IDTECH OMNI Quick Start Manual
  1. Manuals
  2. Brands
  3. IDTECH Manuals
  4. Card Reader
  5. OMNI
  6. Quick start manual

IDTECH OMNI Quick Start Manual

Combined bar code and magnetic stripe reader, rs-232 serial interface
Hide thumbs Also See for OMNI:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
ID TECH
10721 Walker Street
Cypress, California 90630
(714) 761-6368
www.idtechproducts.com
80028507-002
ID TECH
10721 Walker Street
Cypress, California 90630
(714) 761-6368
www.idtechproducts.com
80028507-002
R09/06
R09/06
OMNI
Combined Bar Code
and
Magnetic Stripe Reader
RS-232 Serial Interface
Quickstart Manual
OMNI
Combined Bar Code
and
Magnetic Stripe Reader
RS-232 Serial Interface
Quickstart Manual
TM
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OMNI and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for IDTECH OMNI

Summary of Contents for IDTECH OMNI

  • Page 1 OMNI Combined Bar Code Magnetic Stripe Reader RS-232 Serial Interface Quickstart Manual ID TECH 10721 Walker Street Cypress, California 90630 (714) 761-6368 www.idtechproducts.com 80028507-002 R09/06 OMNI Combined Bar Code Magnetic Stripe Reader RS-232 Serial Interface Quickstart Manual ID TECH 10721 Walker Street...

  • Page 2: Data Editing

    DATA EDITING The Omni has a data editing feature incorporated into its firmware. This feature allows the data read from the magnetic stripe or the bar code to be sent to the host in the exact format expected by the host software, eliminating the need for modifications to the application software.

  • Page 3: Agency Approved

    ID TECH is a registered trademark of International Technologies & Systems LRC: Check character, following end sentinel. Corporation. Omni and Value through Innovation are trademarks of International Technologies & Systems Corporation. CDL: Old California Drivers License format.
  • Page 4 UPC-A, -E Enabled, Enabled SPECIFICATIONS Send Number System Digit Send Check Digit Expand UPC-E Power Requirements, Read 2, 5 Digit Addendum No, No Bar Code: Power +5 VDC +/-10% (35mA maximum). Ground 0 VDC (GND). Addendum required Power Requirements, Add Addendum Separator Magnetic: Power +5 VDC +/-10% (50mV ripple maximum).
  • Page 5 Interleaved 2 of 5 Enabled Bar Code Resolution: .006 (6 mil) minimum. Fixed Length Check Digit None Magnetic Stripe Minimum Length Formats: ISO 7811, AAMVA, and CA DMV. Maximum Length Swipe Speed: Bar Code: 5 to 65 inches per second, bi-directional. Industrial 2 of 5 Enabled Magnetic Stripe: 3 to 60 inches per second, bi-...
  • Page 6 Terminal Selection Type RS-232 (serial) DESCRIPTION General Selection Beep Volume High This slot reader can scan and decode most popular bar codes, as well as read Intercharacter Delay 5 milliseconds 1, 2, or 3 tracks of magnetic stripe information. It also has full data editing Interblock Delay 0 milliseconds capabilities.

  • Page 7: Troubleshooting

    DB-9 connector. Care must be taken to ensure the power module operates within +5 VDC 10%. DEFAULT SETTINGS TABLE The Omni reader is shipped from the factory with the following bar code default settings already programmed: TROUBLESHOOTING HOST CONNECTIONS The Omni reader is easy to install and use.

  • Page 8: Operation

    CONFIGURATION OPERATION The reader may be configured to your specific application. Configuration The reader is easy to operate. Just follow these simple steps: settings enable the reader to work with the host system. These settings are programmed into the reader by sending Setup Commands from the host 1.

Table of Contents