 conditions • Fluid temperature: +28±2 °C (+82±4 °F) • Ambient temperature range: +22±2 °C (+72±4 °F) • Warm-up period:30 min Installation • Inlet run > 10 × DN •...

  • Page 141: Installation

    Proline Promag L 400 HART Technical data Repeatability o.r. = of reading Volume flow Max. ±0.1 % o.r. ± 0.5 mm/s (0.02 in/s) Electrical conductivity Max. ±5 % o.r. Influence of ambient o.r. = of reading; o.f.s. = of full scale value...

  • Page 142: Process

    Technical data Proline Promag L 400 HART Mechanical load • Protect the transmitter housing against mechanical effects, such as shock or impact; the use of the remote version is sometimes preferable. • Never use the transmitter housing as a ladder or climbing aid.

  • Page 143: 16.10 Mechanical Construction

    Proline Promag L 400 HART Technical data Flow limit The diameter of the pipe and the flow rate determine the nominal diameter of the sensor. The optimum flow velocity is between 2 to 3 m/s (6.56 to 9.84 ft/s). Also match the velocity of flow (v) to the physical properties of the fluid: •...
  • Page 144 Technical data Proline Promag L 400 HART Nominal EN (DIN) ASME, AWWA diameter [mm] [in] Pressure [kg] Pressure [kg] Pressure [kg] Pressure [kg] Pressure [kg] Pressure [kg] rating rating rating rating rating rating PN 6 PN 10 PN 16 Class 150...
  • Page 145 Proline Promag L 400 HART Technical data Weight in US units Lap joint flange; fixed flange DN ≥ 350 (14") Nominal diameter ASME, AWWA [mm] [in] Pressure rating [lbs] Class 150 2 ½ Class 150 – Class 150 Class 150 Class 150 –...
  • Page 146 Technical data Proline Promag L 400 HART Sensor remote version Weight data: • Including sensor connection housing • Excluding the connecting cable • Excluding packaging material Weight in SI units Lap joint flange; fixed flange DN ≥ 350 (14") Nominal...
  • Page 147 Proline Promag L 400 HART Technical data Lap joint flange, stamped plate Nominal diameter EN (DIN) [mm] [in] Pressure rating [kg] PN 10 2 ½ PN 10 PN 10 PN 10 PN 10 PN 10 PN 10 PN 10 PN 10 Weight in US units Lap joint flange;...
  • Page 148 Technical data Proline Promag L 400 HART Nominal diameter ASME, AWWA [mm] [in] Pressure rating [lbs] 2 000 Class D 6858 – Class D 8273 – Class D 10571 Measuring tube Nominal diameter Pressure rating Measuring tube internal diameter specification...
  • Page 149 Proline Promag L 400 HART Technical data Nominal diameter Pressure rating Measuring tube internal diameter EN (DIN) ASME AS 2129 Hard rubber Polyurethane PTFE AWWA AS 4087 [mm] [in] [mm] [in] [mm] [in] [mm] [in] PN 10 – – 27.3 27.4...
  • Page 150 Technical data Proline Promag L 400 HART Nominal diameter Pressure rating Measuring tube internal diameter EN (DIN) ASME AS 2129 Hard rubber Polyurethane PTFE AWWA AS 4087 [mm] [in] [mm] [in] [mm] [in] [mm] [in] – – Class D –...
  • Page 151 Proline Promag L 400 HART Technical data Compact and remote versions and sensor connection housing Cable entry/cable gland Material Cable gland M20 × 1.5 Plastic Remote version: cable gland M20 × 1.5 • Sensor connection housing: Nickel-plated brass • Option CK "IP68, Type 6P, waterproof"...
  • Page 152 Technical data Proline Promag L 400 HART Electrodes 1.4435 (304L), Alloy C22 Process connections EN 1092-1 (DIN 2501) • DN ≤ 300 (12"): 1.0038 (S235JRG2), 1.4301 (304), 1.4306 (304L), 1.4307 (304L) • DN ≥ 350 (14"): 1.0038 (S235JRG2), A105 ASME B16.5 •...

