Keithley PDISO-8 User Manual page 10

List of Figures
Figure 2-1 Block Diagram of the PDISO-8 . . . . . . . . . . . . . 2-1
Figure 3-1 Switch Locations . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Figure 3-2 8-Position Response Switch . . . . . . . . . . . . . . . 3-10
Figure 3-3 An AIO Panel example . . . . . . . . . . . . . . . . . . . 3-12
Figure 3-4 DIO channel tab example . . . . . . . . . . . . . . . . . 3-13
Figure 3-5 Configuring the digital I/O channels as inputs
and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Figure 3-6 Configuring channel 0 for output bit
pattern A . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Figure 3-7 An AIO Panel example . . . . . . . . . . . . . . . . . . . 3-17
Figure 3-8 Configuring the digital I/O channels as inputs
and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Figure 3-9 Configuring channel 0 for output bit
pattern A . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Figure 3-10 Configuring channel 0 for output bit
pattern B . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Figure 4-1 Pin Assignments for the Main I/O Connector . . 4-1
Figure 4-2 Attaching an STA-U or STP-37/FC to a
PDISO-8 Board . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Figure 4-3 Layout of STC-37 Screw Terminal
Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Figure 4-4 Attaching an STC-37 Accessory . . . . . . . . . . . . 4-4
Figure 4-5 Adding a Snubber Network Across Relay
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-6 Equivalent Circuit of an Isolated
Control Input . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-7 Unfiltered Opto-Isolator Output with
AC Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Figure 6-1 An AIO Panel example . . . . . . . . . . . . . . . . . . . . 6-2
Figure 6-2 DIO channel tab example . . . . . . . . . . . . . . . . . . 6-3
Figure 6-3 Configuring the digital I/O channels as inputs
and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Figure 6-4 Configuring channel 0 for output bit pattern A . 6-5
Figure 6-5 An AIO Panel example . . . . . . . . . . . . . . . . . . . . 6-7
Figure 6-6 Configuring the digital I/O channels as inputs
and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Figure 6-7 Configuring channel 0 for output bit pattern A . 6-8
Figure 6-8 Configuring channel 0 for output bit pattern B . 6-9
Figure B-1 Main I/O Connector Pin Assignments . . . . . . . . B-1
iii