  • Page 153: 16.11 Operability

    Proline Promag L 400 HART Technical data Process connections Flange connections: • EN 1092-1 (DIN 2501) – DN ≤ 300 (12"): lap joint flange (PN 10/16), lap joint flange, stamped plate (PN 10) = form A – DN ≥ 350 (14"): fixed flange (PN 6/10) = flat face •...

  • Page 154: 16.12 Certificates And Approvals

    EC Directives. These are listed in the corresponding EC Declaration of Conformity along with the standards applied. Endress+Hauser confirms successful testing of the device by affixing to it the CE mark. C-Tick symbol The measuring system meets the EMC requirements of the "Australian Communications and Media Authority (ACMA)".

  • Page 155: 16.13 Application Packages

    The application packages can be ordered from Endress+Hauser either directly with the device or subsequently. Detailed information on the order code in question is available from your local Endress+Hauser sales center or on the product page of the Endress+Hauser website: www.endress.com.

  • Page 156: 16.14 Accessories

    Overview of accessories available for order (→  131) 16.15 Documentation The following document types are available: • On the CD-ROM supplied with the device • In the Download Area of the Endress+Hauser Internet site: www.endress.com → Download Standard documentation Communication...

  • Page 157: Appendix

    Proline Promag L 400 HART Appendix Appendix 17.1 Overview of the operating menu The following table provides an overview of the entire operating menu structure with menus and parameters. The direct access code to the parameter is given in brackets. The page reference indicates where a description of the parameter can be found in the manual.
  • Page 158 Appendix Proline Promag L 400 HART Mass flow unit Volume flow unit Density unit Conductivity unit Current span 0/4 mA value 20 mA value Failure mode Failure current PFS output1 to 2 → (→  74) Pulse output → (→  74)
  • Page 159 Proline Promag L 400 HART Appendix Volume unit Density unit Unit totalizer 1 to 3 Minimum frequency value Maximum frequency value Measuring value at minimum frequency Measuring value at maximum frequency Failure mode Failure frequency Invert output signal Switch output →...
  • Page 160 Appendix Proline Promag L 400 HART Invert output signal Display → (→  81) Format display Value 1 display 0% bargraph value 1 100% bargraph value 1 Value 2 display Value 3 display 0% bargraph value 3 100% bargraph value 3 Value 4 display Output cond.
  • Page 161 Proline Promag L 400 HART Appendix Device ID Device type Manufacturer ID Burst command Slot number Timeout Failure mode Failure value Advanced setup → (→  90) Enter access code (→  59) System units → (→  91) Volume flow unit...
  • Page 162 Appendix Proline Promag L 400 HART Value 2 display Decimal places 2 Value 3 display 0% bargraph value 3 100% bargraph value 3 Decimal places 3 Value 4 display Decimal places 4 Display language Display interval Display damping Header Header text...
  • Page 163 Proline Promag L 400 HART Appendix Diagnostic list → (→  123) Diagnostics 1 to 5 → (→  123) Event logbook Filter options (→  124) Device information → (→  125) Device tag Serial number Firmware version Device name...
  • Page 164 Appendix Proline Promag L 400 HART Measured current 1 Pulse output1 to 2 Output frequency1 to 2 Switch status1 to 2 Data logging → (→  106) Assign channel 1-4 Logging interval Clear logging data Simulation → (→  97)
  • Page 165 Proline Promag L 400 HART Appendix Verification mode Information external device External reference voltage 1 to 2 Start verification Progress Measured values Output values Status Overall result Verification result → Date/time Verification ID Operating time Overall result Sensor Sensor electronic module...
  • Page 166 Appendix Proline Promag L 400 HART Display language (0104) (→  70) Format display (0098) Value 1 display (0107) 0% bargraph value 1 (0123) 100% bargraph value 1 (0125) Decimal places 1 (0095) Value 2 display (0108) Decimal places 2 (0117)
  • Page 167 Proline Promag L 400 HART Appendix (→  119) Assign behavior of diagnostic no. 443 (0659) Assign behavior of (→  119) diagnostic no. 531 (0741) (→  119) Assign behavior of diagnostic no. 832 (0681) Assign behavior of (→  119) diagnostic no.
  • Page 168 Appendix Proline Promag L 400 HART Totalizer value 1 to 3 (0911) Totalizer overflow 1 to 3 (0910) Input values → (→  103) Value status input (1353) Output values → (→  104) Output current 1 (0361) Measured current output...
  • Page 169 Proline Promag L 400 HART Appendix Flow damping (6661) Flow override (1839) Conductivity damping (1803) Conductivity measurement (6514) → (→  86) Low flow cut off Assign process variable (1837) On value low flow cutoff (1805) Off value low flow cutoff...
  • Page 170 Appendix Proline Promag L 400 HART External value (6504) External density (6630) Fixed density (6623) Sensor adjustment → (→  92) Installation direction (1809) Integration time (6533) Measuring period (6536) Variable adjust → (→  92) Volume flow offset (1831)
  • Page 171 Proline Promag L 400 HART Appendix Output → Current output 1 → (→  73) Assign current output (0359) Current span (0353) Fixed current (0365) 0/4 mA value (0367) 20 mA value (0372) Measuring mode (0351) Damping (0363) Response time (0378)
  • Page 172 Appendix Proline Promag L 400 HART Maximum frequency value (0454) Measuring value at minimum frequency (0476) Measuring value at maximum frequency (0475) Measuring mode (0479) Damping output (0477) Response time (0491) Failure mode (0451) Failure frequency (0474) Output frequency 1 to 2...
  • Page 173 Proline Promag L 400 HART Appendix Configuration → (→  83) Capture mode (7001) Assign external process variable (7002) Device ID (7007) Device type (7008) Manufacturer ID (7009) Burst command (7006) Slot number (7010) Timeout (7005) Failure mode (7011) Failsafe value (7012) →...
  • Page 174 Appendix Proline Promag L 400 HART Hardware revision (0206) Software revision (0224) Output → (→  68) Assign PV (0234) Primary variable (PV) (0201) Assign SV (0235) Secondary variable (SV) (0226) Assign TV (0236) Tertiary variable (TV) (0228) Assign QV (0237)
  • Page 175 Proline Promag L 400 HART Appendix → (→  108) Diagnostics Actual diagnostics (→  123) (0691) Previous diagnostics (0690) Operating time from restart (0653) Operating time (0652) Diagnostic list → Diagnostics 1 to 5 (692 to 696) Event logbook →...
  • Page 176 Appendix Proline Promag L 400 HART Main electronic → temperature Minimum value (6547) Maximum value (6545) Heartbeat* → (→ SD01183D) → Base settings Customer (2754) Location (2755) Performing verification → Year (2846) Month (2845) Day (2842) Hour (2843) AM/PM (2813)
  • Page 177 Proline Promag L 400 HART Appendix Sensor (12152) Sensor electronics module (12151) I/O module (12145) Monitoring result → Noise (12158) Coil current shot time (12150) Reference electrode potential against PE (12155) Simulation → (→  97) Assign simulation process variable (1810)

  • Page 178: Index

    Index Proline Promag L 400 HART Index Design Measuring device ......12 Access authorization to parameters Designated use .
  • Page 179 Proline Promag L 400 HART Index Degree of protection ..... . . 44 Field Communicator ..... . 64 Galvanic isolation .
  • Page 180 Index Proline Promag L 400 HART Main electronics module ..... . 12 Operable flow range ......135 Maintenance tasks .
  • Page 181 Proline Promag L 400 HART Index Post-installation check (checklist) ....32 Operating language ..... . . 70 Potential equalization .
  • Page 182 Index Proline Promag L 400 HART For menus ......51 Define access code ......99 For parameters .
  • Page 184 www.addresses.endress.com...

Table of Contents